Snapper Complete Guide to Installing Your Mulching Cover Guard

Page 14
Operation

Mulching Operation

 

 

Installing the Discharge

 

For best mulching results, cut up to a maximum of 1/3

Deflector

 

 

of grass blade length and recycle ONLY when grass is

 

 

dry.

 

 

 

 

!

WARNING

!

1. Set all wheels in the highest cutting position (Notch

 

7). Refer to the Section entitled “Cutting Height

DO NOT attempt any maintenance, adjustments or

Adjustment”.

 

 

 

service with engine and blade running. STOP engine

2. Move the engine speed control to the fast (Rabbit)

and blade. Disconnect spark plug wire and secure

position.

 

 

 

away from spark plug. Engine and components are

3. Move the ground speed control to the slowest

 

HOT. Avoid serious burns, allow sufficient time for all

speed setting.

 

 

 

components to cool.

 

4. Proceed mowing slowly. If the grass is very dense,

1. Remove the mulching cover. Refer to the Section

lower each rear wheel latch one notch lower than

the front wheel latches to improve mulching perfor-

2.

entitled “Mulching Operation”.

 

mance.

 

 

 

Install the deflector (A, Figure 9) to the deck in

 

 

 

 

 

place of the mulching cover, making sure that:

NOTE: The mulching cover should remain on the

 

• The front hole (B) on the outside front of the

 

machine at all times, unless alternate discharge opera-

 

deflector fits over the stud where the front of the

tions are desired, such as side discharging or bagging.

 

mulching cover was originally secured;

 

 

 

 

 

• The slot (C) on top of the deflector slips under the

Removing the Mulching Cover

 

est aining nut on top of the deck (under the right

ont corner

f the e gi e);

 

(Optional Accessory on Some Models)

 

The slot (D)

n the inside rear of the deflector

!

WARNING

 

 

slips on o he s ud behind the rear of the discharge

! foropening, where the rear of the mulching cover was

DO NOT attempt any maintenance, adjustmen s

r

3.

originally se ured.

 

service with engine and blade running. STOP engine

Install the internal/external tooth lock washers and

and blade. Disconnect spark plug wire and secure

 

knob n ts onto the studs and tighten securely.

away from spark plug. Engine and components are

 

 

 

 

HOT. Avoid serious burns, allow sufficient time for all

 

 

C

B

components to cool.

 

 

 

 

1. Remove the knob nuts (A, Figure 8) and inter-

 

D

 

 

nal/external tooth lock washers (B) securing the

 

 

 

mulching cover (C) to the mower ck.

 

 

 

 

 

2. Remove the cover.

Reproduction

 

 

B

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 9: Installing the discharge deflector

 

 

 

 

 

 

!

WARNING

!

A

 

 

 

DO NOT operate without entire Grass Catcher or

C

 

 

guard in place. Grass Catcher components are

 

 

 

 

subject to deterioration during normal use. Inspect

Figure 8: Removing the mulching cover

 

frequently and replace worn or damaged components

 

immediately.

 

 

 

 

 

 

 

 

14

www.snapper.com

Image 14
Contents Reproduction Not ErenceTable of Contents Operator Safety Operating SafetyMoving Parts Ments. Know the controls and the proper use Ol. Clean sp lled fuel a d oil from machine. do notThis manual and on the mower, engine and attach Mower before startingThan a gasoline dispenser nozzle Disconnect and secure spark plug wire away from plugUse only an approved fuel container Container outdoors and away from open flameInstructions can result in serious bodily injury or Operator Safety Safety and Operation DecalsLowed. Not following these important warnings DeathExplanation of Safety Decals Explanation of Operation DecalsFeatures and Controls For Not Reprodu ctionBefore Starting Operation Oil RecommendationsFuel Recommendations Propelling the MowerStarting the Mower Stopping the Mower Cutting Height Adjustment Handle Height AdjustmentRemoving the Mulching Cover Mulching Operation Installing the DischargeDeflector Installing the mulching plug Operation Installing the Grass Bag NotMaintenance Maintenance Chart Emissions ControlChange Engine Oil Service Air Filter Not overfillStorage Procedure Check Safety Interlock SystemClean Debris Off Mower Fuel SystemCheck Grease Level in Transmission Maintenance ServiceCheck Mower Blade ReproductionCheck Engine Drive BeltMaintenance Mower Blade Replacement Blade SharpeningWheel Drive Control MaintenanceAdjustment Blade SharpeningDriven Disc Adjustment Maintenance Driven and Drive Disc ServiceDrive Spring Repair/Replacement Cleaning Drive Disc & Driven DiscDriven Disc Replacement Proper driven disc adjustmentDriven Disc Replacement Driven Disc Bearing Replacement Removing the driven disc assemblyReplacing the Bearing On the Pulley End Belt ServiceEngine Drive Belt Replacement Stretch Hex ShaftEngine Drive Belt Replacement Stretch Type Belts Ansmiss Ly-V Belt ReplacementFuel tank empty Fill fuel tank with fresh fuel TroubleshootingClean free of all debris Blade control is released or is not being heldLimited Warranty WarrantiesBriggs & Stratton Emissions Control Warranty Provisions Slope Guide Engine Power RatingMower Manuel dutilisation Machine Fontionnement Guide de conduite sur lesSécurité de lopérateur Accumulation de débris Pièces en mouvementObjets projetés Carburant et entretienPréparation Manipulation D’ESSENCE EN Toute Sécurité de lopérateur Étiquettes de sécurité et de FonctionnementReproduction Explication des étiquettes aut Llantes d’utilisationAvez des questions Fonctions et commandesCommande de régime moteur Commande d’entraînement Poignée à corde du démarreurAvant le démarrage Fontionnement Démarrer la tondeuse Déplacement de la tondeuseRecommandations de carburant Fontionnement Arrêter la tondeuse Réglage de la hauteur de CoupeDépose du couvercle de Opération de déchiquetage Installation du déflecteur’éjection DéchiquetagePose de la fiche de déchiquetage Fontionnement Installation du sac à herbe AvertissementEntretien Tableau de maintenance Contrôle démissionDu dépoussiéreur sur la partie inférieure des élé Entretien Changer lhuile moteur Entretien du filtre à airPient approprié. Éliminer l’huile usagée de façon appro Verrouillage de sécurité EntretienVérifier le système de Débarrassez la tondeuse deTransmission Vérifiez la lame de la tondeuseVérification du niveau de graisse de la Vérifiez la courroie d’entraînement duLimite dusure de lame NinjaReproduction Entretien Remplacement de lame de tondeuseLimite dusure de lame standard Aiguisage de lame Moteur saturera le filtre à air et rendra le démarrage duAiguisage de lame suite LameRéglage Réparation ou remplacement du ressort dentraînementReproduction Courroie en V D ou courroie dentraînement du moteur UséeReprod uction Entraîné Entretien de la courroie Remplacement du roulement à lextrémitéRemplacement de la courroie dentraîne De poulie de larbre hexagonalRemplacement de la courroie en V de Transmiss nDépannage ProblèmeGaranties Garantie LimitéeSeptembre Sur les pentes Guide de conduiteMoteur Spécifications 7800841-01 7800842-01Tondeuse

7800841-01, 780084-01, 7800842-01 specifications

The Snapper 7800842-01, 780084-01, and 7800841-01 are cutting-edge lawn care equipment designed to enhance the mowing experience while providing outstanding performance and reliability for homeowners and professionals alike. These models are part of Snapper's extensive lineup of outdoor power equipment, recognized for their durability and innovative features.

One of the main features of the Snapper 7800842-01 series is its advanced cutting technology. It is equipped with a robust 21-inch steel mowing deck, which ensures a clean and efficient cut, allowing users to tackle various lawn types and conditions. The durable construction of the deck not only enhances its longevity but also offers superior performance in mulching, bagging, or side-discharging grass clippings.

The Snapper series employs a powerful engine that delivers robust performance. With a reliable Briggs & Stratton engine, users can expect easy starting and impressive fuel efficiency. This engine is designed to provide ample torque for tackling tough grassy areas while ensuring smooth operation, reducing the effort required for maintaining your lawn.

Another notable feature is the adjustable cutting height system, which allows for easy customization of grass height. Users can quickly set their desired height for optimal mowing results, accommodating different grass types and seasonal growth patterns. This versatility is essential for achieving the perfect lawn manicuring experience.

Comfort is a priority in the design of the Snapper 7800842-01 series. The ergonomic handle design reduces operator fatigue, making it easier to maneuver the mower over more extensive areas. Additionally, the foldable handle feature simplifies storage and transportation, catering to users with limited space.

Safety features are also integrated into these models, ensuring peace of mind for users. An operator presence control system immediately stops the blade when the user releases the handle, preventing accidents.

Overall, the Snapper 7800842-01, 780084-01, and 7800841-01 models are a testimony to Snapper's commitment to quality and innovation. With their combination of reliable power, efficient cutting capabilities, and user-friendly design, they are well-suited for maintaining a pristine lawn. Whether used by homeowners seeking a perfect yard or professionals needing dependable equipment, these mowers stand out as excellent choices in the realm of outdoor power tools.