Snapper ELT180H33IBV Tractor Drive Components 4.3.1. Brake Adjustment, Steering Adjustment

Page 24

Section 4 - ADJUSTMENT & REPAIR

4.3TRACTOR DRIVE COMPONENTS 4.3.1. BRAKE ADJUSTMENT

1.To be properly adjusted, the brake should stop the tractor in approximately 6 feet from top speed when the clutch/brake pedal is fully depressed.

2.Adjust brake when necessary as follows:

3.Turn engine “OFF”. Remove key.

4.Locate brake adjustment nut underneath the rear of tractor. See Figure 4.13.

5.Turn nut clockwise to increase braking action or counterclockwise to decrease braking action.

6.Start engine and test brake.

7.Continue adjustment as described above until proper adjustment is achieved.

ROTATE TO LESSEN “PLAY”

FUEL TANK

ECCENTRIC MOUNTING NUT

ROTATE ADJUSTING NUT CLOCKWISE TO

INCREASE BRAKING OR COUNTER

CLOCKWISE TO DECREASE BRAKING

FIGURE 4.13

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

4.3.2STEERING ADJUSTMENT

Should excessive “Play” be noted in the steering, adjust as follows:

1.Turn engine “OFF”. Remove key.

2.From left side of tractor, locate the steering sector below fuel tank. See Figure 4.14.

FIGURE 4.14

3.Loosen the eccentric mounting nut and rotate the eccentric clockwise until steering “Play” is reduced. Refer back to Figure 4.14.

4.Tighten eccentric mounting nut.

4.3.3.SHIFTER ADJUSTMENT

The shift linkage is set at the factory and should not require further adjustment. The shifter is adjusted properly when the speed control lever can be placed at rear edge of the neutral detent and the tractor remains absolutely stationary. If motion is detected, neutral adjustment will be required. DO NOT operate a machine that creeps when shifted to neutral.

1.Stop engine. Remove key.

2.Move speed control lever to rear edge of neutral detent and hold firmly.

3.Locate neutral adjustment nut underneath the right rear of the tractor. See Figure 4.15

4.Turn the neutral adjustment nut 1/4 turn clockwise to reduce FORWARD creep. Turn the adjustment nut 1/4 turn counter clockwise to reduce Reverse creep. Only turn the adjustment nut in 1/4 turn increments.

5.Check for creep in neutral. Start engine. Move speed control lever to rear edge of the neutral detent. Machine should not move. If further adjustment is required, stop engine and repeat Step 4.

WARNING

DO NOT adjust shift linkage with engine running. The adjustment requires hands to be close to rotating parts. STOP engine. REMOVE key.

(Continued on next page)

24

Image 24
Contents Model Number Explanation 180Important Safety Instructions Important Safety Instructions Towing Table of Contents Familiarization ControlsFamiliarization Decals / Symbols Lights on Engine OFF PRE-START Checklist OPERATOR’S Seat Adjustment Front to Rear AdjustmentStarting & Operation Starting Engine OFFStarting & Operation 2.3.2. Starting Wheel Drive Starting Mower BladeStopping ENGINE, BLADE, Wheel Drive 2.4.1 Stopping Engine Stopping Wheel DriveSetting Park Brake Cutting Height AdjustmentStopping Stopping Mower Blade Releasing Park BrakeRolling Tractor with Engine OFF Rolling Hydro Models Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideService After First 5 Hours IntroductionChange Engine OIL Check Blade BrakeService Every 25 Operating Hours Check Engine Check Deck Drive BeltMower Components Tractor Lubrication Annually END of Each Season Fuel FilterAnnually END of Each Season 3.4.2. Fuel Filter Spark Plug Hydrostatic Transmission OILEngine Must not Start if Engine should Start ifEngine Adjustments & Repair Blade Brake AdjustmentOn next Blade Belt Adjustment 33 Deck from previous Adjusting Mower Blade 33 Decks OnlySide View of Deck Deck Level Adjustment Side to Side Deck Level Adjustment Side to Side Deck Level Adjustment Front to Rear Sector PlatesDeck Level Adjustment Front to Rear Front Lift ROD Tractor Drive Components 4.3.1. Brake Adjustment Steering AdjustmentShifter Adjustment Mower Blade Service Standard Blade Wear Limits Mower Blade Replacement Ninja Blade Wear LimitsStandard Blade Sharpening Ninja Blade SharpeningMower Blade Replacement Traction Drive Belt ReplacementMower Deck Removal Traction drive belt removalTraction drive belt replacement Traction drive belt removal from previousView from Underneath Tractor Traction drive belt replacement from previous Deck Belt Removal & ReplacementDeck Drive Belt Battery Battery Removal Battery InstallationBattery Service Battery StorageBattery Testing NEW Battery PreparationAvailable Accessories Available ELT150H33IBV AccessoriesElectrical System Schematics Briggs & Stratton with Lights Problem Probable Cause Corrective ActionTractor Will Not 1. Speed control handle in the neutral N PositionEngine speed too slow Maintenance Parts Year Limited Warranty Disclaimer of WarrantyService Notes European Lawn Tractor Hydrostatic Drive Series

ELT180H33IBV specifications

The Snapper ELT180H33IBV is an exceptional lawn mower designed for efficiency and ease of use, making it an ideal choice for homeowners looking to maintain their lawns with minimal effort. This mower is part of Snapper’s reputation for producing reliable and high-performance outdoor power equipment, delivering a robust solution for lawn care enthusiasts.

One of the standout features of the ELT180H33IBV is its powerful engine. It is equipped with a 180cc Briggs & Stratton engine, providing ample horsepower to tackle various mowing tasks with ease. This engine is designed for efficiency, ensuring that users can mow larger areas without frequent refueling, which significantly enhances productivity during mowing sessions.

The Snapper ELT180H33IBV features a 33-inch cutting deck, making it compact yet efficient. The size allows for maneuverability in tight spaces, such as flower beds and garden edges, while still covering enough ground to make mowing quicker. The cutting deck height is easily adjustable, offering multiple height settings to achieve the desired grass length, which adds versatility to accommodate different types of lawns.

In terms of technology, the ELT180H33IBV is equipped with a user-friendly starting system. The mower features an easy pull-start mechanism, and the engine is designed to start with minimal effort, ensuring that users can quickly get to work without frustration.

Another important characteristic of this mower is its durability. Snapper has built this model with high-quality materials to withstand the rigors of outdoor use. The rugged construction ensures long-lasting performance, significantly reducing the need for frequent repairs or replacements.

For added convenience, the Snapper ELT180H33IBV incorporates a rear bagging system, which collects clippings for easy disposal. By using the bagging option, homeowners can keep their lawns looking neat and tidy without the hassle of raking.

Moreover, the mower comes with comfortable handles that provide a secure grip, enhancing overall control during operation. This ergonomic design reduces fatigue, making it easier to maneuver the mower over extended periods.

In summary, the Snapper ELT180H33IBV is a well-rounded mower that combines power, versatility, and user-friendly features, making it suitable for those who want an efficient solution for lawn maintenance. With its high-performance engine, compact design, and durable build, it stands out as a reliable choice for homeowners aiming to achieve a pristine lawn with ease.