Snapper 2690629, 2690628 manual Leveling The Mower, Spacer

Page 42

Leveling The Mower

If the cut is uneven, the mower may need leveling.

NOTE: Unequal or improper tire pressure may also cause an uneven cut.

SIDE TO SIDE LEVELING

1.With the mower installed, place the tractor on a smooth, level surface such as a concrete floor. Turn the front wheels straight forward.

2.Place the cutting height adjust in high-cut position.

3.Set the parking brake, turn off the ignition, and remove the key.

4.Check for bent blades and replace if necessary.

5.Arrange the mower blades so that they are pointing from side-to-side.

6.Measure the distance between the outside tips of each blade and the ground. If there is more than 1/8" (3mm) difference between the measurements on each side, proceed to step 7. If the difference is 1/8" (3mm) or less, proceed to Front To Back Leveling.

7.See Figure 46. Prevent I-Bolt (C) from turning; then adjust spacer (B) by turning lock nut (A) clockwise (up) or counter-clockwise (down) to achieve correct side to side leveling.

FRONT TO BACK LEVELING

1.Arrange the blades so they face front-to-back.

2.Measure the distance from the ground to the front of the front blade and from the rear tips of the rear blades. Front tips should be 1/8" to 1/4" higher than the rear tips. If not, proceed to step 3.

3.See Figure 47. Loosen the Iocknut (A) on the arm assembly. Adjust the jam nut on the arm until the mower deck is level or the front is 1/8" to 1/4" higher.

TpoubJeshootin9oAdjustment,& Service

AWARNING

Before checking mower, shut off PTO and engine. Allow all moving parts to stop. Remove ignition key, then disconnect the spark plug wires and fasten them away from the spark plugs.

Figure 46. Side=to=Side Adjustment

A. Lock Nut, 5/16-18

B.Spacer

C.I=Boit

Figure 47. Front to Back Leveling

A. Jam Nuts

41

Page 41 Page 43
Image 42
Page 41 Page 43
Contents GT600 Series 27HP Hydro Tractors & Mower Decks 54 Mower DecksAbleof Contents OporatingSafety Meving SafetyRuJes& lflfomatJofl SafetyRulesandinformation Service and Maintenance Service & MaintenanceJdefltificatioflNumbers Tracto Mower ID TagPositions Safety DecalsDecal =Throttle Decal Transmission Decal =Attachment Lift Control Decal CuttingOperational Safety Checks Safetylcofls/ SafetyinteplockTestSafety icons Purpose of the safety interlock systemControl Functions Choke Select lVlodelsFront A×Je Oil LeveJ Plug Features& Cofltrols Features& Cefltrols Parking Brake FunctionAutomatic Controlled Traction Dashboard Display Functions Irregular VoltageFuel Gauge Adding Fuel General Operating SafetySlope Operation Starting The EngineAttachment Operation in Reverse OperatiflgtheTractorMowing in Reverse Wheel Drive OperationHydraulic System Functions Using Inboard HydraulicsPushing The Tractor By Hand GeneralUsing Auxiliary Hydraulics Auxiliary Hydraulics Angle Left Angle RightOperatJflgtheTractor Max. Attachment WeightAttachment Weight Limit Locking The HitchHitch Arms Installation Starting & Stopping the PTO Connecting a Drive ShaftChecks Before Starting Engine Speed SelectionPTO BOX Output Speed & Horsepower Output Attachment RecommendationsMower Deck Removal & installation Removing the Mower DeckInstalling the Mower Deck Mower Electrical ConnectionVolt Power Outlet Attaching a TrailerStorage Hours Safety iTEMSEvery UseCheck Engine Coolant Level Clean RadiatorClean Transmission Oil Cooler Change Engine CoolantRegularMaintenance Drain Fuel SeparatorCheck Transmission Oil Level Transmission Fluid Check Dip StickChange Transmission Oil & filter Check Front Axle Oil Level17ram Drain Plug Safety Interlock System Check Check Mower Deck Gear Box OilBlade Brake Check Check Tire Pressures Battery MaintenanceCleaning the Battery and CabJes Size Tread PSiLubrication Every 25 HoursGrease Deck Lubrication Every 10 Hours Servicing The Mower Blades InjurySpring Washer Capscrew RegularlVlaifltenance Troubleshooting, Adjustment,& Service Engine will not turnover or startTroubJeshootin9oAdjustment,& Service Tractor Troubleshooting ContMower will not raise TrouhJeshooti&q,Adjustment,& Service Seat AdjustmentSeat Slide Adjustment Teouhleshootin9oAdjustment,& Service Headlight ReplacementTaillight & Dash Light Replacement Gauge Wheel Adjustment TroubJeshooti&j,Adjustment,& ServiceMower Adjustments Hair Pin Upper PositionLeveling The Mower SpacerMower Drive Belt Replacement TpouhJeshootin9oAdjustment,& ServiceMower Belt Replacement Drive Idler CenterDiMENSiONS 4WD27 HP Briggs Stratton Accessories Replacement Parts TechnicalMaintenance Items Manuals

2690629, 2690628 specifications

Snapper 2690628 and 2690629 are innovative lawn care solutions that have gained significant attention in the outdoor equipment market. These models are designed for homeowners who seek efficiency and reliability in their lawn maintenance routine. Featuring powerful engines and cutting-edge technology, they stand out as top contenders for those who prioritize performance and ease of use.

One of the main features of the Snapper 2690628 and 2690629 is their robust engine performance. Both models are equipped with reliable Briggs & Stratton engines that provide ample power for tackling dense grass and tough terrain. This ensures that users can complete their mowing tasks quickly and efficiently, with minimal effort required.

These mowers are designed with ease of use in mind. The intuitive controls and ergonomic design allow for comfortable handling during extended mowing sessions. The push-button start feature eliminates the hassle of pulling cords, making it easier for users to get started. Furthermore, the adjustable cutting height feature gives users the versatility to achieve their desired grass length, whether they prefer a golfing green finish or a more natural look.

Another noteworthy technology is the mulching capability featured in both models. The Snapper 2690628 and 2690629 can effortlessly convert grass clippings into fine mulch. This not only reduces yard waste but also returns valuable nutrients to the soil, promoting a healthier lawn. Additionally, the side discharge option allows for efficient grass disposal, making it suitable for various mowing preferences.

Durability is another significant characteristic of the Snapper 2690628 and 2690629. Both models feature a sturdy steel deck that withstands the rigors of outdoor use, ensuring longevity. The rust-resistant finish further enhances their lifespan, allowing users to enjoy the benefits of their mowers for years to come.

In conclusion, the Snapper 2690628 and 2690629 represent a remarkable combination of power, technology, and user-friendly features. With their reliable engines, ergonomic designs, and practical mowing capabilities, they are ideal choices for homeowners looking to maintain a pristine lawn effortlessly. These models not only prioritize performance but also emphasize comfort and durability, making them valuable additions to any lawn care arsenal.
Top Page Image Contents