Snapper 5900683, 5900709, 5900734 Operation, General Operating Safety, Checks Before Starting

Page 15

Operation

General Operating Safety

Before first time operation:

•Be sure to read all information in the Safety and Operation sections before attempting to operate this tractor and mower.

•Become familiar with all of the controls and how to stop the unit.

•Drive in an open area without mowing to become accustomed to the unit.

WARNING

Never allow passengers to ride on the unit.

Before leaving the operator’s position for any reason, engage the parking brake, disengage the PTO, stop the engine and remove the key.

To reduce fire hazard, keep the engine, tractor and mower free of grass, leaves and excess grease. Do not stop or park tractor over dry leaves, grass or combustible materials.

Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is still hot from recent operation. Do not allow open flame, smoking or matches in the area. Avoid over-filling and wipe up any spills.

WARNING

Do not load this zero-turn rider on a trailer or truck using two separate ramps. Only use a single ramp that is at least one foot wider than the width of the rear wheels of this rider. This rider has a zero turning radius and the rear wheels could fall off the ramps, or the rider could tip over injuring the operator or bystanders.

Operation

WARNING

Never operate on slopes greater than (15°) which is a rise of 5.4 feet (1,6 m) vertically in 20 feet (607 cm) horizontally.

Select slow ground speed before driving onto a slope. Use extra caution when operating on slopes with a rear-mounted grass catcher.

Mow across the face of slopes, not up and down, use caution when changing directions and DO NOT START OR STOP ON SLOPE.

Checks Before Starting

•Check that crankcase is filled to full mark on the engine oil dipstick (A, Figure 3). See the engine Operator’s Manual for instructions and oil recommendations.

•Fill the fuel tanks with fresh fuel. Refer to engine manual for fuel recommendations.

•Make sure all nuts, bolts, screws and pins are in place and tight.

•Make sure the fuel selector valve (B) is in the “ON” position.

•Check the tire pressures. See Check Tire Pressures.

•Adjust the seat position, and make certain you can reach all controls from operator’s position. See Seat Adjustment

•Adjust the height of the mower deck to the desired position. See Mowing Height Adjustment.

B

A

Figure 3. Checks Before Starting

A.Engine Oil Dipstick

B.Fuel Valve Selector

Operation

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents North Main Street Briggs & Stratton Yard Power Products GroupDescription Model NumberDate Purchased Table of Contents Read the Manual Operator SafetyOperator Safety Operating SafetySlope Operation Thrown ObjectsMoving Parts Fuel and Maintenance Retaining WALLS, DROP-OFFS, and WaterEnclosed Areas Or warnings which must be followed TrainingPreparation OperationPeriods of exposure Towed Equipment RIDE-ON UnitsEmissions Ignition System Gasoline ModelsService and Maintenance Maintenance and StorageSafe Handling of Gasoline Safety Decals North American Safety Icons Safety Interlock SystemOperational Safety Checks Safety IconsFeatures and Controls Features and ControlsIdentification Numbers Ground Speed Control Levers Seat Adjustment LeverIgnition Switch Control FunctionsFeatures & Controls Checks Before Starting General Operating SafetyOperation OperationSeat Adjustment Check Tire PressuresTire Pressure Mowing Height Adjustment Foot Pedal AdjustmentTo adjust pedal position Pushing the Rider By Hand Insert the key into the ignition switch and turn it toStarting the Engine Stopping the RiderZero Turn Driving Practice Forward Travel PracticeForward Reverse Travel Executing Turns Practice Turning Around a CornerPractice Turning In Place Executing an End-Of-Row Zero TurnTall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassMowing Methods Engine Speed & Ground Speed for Mulching Attaching a TrailerProper Mulching Mulching Requires Excellent Mowing ConditionsSafety Items Before Every Spring Regular MaintenanceRegular Maintenance Maintenance ScheduleChange Oil & Filter Engine MaintenanceChecking / Adding Fuel Fuel FilterLubricating the Front Casters LubricationGrease OilChange Interval Every 200 Hours Replacement Filter Number Check / Fill Transmission OilTransmission Oil Filter Change Servicing The Mower Blades Inspecting the Mower BladesNever weld or straighten bent mower blades Balancing the Mower Blade Nail Reinstalling the Mower BladesGround Speed Control Lever Adjustment Speed Balancing AdjustmentNeutral Adjustment 375 0,95 cm Parking Brake AdjustmentReturn-to-Neutral Adjustment Jam Nuts Neutral Return Rod Return-to-Neutral AdjustmentMower deck Deck Rod Timing AdjustmentDeck Leveling Adjustment Adjustment is required continue with StepMower Belt Replacement 36 Deck Models To avoid damaging belts, do not PRY Belts Over PulleysAt this time Blade Alignment 36 Models Mower PTO Belt Idler Arm Stationary Idler Pulley Mower Belt Replacement 48 Deck ModelsUse extreme caution when removing this spring Hydraulic Pump Drive Belt ReplacementBattery Compartment Battery MaintenanceJump Starting With Auxiliary Booster Battery Battery ServiceChecking Battery Voltage Charging a Completely Discharged BatteryMake Certain Vehicles do not Touch Long Term Storage Longer Than 30 Days StorageStarting After Long Term Storage Temporary Storage 30 Days Or LessTroubleshooting the Rider TroubleshootingTroubleshooting Troubleshooting ChartTroubleshooting Streaking Troubleshooting Common Cutting ProblemsChassis SpecificationsDimensions EngineSurface Vertical a with Edge this Align LineIndentification SlopeFerris Limited Warranty Tractor Product SpecificationsCommon Service Parts HP Kawasaki
Top Page Image Contents