Snapper ELT180H33IBV Introduction, Service After First 5 Hours, Change Engine OIL

Page 15

Section 3 - MAINTENANCE

3.1 INTRODUCTION

To retain the quality of the Tractor, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular Tractor, always mention the model and serial number. SNAPPER recommends returning the Tractor to an authorized SNAPPER dealer annually for inspection and addition of any new devices, which might upgrade the safety of the Tractor. For the nearest SNAPPER dealer in your area, check the yellow pages under the heading LAWN MOWERS. For engine parts and service, look for the engine manufacturer’s dealers under the heading, ENGINES - gasoline.

3.2 SERVICE - AFTER FIRST 5 HOURS

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

3.2.1. CHANGE ENGINE OIL

These model tractors are equipped Fastex™ oil drains.

1.Rotate drain body counterclockwise and pull out to open drain. See Figure 3.1.

2.Drain oil into a 2 quart container placed beneath end of oil drain.

3.After all oil has drained, push drain body "IN" and rotate clockwise to close.

4.Fill engine with new motor oil as specified in engine owner's manual.

WARNING

The following procedure requires the engine and blades to be operated. Exercise extreme caution. Clear area of loose parts & tools first. Only operate blades when seated in the operator’s seat.

3.2.2. CHECK BLADE BRAKE

1.Check blade brake for proper function. Blades should stop rotating in 5 seconds or less after moving the blade engagement lever down to the OFF position.

2.If blades continue to rotate longer than 5 seconds do not operate machine. Refer to Section “BLADE BRAKE ADJUSTMENT” or contact your SNAPPER dealer for assistance.

3.2.3. CHECK MOWER BLADE

1.Remove deck from tractor.

2.Carefully position deck to access blade.

3.Check blade for sharpness, wear and damage. Refer to Section “BLADE WEAR LIMITS”.

4.Check blade for straightness. Refer to Section

“ADJUSTING MOWER BLADE”.

5.Check torque of blade mounting bolts.

Torque 33" deck to: - 30 to 40 ft lbs. See Figure 3.2.

OIL

FILLER

TUBE

FASTEX™

OIL DRAIN

ROTATE COUNTER-

CLOCKWISE AND PULL OUT

TO OPEN.

PUSH IN AND ROTATE

CLOCKWISE TO CLOSE.

FIGURE 3.1

TORQUE 33” BLADE TO 30 TO 40 FT. LBS.

FIGURE 3.2

WARNING

Blades must stop rotating in 5 seconds or less after blades have been turned off. DO NOT operate machine until blade brake has been repaired and functioning properly. Contact your SNAPPER dealer for assistance.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 180 Model Number ExplanationImportant Safety Instructions Important Safety Instructions Towing Table of Contents Controls FamiliarizationFamiliarization Decals / Symbols Lights on Engine OFF OPERATOR’S Seat Adjustment Front to Rear Adjustment PRE-START ChecklistOFF Starting & Operation Starting EngineStopping Wheel Drive Starting & Operation 2.3.2. Starting Wheel DriveStarting Mower Blade Stopping ENGINE, BLADE, Wheel Drive 2.4.1 Stopping EngineReleasing Park Brake Setting Park BrakeCutting Height Adjustment Stopping Stopping Mower BladeRolling Tractor with Engine OFF Rolling Hydro Models Reverse Lockout Mechanism Override Reverse Lockout MechanismCheck Blade Brake Service After First 5 HoursIntroduction Change Engine OILService Every 25 Operating Hours Check Engine Check Deck Drive BeltMower Components Tractor Lubrication Fuel Filter Annually END of Each SeasonEngine should Start if Annually END of Each Season 3.4.2. Fuel FilterSpark Plug Hydrostatic Transmission OIL Engine Must not Start ifEngine Adjustments & Repair Blade Brake AdjustmentOn next Adjusting Mower Blade 33 Decks Only Blade Belt Adjustment 33 Deck from previousSide View of Deck Deck Level Adjustment Side to Side Deck Level Adjustment Side to Side Deck Level Adjustment Front to Rear Sector PlatesDeck Level Adjustment Front to Rear Front Lift ROD Tractor Drive Components 4.3.1. Brake Adjustment Steering AdjustmentShifter Adjustment Mower Blade Service Standard Blade Wear Limits Ninja Blade Sharpening Mower Blade ReplacementNinja Blade Wear Limits Standard Blade SharpeningTraction drive belt removal Mower Blade ReplacementTraction Drive Belt Replacement Mower Deck RemovalTraction drive belt replacement Traction drive belt removal from previousView from Underneath Tractor Traction drive belt replacement from previous Deck Belt Removal & ReplacementDeck Drive Belt Battery Storage Battery Battery RemovalBattery Installation Battery ServiceNEW Battery Preparation Battery TestingAvailable ELT150H33IBV Accessories Available AccessoriesElectrical System Schematics Briggs & Stratton with Lights Corrective Action Problem Probable CauseTractor Will Not 1. Speed control handle in the neutral N PositionEngine speed too slow Maintenance Parts Disclaimer of Warranty Year Limited WarrantyService Notes European Lawn Tractor Hydrostatic Drive Series

ELT180H33IBV specifications

The Snapper ELT180H33IBV is an exceptional lawn mower designed for efficiency and ease of use, making it an ideal choice for homeowners looking to maintain their lawns with minimal effort. This mower is part of Snapper’s reputation for producing reliable and high-performance outdoor power equipment, delivering a robust solution for lawn care enthusiasts.

One of the standout features of the ELT180H33IBV is its powerful engine. It is equipped with a 180cc Briggs & Stratton engine, providing ample horsepower to tackle various mowing tasks with ease. This engine is designed for efficiency, ensuring that users can mow larger areas without frequent refueling, which significantly enhances productivity during mowing sessions.

The Snapper ELT180H33IBV features a 33-inch cutting deck, making it compact yet efficient. The size allows for maneuverability in tight spaces, such as flower beds and garden edges, while still covering enough ground to make mowing quicker. The cutting deck height is easily adjustable, offering multiple height settings to achieve the desired grass length, which adds versatility to accommodate different types of lawns.

In terms of technology, the ELT180H33IBV is equipped with a user-friendly starting system. The mower features an easy pull-start mechanism, and the engine is designed to start with minimal effort, ensuring that users can quickly get to work without frustration.

Another important characteristic of this mower is its durability. Snapper has built this model with high-quality materials to withstand the rigors of outdoor use. The rugged construction ensures long-lasting performance, significantly reducing the need for frequent repairs or replacements.

For added convenience, the Snapper ELT180H33IBV incorporates a rear bagging system, which collects clippings for easy disposal. By using the bagging option, homeowners can keep their lawns looking neat and tidy without the hassle of raking.

Moreover, the mower comes with comfortable handles that provide a secure grip, enhancing overall control during operation. This ergonomic design reduces fatigue, making it easier to maneuver the mower over extended periods.

In summary, the Snapper ELT180H33IBV is a well-rounded mower that combines power, versatility, and user-friendly features, making it suitable for those who want an efficient solution for lawn maintenance. With its high-performance engine, compact design, and durable build, it stands out as a reliable choice for homeowners aiming to achieve a pristine lawn with ease.
Top Page Image Contents