Snapper 7800918-00, 7800932-00, 7800920-00 manual Operation, Before Starting, How To Check/Add Oil

Page 14
Safety Interlock System Checks

Operation

Before Starting

Make the following checks and perform the service required before each start-up:

1.Check the tire pressure; add or release air as need- ed. Refer to “How To Check Tire Pressure” in the Maintenance section.

2.Check guards, deflectors and covers to make sure all are in place and securely tightened.

3.Check engine oil and add oil as needed. Refer to “How To Check/Add Oil”.

4.Add fuel to the fuel tank as needed. Refer to “How to Add Fuel”.

5.Adjust the operator seat as needed to the most comfort- able position. Refer to “How To Adjust The Operator Seat”.

6.Check all operator controls to ensure they operate freely without binding.

7.Perform the Safety Interlock System Checks. Refer to “Safety Interlock System Checks”.

*Below 40°F (4°C) the use of SAE 30 will result in hard starting.

**Above 80°F (27°C) the use of 10W-30 may cause increased oil consumption. Check oil level more frequently.

How To Check/Add Oil

Before adding or checking the oil

•Place engine level.

•Clean the oil fill area of any debris.

1.Remove the dipstick (A, Figure 1) and wipe with a clean cloth.

 

 

 

 

 

 

NOTE: On some models, the dipstick is accessible through

 

!

WARNING

 

!

an opening behind the operator seat.

 

 

2. Insert and tighten the dipstick.

DO NOT operate machine if any safety interlock or safety

3. Remove the dipstick and check the oil level. It should be

device is not in place and functioning properly. Contact

at the top of the full indicator (B) on the dipstick.

your dealer immediately for assistance. DO NOT attempt to

4. If low, add oil slowly into the engine oil fill (C). Do not

defeat, modify or remove any safety device.

 

overfill. After adding oil, wait one minute and then

Engine must not start if:

 

 

 

recheck the oil level.

 

 

 

 

5. Replace and tighten the dipstick.

1.

The Clutch/Brake Pedal is not fully depressed OR,

 

 

2.

The Blade Control is in the ON (engaged) position.

 

 

Engine should start if:

 

 

 

 

 

1.

The operator is seated in the operator seat AND,

 

 

2.

 

 

 

 

for

 

 

The Blade Control is in the OFF (disengaged) position

 

 

3.

AND,

 

 

 

 

 

 

The Clutch/Brake Pedal is fully depressed.

 

 

Engine and blade must stop if:

 

 

 

 

1.

The operator rises off of the operator seat OR,

 

 

2.

The operator attempts to drive the unit in reverse with

C

 

 

 

 

Not

 

A

 

the mower blade engaged and the reverse mowing

 

 

option function (RMO) not activated.

 

 

 

Oil Recommendations

ReproductionA

 

We recommend the use of Briggs & Stratton Warranty

 

 

Certified oils for best performance. Other high-quality deter-

B

 

gent oils are acceptable if classified for service SF,

 

SG, SH, SJ or higher. Do not use special additives.

 

 

Outdoor temperatures determine the proper oil viscosity for

 

 

the engine. Use the chart to select the best viscosity for the

 

 

outdoor temperature range expected.

 

 

Figure 1: Engine oil

 

 

 

 

 

 

 

 

14

www.snapper.com

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Reproduction Not ForNot Table of Contents Read the Manual Operator Safety Operating SafetyNot Orf ChildrenC il renReproductioReversenMoving Parts Operator Safety Slope OperationFuel and MaintenanceReproduction Thrown Objects Protection for Children Operator SafetyProtection Against Tip-Overs/Roll-Overs Safe Handling of Gasoline PreparationOperation Maintenance TowingFor Safety and Instructional Decals Reproduction ForExplanation of Safety Decals Explanation of Instructional DecalsFor Not Features and Controls Features and ControlsBefore Starting How To Check/Add OilOperation Before adding or checking the oilFuel Recommendations How To Adjust The Operator SeatHow To Add Fuel How To Start The Engine How To Engage The Mower Blade ForwardTransmission EngineMower Blade How To Set The Parking Brake Reverse Mowing Option RMO DeflectorTowing Implements How To Push The Unit By HandRepr Oduction Emissions Control MaintenanceMaintanance Chart How To Change The Oil Filter if EquippedFlat Air Filter How To Service The Air FilterNotB Oval Air FilterRider Maintenance Basic How To Check The Mower Blade Rider Maintenance AdvancedHow To Service The Fuel Filter How To Check The Mower Drive BeltsHow To Lubricate Mower Blade Spindle How To Lubricate Grease FittingsHow To Lubricate Differential / Chain How To Lubricate Mower Deck LinkageHow To Install The Battery Battery Service Sealed Lead Acid TypeHow To Remove The Battery How To Charge The Battery How To Store The BatteryBattery Service Valve Regulated Type Battery valve regulated typeBriggs & Stratton Fresh Start available in a drip con StorageFuel System How To Sharpen The Mower Blade Engine Adjustments and RepairsRider Adjustments And Repairs How To Inspect The Mower BladeRepair How To Level The Mower DeckReproduction B Side-To-Side LevelingManual Drive Models How To Adjust The Brake / Parking BrakeHow To Adjust Mower Blade Belt Tension Hydro Drive ModelsHow To Adjust The Blade Brake How To Remove The Deck Cover Troubleshooting Problem Probable Cause Corrective ActionTroubleshooting Limited Warranty WarrantiesBriggs & Stratton Emissions Control Warranty Provisions Page Page 4.5 / 1,6 7,2 0 / 0 8,0

7800918-00, 7800920-00, 7800932-00 specifications

The Snapper 7800920-00, 7800918-00, and 7800932-00 represent a series of high-performance mowers designed for both residential and commercial use. These models leverage advanced technologies and engineering, making them some of the most reliable and efficient choices on the market for lawn care enthusiasts and professionals alike.

One of the standout features of the Snapper 7800 series is their powerful engine options. Most models in this range are equipped with reliable Briggs & Stratton engines, known for their durability and easy starting capabilities. This ensures that users can tackle tough mowing jobs with confidence, whether dealing with thick grass, uneven terrain, or large lawns.

The cutting deck of these mowers is another significant highlight. The Snapper 7800920-00 features a 21-inch steel cutting deck that provides a clean and even cut, improving the overall appearance of your lawn. The other models, 7800918-00 and 7800932-00, offer a similar design with slight variations suited for different mowing needs. The adjustable cutting height allows users to customize the lawn cut based on personal preferences or seasonal requirements.

In terms of usability, these mowers come with ergonomic handles designed for comfort during prolonged use. The handles are often adjustable, catering to different user heights and improving maneuverability across various lawn types. The self-propelled feature, present in many models, allows easy navigation across slopes or uneven ground, making these mowers suitable for a variety of landscapes.

Snapper also integrates innovative technologies that enhance operational efficiency. Features such as efficient bagging systems allow for easy grass collection while reducing the need for raking afterward. The mulching capability, prevalent in these models, provides an eco-friendly solution by returning grass clippings to the lawn, promoting healthier growth.

Safety is another priority with Snapper's design ethos. These mowers are equipped with safety features such as blade brake systems and easily accessible controls that ensure users can operate the machines safely and effectively.

In conclusion, the Snapper 7800920-00, 7800918-00, and 7800932-00 incorporate advanced engineering, powerful performance, and user-friendly features that cater to the needs of both casual lawn caretakers and professional landscapers. With their strong build quality, reliability, and array of capabilities, these models stand out as excellent investments for maintaining pristine outdoor spaces.
Top Page Image Contents