Snapper EM250821BE, EM281021BE Interlock System, Lubrication Grease Fittings, Battery Fluid Level

Page 17

Section 3 - MAINTENANCE

3.2.7. INTERLOCK SYSTEM

Check interlock controls for proper function:

The engine MUST NOT start if:

1.Blade Control is “ON” and/or clutch/brake pedal is released.

The engine and blades MUST STOP if:

2.The operator leaves the operator position with Blade Control “ON” and/or clutch/brake pedal is released.

WARNING

DO NOT operate machine if interlock system is not functioning properly. Contact your SNAPPER dealer immediately for assistance.

3.2.8. REVERSE LOCKOUT MECHANISM

Check function of Reverse Lockout Mechanism with engine off.

1.Depress and hold blade pedals.

2.Depress and hold clutch/brake pedal.

3.Shift lever must not go into reverse.

WARNING

DO NOT operate machine if Reverse Lockout Mechanism is not functioning properly. Contact your SNAPPER dealer immediately for assistance.

3.2.9. LUBRICATION – GREASE FITTINGS

The following components on the Rear Engine Rider are equipped with grease fittings and require periodic lubrication. Apply General Purpose grease (NLGI No.2) with a grease gun.

1.Front Wheel Bearings. Refer to Section “FRONT WHEEL BEARINGS – LUBRICATION”.

2.Rear Axle Bearing. Refer to Section “REAR AXLE BEARING – LUBRICATION”.

3.Mower Blade Spindle. Refer to Section “MOWER BLADE SPINDLE – LUBRICATION”.

3.3SERVICE - EVERY 25 OPERATING HOURS

3.3.1.Perform all service required after the first 5 hours of operation. Refer to Section “SERVICE – AFTER 5 HOURS”.

3.3.2.BATTERY FLUID LEVEL

1.Remove battery. Refer to Section “BATTERY REMOVAL”.

2.Remove battery caps. Check fluid level.

3.Add water only to bring fluid to proper level – approximately 3/16” above plates.

DO NOT OVERFILL.

4.Reinstall battery. Refer to Section “BATTERY INSTALLATION”.

3.3.3. MOWER DECK LEVELNESS

Check mower deck for proper level. Adjust as required. Refer to Section “MOWER DECK ADJUSTMENT – LEVELNESS”.

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage.

3.3.4. CLEAN MOWER DECK

1.Follow WARNING statement found on this page.

2.Check fuel level in tank. If over 3/4 full, remove tank. Refer to Section “REMOVING FUEL TANK”. If 3/4 or less, proceed to next step.

3.Carefully stand Rear Engine Rider on rear bumper.

4.Clean underside of mower deck, removing all accumulation of grass clippings and debris.

5.Clean top of deck, removing all grass clippings and debris.

3.3.5MOWER BLADE SPINDLE - LUBRICATION 1. Follow WARNING statement found on this page.

2. Check fuel level in tank. If over 3/4 full, remove tank. Refer to Section “FUEK TANK REMOVAL”. If 3/4 or less, proceed to next step.

3. Carefully stand Rear Engine Rider on rear bumper.

4. Lubricate spindle with three shots of general purpose grease from grease gun. See Figure 3.5.

IMPORTANT: If the Rear Engine Rider will be on its rear bumper for longer than two hours, remove the battery. Refer to Section “BATTERY REMOVAL”.

3.3.6.MOWER DECK LINKAGE - LUBRICATION Lubricate all mower deck linkage pivot points with a light coat of motor oil.

SPINDLE

GREASE

FITTING

FIGURE 3.5

(Continued on next page)

17

Image 17
Contents Manual No -3545 I.R /29/00 European Rear Engine Riding Mower SeriesImportant Safety Instructions Operation Table of Contents Nomenclature IntroductionFamiliarization Decals / Symbols Lowest Traction Height CUT Clutch PRE-START Check List OPERATOR’S Seat Adjustment 2.2.1. Front to Rear AdjustmentOn Next Starting & Operation Engine Electric StartEngine Manual Start Starting & OperationEngine Electric Start Wheel Drive Starting & Operation 2.3.3. Mower BladeMower Blade Stopping ENGINE, Wheel DRIVE, Blade 2.4.1. EngineDo not park machine on slopes Cutting Height AdjustmentStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Reverse Lockout Mechanism Override Reverse Lockout MechanismService Engine AIR Cleaner Check Mower Blade Service After First 5 Hours Change Engine OILBlade Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltService Brake / Park Brake Battery Fluid Level Service Every 25 Operating HoursClean Mower Deck Interlock SystemRear Axle Bearing Lubrication Service Every 25 Operating Hours from previousFront Wheel Bearing Lubrication Engine Service AnnuallyFuel Filter Every TWO YearsRemoving Fuel Tank Storage OUT of SeasonMower Drive Belt Adjustment for 25, 28 & 30 M Models Engine Adjustments & RepairMower Deck Adjustment Side-To-Side Levelness Blade Brake AdjustmentFront to Rear Levelness 30 Decks Mower Deck AdjustmentFront to Rear Levelness 25 & 28 Decks Chain Case Clutch Yoke Cable Housing Spring Blade Sharpening Mower Blade Replacement 4.4.1. Blade Wear LimitsBelt Removal Blade Drive Belt ReplacementBelt Replacement Battery Installation Battery Battery RemovalBattery Storage Battery ServiceNEW Battery Preparation 1. Remove battery from carton Battery TestingSnapper Rear Engine Rider Accessories Stop Problem Probable Cause Corrective ActionBlades Not Cutting Loss Of TractionCutting Grass ImproperlyTo be Performed Pages Subject Service ReferenceMAINTENANCE/REPLACEMENT Parts Maintenance Parts Disclaimer of Warranty Year Limited WarrantyService Notes Service Notes European Rear Engine Riding Mower Series

EM250821BE, EM281021BE specifications

The Snapper EM250821BE and EM281021BE models are two versatile battery-powered mowers designed to meet the diverse needs of homeowners and landscape professionals alike. These electric mowers are characterized by their user-friendly design, robust performance, and advanced technology, making them ideal for efficient lawn care.

One of the standout features of the Snapper EM250821BE is its 21-inch cutting deck, which ensures a wide mowing path and allows users to cover more ground in less time. This model is equipped with a powerful 82V battery system that delivers consistent voltage and runtime for large, demanding yards. With a simple push of a button, users can engage the motor, eliminating the hassle of pull-starts commonly associated with gas mowers.

The EM281021BE, on the other hand, boasts a slightly larger 28-inch cutting deck, which is designed for even greater efficiency. With its dual-blade technology, this mower not only provides a clean, precise cut but also enhances grass mulching capabilities, returning nutrients back to the lawn. Both models feature adjustable cutting heights, allowing users to customize the mower settings to suit different grass types and desired lawn appearances.

Another key technology incorporated in both mowers is the Smart Drive self-propulsion system. This system responds to the user’s walking speed, enabling effortless maneuverability across various terrains. With variable speed settings, operators can maintain control over their mowing pace, whether navigating tight corners or cruising down wide-open fields.

Ergonomically designed handles improve user comfort, and the foldable design enhances convenience for storage and transportation. A quick-release handle makes it easy to adjust the mower's height, accommodating users of all sizes and ensuring comfortable operation.

Both Snapper EM250821BE and EM281021BE are equipped with high-efficiency brushless motors that reduce noise and vibrations, resulting in a quieter mowing experience. Furthermore, their maintenance-free design means that users won’t have to deal with oil changes or spark plug replacements, making them environmentally friendly alternatives to traditional gas mowers.

In conclusion, the Snapper EM250821BE and EM281021BE mowers combine modern technology, ease of use, and powerful performance to deliver exceptional results. Whether for residential or professional use, these models are designed to meet the growing demand for sustainable lawn care solutions while maintaining the high standards that Snapper is known for.