Snapper 3317523BVE Battery Service, Battery Storage, New Battery Preparation, Battery Testing

Page 28

Maintenance (Continued)

Maintenance

!

WARNING

!

The electrolyte (acid) produces a highly explosive gas. Keep all sparks, flame and fire away from area when charging battery or when handling electrolyte or battery. Electrolyte (acid) is a highly corrosive liquid. Wear eye protection. Wash affected areas immediately after having eye or skin contact with electrolyte (acid). Battery acid is corrosive. Rinse empty acid containers with water and mutilate before discarding. If acid is spilled on battery, bench, or clothing, etc., Flush with clear water and neutralize with baking soda. DO NOT attempt to charge battery while installed on the rider. DO NOT use “BOOST” chargers on the battery.

Battery Service

1.Remove the battery. Refer to the section entitled “BAT-

TERY REMOVAL”.

2.Place the battery in a well ventilated area on a level sur- face.

3.Using distilled water, refill the cells as required to cover the cell plates (of which can also be viewed through the plastic battery case).

4.With the cell caps removed, connect the battery charger to the battery terminals. Red to positive (+) terminal and black to negative (-) terminal.

5.Slow charge the battery at 1 amp for 10 hours.

6.If the battery will not accept a charge or is partially charged after 10 hours of charging at 1 amp, replace with a new battery.

Battery Storage

If the mower is to be stored out of season on its rear bumper, it is recommended the battery be removed, charged and stored.

1.Remove the battery. Refer to the section entitled “BAT-

TERY REMOVAL”.

2.Perform battery service.

3.Bring the battery to full charge, if required.

4.Store the battery in an area away from the rider on a wood surface. DO NOT STORE THE BATTERY ON A CONCRETE SURFACE.

New Battery Preparation

1.Remove the battery from the carton.

2.Place the battery in a well ventilated area on a level non- concrete surface.

3.Remove the battery cell caps. Fill the cells as required with electrolyte (purchased separately) to the proper level. Filling the battery with electrolyte will bring the battery to 80% charged state.

4.With the cell caps removed, connect the battery charger to the battery terminals; RED to positive (+) and BLACK to negative (-) terminal.

!

WARNING

!

DO NOT attempt to charge the battery while installed on the rider. DO NOT use “BOOST” chargers on the battery.

DO NOT OVERFILL!

IMPORTANT: Never place anything in the battery other than the specified electrolyte.

5.Slow charge the battery at 1 amp for 2 hours to bring the battery to full charge.

6.After charging, check the level of electrolyte and add as needed to bring the level to 3/16” above the cell plates.

7.Reinstall the cell caps.

8.Remove the hair pin and swivel from the deck support to allow clearance for battery installation.

9.Slide the battery partially into the battery housing.

10.Connect the red positive (+) cable (B, Figure 49) first, from the wiring harness to the positive terminal (+) on the battery, using the bolt and nut provided in the hard- ware bag. Connect the black negative (-) cable (A) last, to the negative terminal (-) on the battery, using the bolt and nut. Apply a small amount of grease over the termi- nals to prevent corrosion.

11.Insert the battery completely into the battery housing.

12.Reinstall the battery cover (A, Figure 48).

13.Reinstall the swivel and hair pin for the deck support.

Battery Testing

There are two types of battery tests: Unloaded and Loaded. The unloaded test is the procedure that will be discussed. It’s the simplest and most commonly used. An unloaded test is made on a battery without discharging current. To perform unloaded testing, check charge condition using either a hydrometer or voltmeter.

1.Using a voltmeter, voltage readings appear instantly to show the state of charge. Remember to hook the posi- tive lead to the battery’s positive terminal, and the nega- tive lead to the negative terminal.

2.A hydrometer measures the specific gravity of each cell. The specific gravity tells the degree of charge; generally, a specific gravity of about 1.265 to 1.280 indicates full charge. A reading of 1.230 to 1.260 indicates the battery should be charged. The chart on the next page shows the charge level as measured by syringe float hydrome- ter, digital voltmeter and five ball hydrometer.

!

WARNING

!

Shield the positive terminal with the terminal cover located on the battery harness. This prevents metal from touching the positive terminal, which could cause sparks.

26

www.snapper.com

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Series Date of Purchase Retailer Retailers Phone Number Equipment EngineSnapper is a trademark Simplicity Manufacturing, IncTable of Contents Protection for Children Protection against TipoversPreparation Do not allow pre-teenage children to operate machineSafe Handling of Gasoline OperationMaintenance TowingFeatures and Controls Features and ControlsFuel Tank Operation Pre-Start Check List OPERATOR’S Seat AdjustmentFuel filler cap A, is tight, and the vent B is Operation Starting and Operation Engine Electric StartEngine runs smooth On Next OperationSetting the park brake Engine Manual StartMower Blade OperationWheel Drive Stopping Engine Wheel Drive, Blade Stop the engine by turning the key A, to the OFF positionCutting Height Adjustment Operation Stopping Engine, Wheel DriveBlade Park BrakeOperation Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideAte blades in reverse. Stop BLADES, Look and see While backingService After the First 5 Hours MaintenanceIntroduction Service Brake / Park Brake Blade Drive Belt ReplacementCheck the Blade Drive Belt Blade BrakeSafety Interlock System Checks Check EngineReverse Lockout Mechanism Lubrication Grease FittingsService Every 25 Operating Hours Rear Axle Bearing Lubrication Engine ServiceDifferential / Chain Case Lubrication Service Annually Every Two YearsStorage Out of Season Removing the Fuel TankEngine Adjustments and Repair Mower Deck and Component AdjustmentsBlade Brake Adjustment Reinstall the belt cover and tighten the bolts securelyMower Deck Adjustment Side-To-Side Levelness Mower Deck Adjustment Front-to-Rear LevelnessMower Drive Belt Adjustment For 28 & 30 Decks Only Service BRAKE/PARK Brake AdjustmentMove the blade lever up and over to the on position To the rear main caseRear Engine Rider Drive Components Measurement should be 3/4Blade Wear Limits Mower Blade ReplacementSigns of excessive wear or damage Blade Sharpening Belt Replacement Do not attempt any adjustments, maintenance, service orTled Mower Drive Belt Adjustment Belt RemovalBattery Battery RemovalBattery Installation Slide the battery partially into the battery housingBattery Service Battery StorageNew Battery Preparation Battery TestingBattery Condition Chart Snapper Rear Engine Rider AccessoriesDescription of Kit Models Used on Maintenance Service Schedule SeasonMaintenance Maintenance/Replacement Parts Problem Probable Cause Corrective Action TroubleshootingStop Move lever to the on position Year Limited Warranty Slope Guide Page Page Page Page Common Service Parts Product Specifications 2811523BVSnapper Products Macon Street McDonough, GA

3317523BVE specifications

The Snapper 3317523BVE is a cutting-edge lawn mower designed to cater to homeowners who prioritize performance, efficiency, and ease of use in their gardening tools. This model stands out in the Snapper line for its robust engineering and innovative features, making it an excellent choice for residential lawn care.

One of the key features of the Snapper 3317523BVE is its powerful engine. Equipped with a reliable Briggs & Stratton engine, this mower delivers the necessary power for effective grass cutting, accommodating various grass types and conditions. The engine is not only powerful but also designed for fuel efficiency, allowing users to complete their mowing tasks without frequent refueling interruptions.

The Snapper 3317523BVE boasts a 21-inch cutting deck, which enhances maneuverability even in tight spaces. This compact size makes it suitable for urban and suburban lawns, where obstacles like flower beds and trees are common. Additionally, the cutting height is adjustable, with several settings available to allow for flexibility based on the grass type and weather conditions.

Another notable characteristic of the Snapper 3317523BVE is its innovative rear-wheel drive system. This feature significantly improves traction on slopes and uneven terrains, enabling users to maintain control over the mower, particularly in challenging mowing conditions. The wheels are designed for durability and stability, ensuring that they can handle the rigors of regular use.

The ergonomic handle design on the Snapper 3317523BVE adds to the overall user experience, allowing for comfortable operation. The handle can be adjusted for height, accommodating users of various sizes and preferences, while also providing a folding mechanism for easy storage.

Snapper's patented SmartChoke technology simplifies the starting process, reducing the hassle often associated with traditional mowers. This technology ensures a reliable start every time, even in varying weather conditions.

Moreover, the Snapper 3317523BVE's robust build is complemented by a sturdy plastic housing that is resistant to rust and corrosion, ensuring longevity and maintaining the mower's appearance over time.

Overall, the Snapper 3317523BVE is engineered to provide a seamless and efficient mowing experience, combining power, durability, and user-friendly features. This mower is a testament to Snapper's commitment to quality in the lawn care industry, making it a reliable choice for homeowners looking to maintain their gardens with ease.
Top Page Image Contents