Snapper 3317523BVE specifications Engine Manual Start, Setting the park brake

Page 10

Operation (Continued)

Starting and Operation (Continued)

Engine (Electric Start) (Continued)

A

8.Should the battery be too weak to start the engine, refer to the Section entitled “Engine (Manual Start)” to manually start the electric start engines.

9.On Model 3314522BVE, the engine is equipped with a fuel shut-off solenoid. If the battery is dead, the engine can be started with the recoil back-up starter if the engine speed control is in the choke position (HOT engine or COLD engine).

Engine (Manual Start)

B

Operation

IMPORTANT: When the key is turned to “ON”, and the recoil handle is pulled, the engine will turn over, but will not start unless the Clutch/Brake Pedal is pressed all the way down with the Park Brake engaged, and the Blade Lever is in the “Off” position.

Start the engine as follows:

1.Open the vent (B, Figure 2) on the fuel filler cap (A) by turning counterclockwise.

IMPORTANT: Failure to open the vent on the fuel filler cap can cause the engine to stall.

2.Move the transmission shift lever to the (N) Neutral position. Refer to the section entitled “Wheel Drive”.

IMPORTANT: DO NOT start the engine with the transmission shift lever in a drive position.

Figure 8: Setting the park brake

5.Move the engine speed control (A, Figure 6) to the choke position (B) to start a cold engine.

6.Turn the key (A, Figure 9) to the “ON” position.

A

!

WARNING

!

It is possible to start the engine with the transmission shift lever in a drive position. Follow starting instructions carefully.

3.Make certain the Blade Lever (A, Figure 4) is in the “OFF” position.

4.Press the Clutch/Brake Pedal (A, Figure 8) all the way down, move the park brake latch (B) over, and release the clutch/brake pedal to set the park brake.

Figure 9: Key

7.Pull the starter rope, located on the engine recoil, with a smooth, even motion until the engine starts.

NOTE: Always guide the starter rope back into the recoil housing. Never allow rope to snap back.

After the engine starts, move the engine speed control to the “FAST” position.

8. Allow a brief warm-up until the engine runs smooth.

8

www.snapper.com

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Series Snapper is a trademark Date of Purchase Retailer Retailers Phone Number EquipmentEngine Simplicity Manufacturing, IncTable of Contents Preparation Protection for ChildrenProtection against Tipovers Do not allow pre-teenage children to operate machineSafe Handling of Gasoline OperationMaintenance TowingFeatures and Controls Features and ControlsFuel Tank Operation Pre-Start Check List OPERATOR’S Seat AdjustmentFuel filler cap A, is tight, and the vent B is Engine runs smooth Operation Starting and OperationEngine Electric Start On Next OperationSetting the park brake Engine Manual StartMower Blade OperationWheel Drive Stopping Engine Wheel Drive, Blade Stop the engine by turning the key A, to the OFF positionBlade Cutting Height AdjustmentOperation Stopping Engine, Wheel Drive Park BrakeAte blades in reverse. Stop BLADES, Look and see Operation Reverse Lockout MechanismReverse Lockout Mechanism Override While backingService After the First 5 Hours MaintenanceIntroduction Check the Blade Drive Belt Service Brake / Park BrakeBlade Drive Belt Replacement Blade BrakeReverse Lockout Mechanism Safety Interlock System ChecksCheck Engine Lubrication Grease FittingsService Every 25 Operating Hours Rear Axle Bearing Lubrication Engine ServiceDifferential / Chain Case Lubrication Storage Out of Season Service AnnuallyEvery Two Years Removing the Fuel TankBlade Brake Adjustment Engine Adjustments and RepairMower Deck and Component Adjustments Reinstall the belt cover and tighten the bolts securelyMower Deck Adjustment Side-To-Side Levelness Mower Deck Adjustment Front-to-Rear LevelnessMove the blade lever up and over to the on position Mower Drive Belt Adjustment For 28 & 30 Decks OnlyService BRAKE/PARK Brake Adjustment To the rear main caseRear Engine Rider Drive Components Measurement should be 3/4Blade Wear Limits Mower Blade ReplacementSigns of excessive wear or damage Blade Sharpening Tled Mower Drive Belt Adjustment Belt ReplacementDo not attempt any adjustments, maintenance, service or Belt RemovalBattery Installation BatteryBattery Removal Slide the battery partially into the battery housingNew Battery Preparation Battery ServiceBattery Storage Battery TestingBattery Condition Chart Snapper Rear Engine Rider AccessoriesDescription of Kit Models Used on Maintenance Service Schedule SeasonMaintenance Maintenance/Replacement Parts Problem Probable Cause Corrective Action TroubleshootingStop Move lever to the on position Year Limited Warranty Slope Guide Page Page Page Page Common Service Parts Product Specifications 2811523BVSnapper Products Macon Street McDonough, GA

3317523BVE specifications

The Snapper 3317523BVE is a cutting-edge lawn mower designed to cater to homeowners who prioritize performance, efficiency, and ease of use in their gardening tools. This model stands out in the Snapper line for its robust engineering and innovative features, making it an excellent choice for residential lawn care.

One of the key features of the Snapper 3317523BVE is its powerful engine. Equipped with a reliable Briggs & Stratton engine, this mower delivers the necessary power for effective grass cutting, accommodating various grass types and conditions. The engine is not only powerful but also designed for fuel efficiency, allowing users to complete their mowing tasks without frequent refueling interruptions.

The Snapper 3317523BVE boasts a 21-inch cutting deck, which enhances maneuverability even in tight spaces. This compact size makes it suitable for urban and suburban lawns, where obstacles like flower beds and trees are common. Additionally, the cutting height is adjustable, with several settings available to allow for flexibility based on the grass type and weather conditions.

Another notable characteristic of the Snapper 3317523BVE is its innovative rear-wheel drive system. This feature significantly improves traction on slopes and uneven terrains, enabling users to maintain control over the mower, particularly in challenging mowing conditions. The wheels are designed for durability and stability, ensuring that they can handle the rigors of regular use.

The ergonomic handle design on the Snapper 3317523BVE adds to the overall user experience, allowing for comfortable operation. The handle can be adjusted for height, accommodating users of various sizes and preferences, while also providing a folding mechanism for easy storage.

Snapper's patented SmartChoke technology simplifies the starting process, reducing the hassle often associated with traditional mowers. This technology ensures a reliable start every time, even in varying weather conditions.

Moreover, the Snapper 3317523BVE's robust build is complemented by a sturdy plastic housing that is resistant to rust and corrosion, ensuring longevity and maintaining the mower's appearance over time.

Overall, the Snapper 3317523BVE is engineered to provide a seamless and efficient mowing experience, combining power, durability, and user-friendly features. This mower is a testament to Snapper's commitment to quality in the lawn care industry, making it a reliable choice for homeowners looking to maintain their gardens with ease.
Top Page Image Contents