Snapper 7800920-00, 7800932-00, 7800918-00 manual How To Change The Oil Filter if, Equipped

Page 22

Maintenance

 

 

 

How To Change The Oil Filter (if

!

WARNING

!

equipped)

DO NOT attempt any adjustments, maintenance, service or

Some models are equipped with oil filter. For replacement

repairs with the engine running. STOP engine. STOP blade.

intervals, see the Maintenance chart.

Engage parking brake. Remove key. Remove spark plug

1.

Drain the oil from the engine. Refer to “How To Change

wire from spark plug and secure away from plug. Engine

2.

The Engine Oil”.

and components are HOT. Avoid serious burns, allow all

Remove the oil filter (A, Figure 23) and dispose of

parts to cool before working on machine.

 

 

properly.

Engine Maintenance

 

NOTE: Location of oil filter may vary according to model.

 

3. Before you install the new oil filter, lightly lubricate the oil

How To Change The Engine Oil

 

filter gasket with fresh, clean oil.

 

 

4. Install the oil filter by hand until the gasket contacts the

Used oil is a hazardous waste product and must be disposed

oil filter adapter, then tighten the oil filter 1/2 to 3/4 turns.

of properly. Do not discard with household waste. Check with

5. Add oil. Refer to “How to Check/Add Oil” in the

your local authorities, service center, or dealer for safe dis-

Operation section.

 

posal/recycling facilities.

 

 

 

 

 

6. Start and run the engine. As the engine warms up, check

1. Place bricks or wooden blocks under the front wheels to

for oil leaks.

 

lower the rear of the engine.

 

 

 

7. Stop the engine and check the oil level. It should be at

2. Loosen or remove the oil fill cap on the engine.

the top of the full indicator on the dipstick.

 

3. Place a 2 quart minimum capacity container under the

 

end of the oil drain (Figure 22).

 

 

 

4. Remove or open the oil drain plug (A or B, Figure 22),

 

 

depending upon the type of oil drain plug the engine is

 

 

equipped with.

 

 

 

 

NOTE: Location of oil drain may vary according to model.

 

 

 

A

for

 

 

 

 

 

A

 

 

 

 

 

B

 

Figure 23: Oil filter

 

 

 

 

 

Figure 22: Oil drain plugs

Not

 

 

 

 

 

 

 

5. After all the oil has drained, replace or close the drain

 

 

plug, and wipe up any oil that may haveReprospilled. Disposeduction

 

of used oil properly.

 

 

 

 

6. Fill the engine with new oil. Refer to “How To Check/

 

 

Add Oil” in the Operation Section.

 

 

 

22

www.snapper.com

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Reproduction Not ForNot Table of Contents Read the Manual Operator Safety Operating SafetyNot Orf ChildrenC il renReproductioReversenFuel and MaintenanceReproduction Thrown Objects Operator Safety Slope OperationMoving Parts Protection Against Tip-Overs/Roll-Overs Operator SafetyProtection for Children Operation PreparationSafe Handling of Gasoline Maintenance TowingFor Safety and Instructional Decals Reproduction ForExplanation of Safety Decals Explanation of Instructional DecalsFor Not Features and Controls Features and ControlsBefore Starting How To Check/Add OilOperation Before adding or checking the oilHow To Add Fuel How To Adjust The Operator SeatFuel Recommendations How To Start The Engine How To Engage The Mower Blade ForwardMower Blade EngineTransmission How To Set The Parking Brake Reverse Mowing Option RMO DeflectorRepr Oduction How To Push The Unit By HandTowing Implements Maintanance Chart MaintenanceEmissions Control How To Change The Oil Filter if EquippedFlat Air Filter How To Service The Air FilterNotB Oval Air FilterRider Maintenance Basic How To Check The Mower Blade Rider Maintenance AdvancedHow To Service The Fuel Filter How To Check The Mower Drive BeltsHow To Lubricate Mower Blade Spindle How To Lubricate Grease FittingsHow To Lubricate Differential / Chain How To Lubricate Mower Deck LinkageHow To Install The Battery Battery Service Sealed Lead Acid TypeHow To Remove The Battery How To Charge The Battery How To Store The BatteryBattery Service Valve Regulated Type Battery valve regulated typeFuel System StorageBriggs & Stratton Fresh Start available in a drip con How To Sharpen The Mower Blade Engine Adjustments and RepairsRider Adjustments And Repairs How To Inspect The Mower BladeRepair How To Level The Mower DeckReproduction B Side-To-Side LevelingManual Drive Models How To Adjust The Brake / Parking BrakeHow To Adjust Mower Blade Belt Tension Hydro Drive ModelsHow To Adjust The Blade Brake How To Remove The Deck Cover Troubleshooting Problem Probable Cause Corrective ActionTroubleshooting Limited Warranty WarrantiesBriggs & Stratton Emissions Control Warranty Provisions Page Page 4.5 / 1,6 7,2 0 / 0 8,0

7800918-00, 7800920-00, 7800932-00 specifications

The Snapper 7800920-00, 7800918-00, and 7800932-00 represent a series of high-performance mowers designed for both residential and commercial use. These models leverage advanced technologies and engineering, making them some of the most reliable and efficient choices on the market for lawn care enthusiasts and professionals alike.

One of the standout features of the Snapper 7800 series is their powerful engine options. Most models in this range are equipped with reliable Briggs & Stratton engines, known for their durability and easy starting capabilities. This ensures that users can tackle tough mowing jobs with confidence, whether dealing with thick grass, uneven terrain, or large lawns.

The cutting deck of these mowers is another significant highlight. The Snapper 7800920-00 features a 21-inch steel cutting deck that provides a clean and even cut, improving the overall appearance of your lawn. The other models, 7800918-00 and 7800932-00, offer a similar design with slight variations suited for different mowing needs. The adjustable cutting height allows users to customize the lawn cut based on personal preferences or seasonal requirements.

In terms of usability, these mowers come with ergonomic handles designed for comfort during prolonged use. The handles are often adjustable, catering to different user heights and improving maneuverability across various lawn types. The self-propelled feature, present in many models, allows easy navigation across slopes or uneven ground, making these mowers suitable for a variety of landscapes.

Snapper also integrates innovative technologies that enhance operational efficiency. Features such as efficient bagging systems allow for easy grass collection while reducing the need for raking afterward. The mulching capability, prevalent in these models, provides an eco-friendly solution by returning grass clippings to the lawn, promoting healthier growth.

Safety is another priority with Snapper's design ethos. These mowers are equipped with safety features such as blade brake systems and easily accessible controls that ensure users can operate the machines safely and effectively.

In conclusion, the Snapper 7800920-00, 7800918-00, and 7800932-00 incorporate advanced engineering, powerful performance, and user-friendly features that cater to the needs of both casual lawn caretakers and professional landscapers. With their strong build quality, reliability, and array of capabilities, these models stand out as excellent investments for maintaining pristine outdoor spaces.
Top Page Image Contents