Snapper GP216512RV, C216012RV, GP215512KWV Familiarization, Figure, Introduction, Nomenclature

Page 5
Section 1 - FAMILIARIZATION

Section 1 - FAMILIARIZATION

WHEEL DRIVE

CONTROL

ENGINE SPEED

CONTROL

BLADE

CONTROL

GROUND

SPEED

CONTROL

UPPER

HANDLE

BAG

SLIDER

MID

HANDLE

GRASS

BAG

LOWER

HANDLE

REAR HEIGHT

ADJUSTMENT LATCH

WHEEL DRIVE CONTROL -

BLADE CONTROL -

RELEASE TO STOP

FORWARD MOTION

RELEASE TO STOP

 

BLADE AND ENGINE

GROUND

SPEED

FASTCONTROL

ENGINE

SPEED

CONTROLSLOW

ROPE START HANDLE

FUEL FILLER CAP

OIL FILL CAP &

DIPSTICK

KAWASAKI 4-CYCLE

OHV ENGINE

MUFFLER

ENGINE SPEED DECAL

“CHOKE”

“FAST”

“SLOW”

GRASS BAG

CONNECTOR

ENGINE AIR BREATHER COVER

BAG ADAPTER

CATCHER MODEL SHOWN (ROPE START MOUNTED ON LEFT SIDE OF HANDLE)

FRONT HEIGHT

ADJUSTING LATCH

MOWER DECK

FIGURE 1.1

1.1 INTRODUCTION

This manual has been prepared for the operators of the SNAPPER WALK BEHIND MOWERS. Its purpose, aside from recommending operating and routine service requirements, is to promote safety through the use of accepted operating practices.

Read, Understand and Follow the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 & 3 of this manual and all safety messages on the mower and attachments before operating the mower.

1.2 NOMENCLATURE

The nomenclature drawing above, Figure 1.1, shows the essential parts of the SNAPPER WALK BEHIND MOWERS. It is recommended that all operators of the mower become thoroughly familiar with the controls, parts and operation of the mower before operating. Specific details involving the engine are found in the separate engine owner’s manual. Study these manuals before operating and keep both handy for future reference.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents 21” STEEL DECK Safety Instructions & Operator’s Manual forWALK MOWERS COMMERCIAL MODEL SERIES PUSHPROTECTION FOR CHILDREN IMPORTANT SAFETY INSTRUCTIONSSLOPE OPERATION PREPARATIONOPERATION MAINTENANCE AND STORAGETABLE OF CONTENTS FIGURE Section 1 - FAMILIARIZATION1.1 INTRODUCTION 1.2 NOMENCLATURE2.2STARTING & OPERATION 2.2.1. ENGINE & BLADE Section 2 - OPERATING INSTRUCTIONS2.1PRE-STARTCHECK LIST 2.3 STOPPING 2.5CUTTING HEIGHT ADJUSTMENT2.4 HANDLE HEIGHT ADJUSTMENT 2.6RECYCLING OPERATION - OPTIONAL ACCESSORY 3.1INTRODUCTION Section 3 - MAINTENANCEROBIN ENGINES KAWASAKI ENGINESSection 3 – MAINTENANCE 3.3 SERVICE - ANNUALLY Section 4 - REPAIR & ADJUSTMENTS Continued on next page FIGURE 4.2WHEEL DRIVE CONTROL ADJUSTMENT4.3DRIVEN DISC SERVICE 4.3.1. Cleaning Drive Disc & Driven Disc 4.3.4. Replacing Driven Disc Rubber Ring FIGURE 4.3.6. Replacement Of Bearing On Pulley End Of FIGURE PROBLEM TROUBLESHOOTINGPROBABLE CAUSE CORRECTIVE ACTIONMAINTENANCE PARTS SERVICE SCHEDULE3 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE SERVICE NOTES SERVICE NOTES Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. Phone:
Top Page Image Contents