Snapper EM250821BE, EM281021BE important safety instructions Operation

Page 3

IMPORTANT SAFETY INSTRUCTIONS

PREPARATION

(Continued From Previous Page)

7.Keep people and pets out of mowing area. Immediately STOP blades, STOP engine, and STOP machine if anyone enters the area.

8.Check shields, deflectors, switches, blade controls and other safety devices frequently for proper operation and location.

9.Make sure all safety decals are clearly legible. Replace if damaged.

10.Protect yourself when mowing and wear safety glasses, long pants and substantial footwear.

11.Know how to STOP blades and engine quickly in preparation for emergencies.

12.Use extra care when loading or unloading the machine into a trailer or truck.

13.Check grass catcher components frequently for signs of wear or deterioration and replace as needed to prevent injury from thrown objects going through weak or worn spots.

OPERATION

1.Mount and dismount machine from left side.

2.Start engine from operator's seat, if possible. Make sure blades are OFF and parking brake is set.

3.DO NOT leave machine with engine running. STOP engine, STOP blades, SET brake, and Remove key before leaving operators position of any reason.

4.DO NOT operate machine unless properly seated with feet on feet rests or pedal(s).

5.STOP BLADES and ENGINE and make sure blades have stopped before removing grass catcher or unclogging mower to prevent loss of fingers or hand.

6.Blades must be OFF except when cutting grass. Set blades in highest position when mowing over rough ground.

7.Keep hands and feet away from rotating blades underneath deck. DO NOT place foot on ground while BLADES are ON or machine is in motion.

8.DO NOT operate machine without entire grass catcher or guards in place. DO NOT point discharge at people, passing cars, windows or doors.

9.Slow down before turning.

10.Watch out for traffic when near or crossing roadways.

11.STOP engine immediately after striking an obstruction. Inspect machine and repair damage before resuming operation.

12.Operate machine only in daylight or with good artificial light.

13.Move joystick (if equipped) SLOWLY to maintain control during speed and directional changes.

OPERATION

(Continued From Previous Column)

14.Exercise CAUTION when pulling loads. Limit loads to those you can safely control and attach loads to hitch plate as specified with SNAPPER attachment instructions.

15.DO NOT operate engine in enclosed areas. Engine exhaust gases contain carbon monoxide, a deadly poison.

MAINTENANCE

1.DO NOT store machine or fuel container inside where fumes may reach an open flame, spark or pilot light such as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of the reach of children in a well ventilated, unoccupied building.

2.Keep engine free of grass, leaves or excess grease to reduce fire hazard and engine overheating.

3.When draining fuel tank, drain fuel into an approved container outdoors and away from open flame.

4.Check brakes frequently; adjust, repair or replace as needed.

5.Keep all bolts, nuts and screws properly tight. Check that all cotter pins are in proper position.

6.Always provide adequate ventilation when running engine. Exhaust gases contain carbon monoxide, an odorless and deadly poison.

7.Disconnect negative (black) cable from battery before performing maintenance or service. Cranking engine could cause injury.

8.DO NOT work under machine without safety blocks.

9.Service engine and make adjustments only when engine is stopped. Remove spark plug wire(s) from spark plug(s) and secure wire(s) away from spark plug(s).

10.DO NOT change engine governor speed settings or overspeed engine.

11.Lubricate machine at intervals specified in manual to prevent controls from binding.

12.Mower blades are sharp and can cut. Wrap the blades or wear heavy leather gloves and use CAUTION when handling them.

13.DO NOT test for spark by grounding spark plug next to spark plug hole; spark plug could ignite gas exiting engine.

14.Have machine serviced by an authorized SNAPPER dealer at least once a year and have the dealer install any new safety devices.

15.Use only genuine SNAPPER replacement parts to assure that original standards are maintained.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Manual No -3545 I.R /29/00 European Rear Engine Riding Mower SeriesImportant Safety Instructions Operation Table of Contents Nomenclature IntroductionFamiliarization Decals / Symbols Lowest Traction Height CUT Clutch PRE-START Check List OPERATOR’S Seat Adjustment 2.2.1. Front to Rear AdjustmentOn Next Starting & Operation Engine Electric StartStarting & Operation Engine Electric StartEngine Manual Start Wheel Drive Starting & Operation 2.3.3. Mower BladeMower Blade Stopping ENGINE, Wheel DRIVE, Blade 2.4.1. EngineCutting Height Adjustment Stopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park BrakeDo not park machine on slopes Reverse Lockout Mechanism Override Reverse Lockout MechanismService Engine AIR Cleaner Check Mower Blade Service After First 5 Hours Change Engine OILService After First 5 Hours 3.2.4. Check Blade Drive Belt Service Brake / Park BrakeBlade Brake Interlock System Service Every 25 Operating HoursBattery Fluid Level Clean Mower DeckService Every 25 Operating Hours from previous Front Wheel Bearing LubricationRear Axle Bearing Lubrication Every TWO Years Service AnnuallyEngine Fuel FilterRemoving Fuel Tank Storage OUT of SeasonMower Drive Belt Adjustment for 25, 28 & 30 M Models Engine Adjustments & RepairMower Deck Adjustment Side-To-Side Levelness Blade Brake AdjustmentMower Deck Adjustment Front to Rear Levelness 25 & 28 DecksFront to Rear Levelness 30 Decks Chain Case Clutch Yoke Cable Housing Spring Blade Sharpening Mower Blade Replacement 4.4.1. Blade Wear LimitsBlade Drive Belt Replacement Belt ReplacementBelt Removal Battery Installation Battery Battery RemovalBattery Testing Battery ServiceBattery Storage NEW Battery Preparation 1. Remove battery from cartonSnapper Rear Engine Rider Accessories Stop Problem Probable Cause Corrective ActionImproperly Loss Of TractionBlades Not Cutting Cutting GrassTo be Performed Pages Subject Service ReferenceMAINTENANCE/REPLACEMENT Parts Maintenance Parts Disclaimer of Warranty Year Limited WarrantyService Notes Service Notes European Rear Engine Riding Mower Series

EM250821BE, EM281021BE specifications

The Snapper EM250821BE and EM281021BE models are two versatile battery-powered mowers designed to meet the diverse needs of homeowners and landscape professionals alike. These electric mowers are characterized by their user-friendly design, robust performance, and advanced technology, making them ideal for efficient lawn care.

One of the standout features of the Snapper EM250821BE is its 21-inch cutting deck, which ensures a wide mowing path and allows users to cover more ground in less time. This model is equipped with a powerful 82V battery system that delivers consistent voltage and runtime for large, demanding yards. With a simple push of a button, users can engage the motor, eliminating the hassle of pull-starts commonly associated with gas mowers.

The EM281021BE, on the other hand, boasts a slightly larger 28-inch cutting deck, which is designed for even greater efficiency. With its dual-blade technology, this mower not only provides a clean, precise cut but also enhances grass mulching capabilities, returning nutrients back to the lawn. Both models feature adjustable cutting heights, allowing users to customize the mower settings to suit different grass types and desired lawn appearances.

Another key technology incorporated in both mowers is the Smart Drive self-propulsion system. This system responds to the user’s walking speed, enabling effortless maneuverability across various terrains. With variable speed settings, operators can maintain control over their mowing pace, whether navigating tight corners or cruising down wide-open fields.

Ergonomically designed handles improve user comfort, and the foldable design enhances convenience for storage and transportation. A quick-release handle makes it easy to adjust the mower's height, accommodating users of all sizes and ensuring comfortable operation.

Both Snapper EM250821BE and EM281021BE are equipped with high-efficiency brushless motors that reduce noise and vibrations, resulting in a quieter mowing experience. Furthermore, their maintenance-free design means that users won’t have to deal with oil changes or spark plug replacements, making them environmentally friendly alternatives to traditional gas mowers.

In conclusion, the Snapper EM250821BE and EM281021BE mowers combine modern technology, ease of use, and powerful performance to deliver exceptional results. Whether for residential or professional use, these models are designed to meet the growing demand for sustainable lawn care solutions while maintaining the high standards that Snapper is known for.
Top Page Image Contents