Snapper 5900683, 5900709, 5900734 manual Checking / Adding Fuel, Fuel Filter, Change Oil & Filter

Page 25

Checking / Adding Fuel

To add fuel:

1.Remove the fuel cap.

2.Fill the tank to about 1-1/2” (3,81 cm) of the bottom of the filler neck. This will allow for fuel expansion.

NOTE: Do not overfill. Refer to your engine manual for specific fuel recommendations.

3. Install and hand tighten the fuel cap.

Fuel Filter

The fuel filter is located in the fuel line between the fuel tank and the carburetor, near the fuel pump. If filter is dirty or clogged, replace as follows:

1.Disconnect the negative battery cable.

2.Place a container below the filter to catch any spilled fuel.

3.Using pliers, open and slide the hose clamps from the fuel filter (D, Figure 19).

4.Remove the hoses from the fuel filter.

5.Install the new fuel filter in the proper flow direction in the fuel line.

6.Secure with the hose clamps.

7.Reconnect the negative battery cable when finished.

Change Oil & Filter

1.Warm engine by running for a few minutes. (Refer to the engine operator’s manual for oil and filter replacement instructions.)

2.Briggs & Stratton Models: Locate the oil drain hose (A, Figure 19) on the left side of the engine and route the oil drain hose over the rear of the engine deck.

Kawasaki Models: Locate the oil drain hose (A, Figure 19) on the right side of the engine and route the oil drain hose over the rear of the engine deck.

3.Place a small pan under the oil drain hose to catch the oil. Using the appropriate tools, remove the cap (B) from the oil drain hose (A) and drain the engine oil into the pan.

4.After draining, replace the cap and wipe up any spilled oil. Route the oil drain towards the front of the machine facing so the oil drain hose is retained during normal operation.

5.Place an absorbent shop cloth under the engine oil filter. Remove the engine oil filter and replace with a new one.

6.Briggs & Stratton Models: Remove the engine oil dipstick (F) that is located on the left side of the engine and refill with new oil (Refer to the engine operator’s manual for oil recommendations.)

Kawasaki Models: Remove the engine oil dipstick (F) that is located on the right side of the engine and refill with new oil (Refer to the engine operator’s manual for oil recommendations.)

7.Remove the shop cloth and wipe up any spilled oil.

Engine Maintenance

Refer to the engine owner’s manual for all engine maintenance procedures and recommendations.

Regular Maintenance

WARNING

Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is still hot from recent operation. Do not allow open flame, smoking or matches in the area. Avoid over-filling and wipe up any spills.

Do not remove fuel filter when engine is hot, as spilled gasoline may ignite. DO NOT spread hose clamps further than necessary. Ensure clamps grip hoses firmly over filter after installation.

NOTICE

Do not use gasoline containing METHANOL, gasohol containing more than 10% ethanol, gasoline additives, premium gasoline, or white gas because engine/fuel system damage could result.

 

E

 

 

F

 

D

B

A

 

 

 

 

C

 

Figure 19. Engine Oil Drain (Briggs & Stratton shown)

A.Oil Drain Hose

B.Cap

C.Oil Filter

D.Fuel Filter

E.Fuel Tank Selection Valve

F.Oil Dipstick

Maintenance

23

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Description Briggs & Stratton Yard Power Products GroupModel Number North Main StreetDate Purchased Table of Contents Operator Safety Operator SafetyOperating Safety Read the ManualThrown Objects Slope OperationMoving Parts Retaining WALLS, DROP-OFFS, and Water Fuel and MaintenanceEnclosed Areas Preparation TrainingOperation Or warnings which must be followedEmissions Towed Equipment RIDE-ON UnitsIgnition System Gasoline Models Periods of exposureMaintenance and Storage Service and MaintenanceSafe Handling of Gasoline Safety Decals Operational Safety Checks Safety Interlock SystemSafety Icons North American Safety IconsFeatures and Controls Features and ControlsIdentification Numbers Ignition Switch Seat Adjustment LeverControl Functions Ground Speed Control LeversFeatures & Controls Operation General Operating SafetyOperation Checks Before StartingCheck Tire Pressures Seat AdjustmentTire Pressure Foot Pedal Adjustment Mowing Height AdjustmentTo adjust pedal position Starting the Engine Insert the key into the ignition switch and turn it toStopping the Rider Pushing the Rider By HandForward Travel Practice Zero Turn Driving PracticeForward Reverse Travel Practice Turning In Place Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn Executing TurnsMowing Recommendations MowingHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods Proper Mulching Attaching a TrailerMulching Requires Excellent Mowing Conditions Engine Speed & Ground Speed for MulchingRegular Maintenance Regular MaintenanceMaintenance Schedule Safety Items Before Every SpringChecking / Adding Fuel Engine MaintenanceFuel Filter Change Oil & FilterGrease LubricationOil Lubricating the Front CastersCheck / Fill Transmission Oil Change Interval Every 200 Hours Replacement Filter NumberTransmission Oil Filter Change Inspecting the Mower Blades Servicing The Mower BladesNever weld or straighten bent mower blades Balancing the Mower Blade Nail Reinstalling the Mower BladesSpeed Balancing Adjustment Ground Speed Control Lever AdjustmentNeutral Adjustment 375 0,95 cm Parking Brake AdjustmentReturn-to-Neutral Adjustment Jam Nuts Neutral Return Rod Return-to-Neutral AdjustmentDeck Leveling Adjustment Deck Rod Timing AdjustmentAdjustment is required continue with Step Mower deckTo avoid damaging belts, do not PRY Belts Over Pulleys Mower Belt Replacement 36 Deck ModelsAt this time Blade Alignment 36 Models Mower PTO Belt Idler Arm Stationary Idler Pulley Mower Belt Replacement 48 Deck ModelsUse extreme caution when removing this spring Hydraulic Pump Drive Belt ReplacementBattery Compartment Battery MaintenanceChecking Battery Voltage Battery ServiceCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryMake Certain Vehicles do not Touch Starting After Long Term Storage StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysTroubleshooting TroubleshootingTroubleshooting Chart Troubleshooting the RiderTroubleshooting Streaking Troubleshooting Common Cutting ProblemsDimensions SpecificationsEngine ChassisIndentification LineSlope Surface Vertical a with Edge this AlignFerris Limited Warranty Common Service Parts Product SpecificationsHP Kawasaki Tractor
Top Page Image Contents