Snapper CP215019KW, CP215519HV, CP216019KWV, CP215519HV Problem Probable Cause, Corrective Action

Page 21

TROUBLESHOOTING

PROBLEM

 

PROBABLE CAUSE

Engine Will Not Start

1. Fuel tank empty.

Using Recoil Starter

2. Engine needs choking.

 

 

 

 

3.

Spark plug wire disconnected.

 

4.

Fuel Shut-Off in the “OFF” position

Engine Stalls or Stops

1. Blade control is released or is not being held securely

After Running

 

against handle.

 

2.

Engine Throttle Control in “Choke” position.

 

3.

Fuel tank empty.

 

4.

Engine air pre-cleaner and or air cleaner dirty.

 

5.

Spark plug defective or gap set improperly.

 

6.

Water, debris or stale fuel in fuel system.

 

7.

Fuel Shut-Off in the “OFF” position

Engine Loses Power

1. Engine air pre-cleaner or air cleaner dirty

 

2.

Spark plug faulty.

 

3.

Water, debris or stale fuel in fuel system.

Excessive Vibration

1. Damaged, out of balance or bent mower blade.

 

2.

Loose blade components.

 

3.

Loose or missing air lift (if equipped).

 

4.

Lumpy or frayed belt

Mower Will Not Move

1. Damaged transmission

Loss Of Traction

2. Traction drive belt requires replacement

(Self-Propelled Models)

3. Driven disc slipping

Cutting Grass

1. Cutting height too low or high.

Improperly

2. Engine speed too slow.

 

3. Forward ground speed too fast.

 

4. Terraced cut, side to side.

 

5. Excessive deck pitch, front to rear.

 

6. Cutting blade dull or damaged.

Poor Grass Discharge

1. Engine speed too slow.

 

2. Forward speed too fast.

 

3. Grass is wet.

 

4. Excessively worn or damaged blade.

 

5. Build up of grass clippings and debris under deck.

 

6. Improper blade installed on deck.

 

7. Blade installed improperly on deck.

Oil Leaking

1. Leaking engine case.

 

 

 

CORRECTIVE ACTION

1.Fill fuel tank with fresh fuel.

2.Choke engine by moving Engine Throttle Control fully forward into “Choke” position. (Check Engine Manual for further instructions.)

3.Place spark plug wire onto spark plug.

4.Turn Fuel Shut-Off to “ON” position

1.Blade control should be held securely against handle at all times during operation of mower.

2.Move throttle back from choke position.

3.Fill with fuel to proper level.

4.Clean free of all debris.

5.Service spark plug.

6.Drain and clean fuel system.

7.Turn Fuel Shut-Off to “ON” position

1.Clean or replace filters.

2.Service spark plug.

3.Drain and clean fuel system.

1.Service mower blade.

2.Service and tighten loose parts.

3.Replace air lifts. Tighten to proper torque.

4.Replace belt.

1.Contact authorized SNAPPER dealer.

2.Replace traction drive belt.

3.Clean or replace driven disc rubber ring.

1.Adjust cutting height.

2.Move engine speed control to “FAST” position.

3.Move ground speed control to a slower speed.

4.Adjust height of cut with height adjust levers.

5.Adjust height of cut with height adjust levers.

6.Sharpen cutting edges or replace blade.

1.Move engine speed control to “FAST” position.

2.Move ground speed control to a slower speed.

3.Mow when grass is dry.

4.Service mower blade.

5.Clean deck.

6.Install proper SNAPPER blade.

7.Install blade properly.

1.Contact authorized SNAPPER dealer.

2.Check and tighten drain plug.

3.Make sure dip stick or oil filler cap is securely in place.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Steel Deck Walk Mowers Commercial Models Series Engine Designation Series Designation Engine Horse PowerImportant Safety Instructions From Previous Do not refuel the machine indoorsFrom Previous Column Important Safety Instructions Table of Contents Engine Speed Control IntroductionNomenclature Starting & Operation Engine & Blade PRE-START Check ListCutting Height Adjustment Handle Height AdjustmentPropelling Mower StoppingLatch Position Cutting Height Settings Removing and Dumping Grass Catcher Slide Closure Type Recycling Operation Dispose of drain oil properly Service After First 5 Hours 3.2.1. Change Engine OILStorage Procedure Service AnnuallyCheck Mower Blade Check Engine Drive BeltMower Blade Replacement Standard Blade Wear Limit Blade Sharpening1.A. Ninja Blade Wear Limit Wheel Drive Control Adjustment Cleaning Drive Disc & Driven Disc Driven and Drive Disc ServiceDrive Spring Repair/Replacement Driven Disc AdjustmentOn Next Replacing Driven Disc Rubber Ring Reassemble components in reverse order Remove bearing and replace with new bearingBelt Service Engine Drive Belt Replacement Stretch Type BeltsOn Next Pulley Position Reinstall blade hub and cutter bladeCorrective Action Problem Probable CauseMAINTENANCE/REPLACEMENT Parts Service Performed Each100 USE HRS SeasonDisclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page Page Steel Deck Walk Behind Mowers Commercial Models Series

CP215019KW, CP215519HV, CP216019KWV, CP215519HV specifications

The Snapper CP216019KWV, CP215519HV, CP215019KW, and CP215519HV models are robust lawn mowers designed to cater to various residential and professional mowing needs. Each model is built with cutting-edge technologies and features that enhance performance, durability, and user-friendliness.

The CP216019KWV is favored for its powerful 21-inch cutting deck that allows for efficient mowing over large areas. With a 190cc engine, it delivers reliable performance and impressive torque, ensuring that grass cutting is smooth and effortless. The adjustable cutting height provides users with the flexibility to achieve their desired lawn appearance, making it suitable for different grass types. Furthermore, it boasts a self-propelling mechanism which allows for easy maneuvering, especially on hilly terrains.

In contrast, the CP215519HV model stands out with its innovative Variable Speed Drive system. This feature enables the operator to adjust the mower's speed according to their walking pace, making it more comfortable to use over extended periods. The 21-inch deck is also designed for versatility, allowing for both bagging and mulching options, which enhances the mowing experience and benefits lawn health.

The CP215019KW is another model that focuses on efficiency and power. With a 150cc engine, this mower is lightweight yet formidable, providing enough power for residential yard maintenance. Its compact design makes it easy to store, while still offering features like an easy-start recoil and a durable steel deck that guarantees longevity. The integrated bagging system collects clippings neatly, keeping lawns tidy.

Finally, the CP215519HV model presents a balanced option with user-friendly features and a solid construction. It integrates a powerful engine that ensures consistent grass cutting capabilities and a quick-change height adjustment lever to transition seamlessly between different grass lengths. Its dual-lever height adjustment system enhances precision, allowing for custom cutting heights tailored to specific lawn requirements.

All four models are equipped with Snapper's commitment to quality, making them excellent choices for anyone looking to maintain a manicured lawn. With ergonomic designs, easy-to-use features, and durable construction, they provide powerful solutions for both novice and seasoned gardeners alike.
Top Page Image Contents