Snapper ESZT18336BVE Problem Probable Cause, Corrective Action, Trouble Shooting on Next

Page 27

TROUBLESHOOTING

PROBLEM

 

PROBABLE CAUSE

Starter Will Not Crank

1. Battery dead.

Engine

2. Blown fuse.

 

3.

Electrical connections loose or corroded.

 

4.

Defective ignition switch.

 

5.

Blade engagement switch in the “ON” position.

 

6.

Motion Control Levers not in neutral lock position.

 

7.

Park brake not engaged.

 

8.

Faulty parking brake, blade or ignition switch.

 

9.

Faulty engine starter.

 

10. Faulty starter solenoid.

Engine Will Crank But

1. Fuel tank empty or fuel shut-off valve closed.

Not Start

2. Engine needs choking.

3.Spark plug wire disconnected.

4.Battery weak or dead.

5.Faulty parking brake, blade or ignition switch.

Engine Will Not Start 1. Blade engagement switch in the “ON” position. Using Recoil Starter 2. Park brake not engaged.

(Applicable models) 3. Motion Control Levers not in neutral lock position.

 

4.

Fuel tank empty or fuel shut-off valve closed.

 

5.

Engine needs choking.

 

6.

Blown Fuse.

 

7.

Faulty relay switch.

 

8.

Faulty parking brake or blade switch.

Engine Stalls After

1. Operator not in seat.

Running

2. Engine speed control in the “CHOKE” position.

3.Fuel tank empty.

4.Engine air pre-cleaner and or air cleaner dirty.

5.Spark plug defective or gap set improperly.

6.Fuel filter stopped up.

7.Water, debris or stale fuel in fuel system.

Engine Loses Power 1. Excessive load on engine.

2.Engine air pre-cleaner or air cleaner dirty

3.Spark plug faulty.

4.Water, debris or stale fuel in fuel system.

5.Debris build up on engine cooling screen.

Engine Backfires When 1. Throttle control set too “FAST”.

Turned To “STOP”

CORRECTIVE ACTION

1.Service battery.

2.Replace fuse.

3.Clean and check connections for good contact.

4.Contact authorized SNAPPER dealer.

5.Push blade engagement switch in to “OFF”.

6.Lift levers into neutral lock position.

7.Engage park brake.

8.Contact authorized SNAPPER dealer.

9.Replace engine starter.

10.Replace starter solenoid.

1.Fill fuel tank with fresh fuel & open fuel valve.

2.Move choke control to “CHOKE” position.

3.Place spark plug wire onto spark plug.

4.Service battery.

5.Contact authorized SNAPPER dealer.

1.Push blade engagement switch in to “OFF”.

2.Engage park brake.

3.Lift levers into neutral lock position.

4.Fill fuel tank with fresh fuel & open fuel valve.

5.Move choke control to “CHOKE” position.

6.Replace with new 20 AMP fuse.

7.Contact authorized SNAPPER dealer.

8.Contact authorized SNAPPER dealer.

1.Sit in operator’s seat.

2.Move speed control back past “Fast” detent.

3.Fill with fuel to proper level.

4.Clean free of all debris.

5.Service spark plug.

6.Replace fuel filter.

7.Drain and clean fuel system.

1.Lessen load.

2.Clean or replace filters.

3.Service spark plug.

4.Drain and clean fuel system.

5.Clean all debris from engine cooling screen.

1.Set throttle control to “SLOW” and allow engine to idle. Then, turn key to “OFF”.

(Trouble Shooting Continued on Next Page)

27

23

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Model Number Explanation ScramblerFrom Previous Column Protection for ChildrenProtection Against Tipovers PreparationOperation Safe Handling of GasolineTowing MaintenanceTable of Contents Nomenclature IntroductionMotion Control Levers Cutting Deck Adjustment Handle Forward of Operator SeatEngine Speed & Choke Control Right Control Panel Parking Brake Next to Left Control Panel Applies park brakePRE-START Check List Engine Operation 2.2.1. Starting EngineStopping Engine Reverse Motion Motion ControlGetting Ready Forward MotionStopping Motion Conventional TurningLeft turn shown right turn opposite ZERO-TURNINGMower Blade Disengagement Mower Operation Cutting Height AdjustmentMower Blade Engagement Mowing OperationsEngine Must not Start if Engine should Start ifEngine Must Begin to Stop if Single Blade Deck Service After First 5 HoursChange Engine OIL Check Mower BladeEngine Oil Oil Filter Air Filter Service Every 25 Operating HoursChecking Mower Belt Tension Engine Engine Cooling SystemUnderside View of 33 Deck Check EngineMower Components LubricationMotion Control Pivot Bushings Front Wheel BearingsFront Caster Wheel Pivot Shaft Parking Brake Pivot BushingsStorage OUT of Season Service AnnuallyMotion Control Adjustments Neutral AdjustmentsTracking Adjustments Deck Engine Adjustments & RepairMower Drive Belt Adjustment Belt ReplacementIdler ARM and Belt Guide Detail Blade Brake AdjustmentBelt Replacements From Previous+ 1/16 From Previous Page Checking the 33 Deck BladeDeck Shown Front or Rear View of DeckMower Deck Timing ROD Front to Rear Deck Pitch 38 DecksWheel Brake Adjustment Mower Blade Replacement 4.5.1. Blade Wear LimitsBlade Sharpening Battery Service Blade Replacement ChartMower Blade Replacement 4.5.3. Blade Replacement Battery Battery RemovalNEW Battery Preparation 1. Remove battery from carton Battery TestingProblem Probable Cause Trouble Shooting on NextCorrective Action Excessive Vibration Problem Probable Cause Corrective ActionUSE HRS Season Service Performed EachMAINTENANCE/REPLACEMENT Parts 100Decal Identification European Noise Control Decal Disclaimer of Warranty Year Limited WarrantyPage Page Page Scrambler ZERO-TURN Hydro Drive European Model Series

ESZT18336BVE specifications

The Snapper ESZT18336BVE is a cutting-edge electric lawn mower designed for homeowners seeking efficiency, power, and ease of use. This innovative model integrates advanced technologies and features that enhance the mowing experience while ensuring a high-quality finish on various lawn types.

One of the standout features of the Snapper ESZT18336BVE is its powerful 36V lithium-ion battery system. This robust power source provides extended run time, allowing users to cover larger areas without the hassle of cords or frequent recharging. The battery is designed for quick charging, ensuring that the mower is ready when you are. Its energy-efficient operation not only reduces electricity costs but also contributes to a cleaner environment by emitting no harmful emissions.

The ESZT18336BVE boasts a versatile 18-inch cutting deck, ideal for small to medium-sized lawns. This size strikes a perfect balance between maneuverability and efficiency, enabling users to navigate around obstacles and corners with ease. The adjustable cutting height feature provides six different settings, ranging from 1 to 3.5 inches, allowing users to achieve their desired lawn height and adapt to varying grass types and seasonal growth.

Ergonomics play a significant role in the design of the Snapper ESZT18336BVE. The mower is equipped with a comfortable handle that can be adjusted to different heights, catering to users of varying statures while reducing strain during operation. The lightweight design further enhances ergonomics, making it easy to lift and transport.

Safety is paramount in the design of the Snapper ESZT18336BVE, featuring a reliable safety key that prevents accidental starting. Additionally, the mower integrates a blade brake system that stops the blade quickly when the user releases the control handles, providing peace of mind during operation.

The Snapper ESZT18336BVE also incorporates innovative mowing technologies, including a 3-in-1 mulching system that allows users to mulch, bag, or discharge grass clippings. This flexibility enables the efficient disposal of lawn waste and contributes to a healthier lawn by returning nutrients back into the soil.

In summary, the Snapper ESZT18336BVE combines power, convenience, and user-centric design. Its advanced battery technology, adjustable cutting deck, ergonomic features, and smart safety mechanisms make it an excellent choice for homeowners who prioritize performance and sustainability in their lawn care routine.
Top Page Image Contents