Snapper 7800932-00, 7800920-00 Battery Service Sealed Lead Acid Type, How To Install The Battery

Page 27
NOTICE: Use only a manufacturer-approved charger when charging the battery. Contact your authorized dealer.
AVOID SERIOUS INJURY AND PROPERTY DAMAGE. DO NOT attempt to charge the battery while installed on the unit. DO NOT attempt to charge this battery with automotive or ‘Boost’ chargers. DO NOT attempt to jump start a unit that has a dead battery. Always use the charger supplied with the unit to charge this battery.
1. Remove the battery. Refer to “How To Remove The Battery”.
2. Using a manufacturer-approved battery charger (not supplied), plug the connector on the battery charger (not shown) into the battery harness connector (A, Figure 32).

Maintenance

!

WARNING

!

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. DO NOT attempt to service or charge the battery while it is installed on the machine.

Battery Service -

Sealed Lead Acid Type

The battery provided with your unit is sealed and mainte- nance-free. It requires no special care other than keeping it properly charged.

How To Remove The Battery

How To Charge The Battery

Charge the battery after each use, and if the battery has been stored for longer than 30 days.

!

WARNING

!

 

 

 

1. Raise the operator seat to gain access to the battery

 

 

 

compartment.

 

 

 

3.

Plug the charger into a 120-volt wall outlet.

2. Disconnect the battery harness (A, Figure 32) from the

 

main harness (B).

 

 

 

4.

Charge the battery for a period of 16 to 24 hours.

NOTE: Grasp the connectors; do not pull

the wires.

5.

(Longer periods will not damage the battery.)

Unplug the charger from the wall outlet.

3. Unhook one end of the battery strap (C) from the wire-

6.

Unplug the charger from the battery harness connector.

 

form (D).

 

 

 

How To Install The Battery

4. Carefully remove the battery (E).

 

 

 

 

 

 

 

1.

Raise the operator seat.

 

A

 

 

 

 

 

 

 

2.

Install the battery (E, Figure 32) into the battery compart-

 

B

 

 

E

3.

ment, orientating it in the wireform (D) as shown.

 

 

 

Secure the battery with the battery strap (C), hooking the

 

 

Not

for

 

loose end onto the wireform. Be sure to pass the strap

 

 

4.

under the battery harness wires.

 

 

 

Connect the main harness (B) to the battery harness

 

 

 

 

(A).

 

 

 

How To Store The Battery

 

 

C

If the unit is to be stored out of season, it is recommended

 

 

the battery be removed, charged and stored.

 

 

 

 

 

1.

Remove the battery. Refer to “How To Remove The

 

D

 

 

 

2.

Battery”.

 

 

 

 

Charge the battery. Refer to “How To Charge The

 

 

 

Reproduction

 

 

 

 

 

 

Battery”.

 

 

 

 

 

3.

Store the battery in an area away from the unit on a

 

Figure 32: Battery (sealed lead acid type)

 

 

 

 

wood surface. DO NOT STORE THE BATTERY ON A

CONCRETE SURFACE.

en

27

Image 27
Contents Not For ReproductionNot Table of Contents ChildrenC il renReproductioReversen Operator Safety Operating SafetyNot Orf Read the ManualOperator Safety Slope Operation Fuel and MaintenanceReproduction Thrown ObjectsMoving Parts Operator Safety Protection Against Tip-Overs/Roll-OversProtection for Children Preparation OperationSafe Handling of Gasoline Towing MaintenanceFor Reproduction For Safety and Instructional DecalsExplanation of Instructional Decals Explanation of Safety DecalsFor Not Features and Controls Features and ControlsBefore adding or checking the oil How To Check/Add OilOperation Before StartingHow To Adjust The Operator Seat How To Add FuelFuel Recommendations How To Start The Engine Forward How To Engage The Mower BladeEngine Mower BladeTransmission Deflector How To Set The Parking Brake Reverse Mowing Option RMOHow To Push The Unit By Hand Repr OductionTowing Implements Maintenance Maintanance ChartEmissions Control Equipped How To Change The Oil Filter ifOval Air Filter How To Service The Air FilterNotB Flat Air FilterRider Maintenance Basic How To Check The Mower Drive Belts Rider Maintenance AdvancedHow To Service The Fuel Filter How To Check The Mower BladeHow To Lubricate Mower Deck Linkage How To Lubricate Grease FittingsHow To Lubricate Differential / Chain How To Lubricate Mower Blade SpindleHow To Store The Battery Battery Service Sealed Lead Acid TypeHow To Remove The Battery How To Charge The Battery How To Install The BatteryBattery valve regulated type Battery Service Valve Regulated TypeStorage Fuel SystemBriggs & Stratton Fresh Start available in a drip con How To Inspect The Mower Blade Engine Adjustments and RepairsRider Adjustments And Repairs How To Sharpen The Mower BladeSide-To-Side Leveling How To Level The Mower DeckReproduction B RepairHydro Drive Models How To Adjust The Brake / Parking BrakeHow To Adjust Mower Blade Belt Tension Manual Drive ModelsHow To Adjust The Blade Brake How To Remove The Deck Cover Problem Probable Cause Corrective Action TroubleshootingTroubleshooting Warranties Limited WarrantyBriggs & Stratton Emissions Control Warranty Provisions Page Page 4.5 / 1,6 7,2 0 / 0 8,0

7800918-00, 7800920-00, 7800932-00 specifications

The Snapper 7800920-00, 7800918-00, and 7800932-00 represent a series of high-performance mowers designed for both residential and commercial use. These models leverage advanced technologies and engineering, making them some of the most reliable and efficient choices on the market for lawn care enthusiasts and professionals alike.

One of the standout features of the Snapper 7800 series is their powerful engine options. Most models in this range are equipped with reliable Briggs & Stratton engines, known for their durability and easy starting capabilities. This ensures that users can tackle tough mowing jobs with confidence, whether dealing with thick grass, uneven terrain, or large lawns.

The cutting deck of these mowers is another significant highlight. The Snapper 7800920-00 features a 21-inch steel cutting deck that provides a clean and even cut, improving the overall appearance of your lawn. The other models, 7800918-00 and 7800932-00, offer a similar design with slight variations suited for different mowing needs. The adjustable cutting height allows users to customize the lawn cut based on personal preferences or seasonal requirements.

In terms of usability, these mowers come with ergonomic handles designed for comfort during prolonged use. The handles are often adjustable, catering to different user heights and improving maneuverability across various lawn types. The self-propelled feature, present in many models, allows easy navigation across slopes or uneven ground, making these mowers suitable for a variety of landscapes.

Snapper also integrates innovative technologies that enhance operational efficiency. Features such as efficient bagging systems allow for easy grass collection while reducing the need for raking afterward. The mulching capability, prevalent in these models, provides an eco-friendly solution by returning grass clippings to the lawn, promoting healthier growth.

Safety is another priority with Snapper's design ethos. These mowers are equipped with safety features such as blade brake systems and easily accessible controls that ensure users can operate the machines safely and effectively.

In conclusion, the Snapper 7800920-00, 7800918-00, and 7800932-00 incorporate advanced engineering, powerful performance, and user-friendly features that cater to the needs of both casual lawn caretakers and professional landscapers. With their strong build quality, reliability, and array of capabilities, these models stand out as excellent investments for maintaining pristine outdoor spaces.