Snapper EP2167517BV, ERP2167517BV important safety instructions Pulley Position

Page 18

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

4.4.1.Engine Drive Belt Replacement (Stretch Type Belts)

(Continued From Previous Page)

IMPORTANT: Drain fuel before tipping mower. DO NOT tip machine with carburetor or spark plug down. Oil from crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occur, the air filter will have to be replaced.

3. Remove the driven disc. Refer to Section

“Replacing Rubber Driven Disc Ring” for driven disc

assembly removal procedure.

4. Tilt mower up on its rear wheels and remove

blade and blade hub. Assistance from another

person may be necessary to hold mower in the tilted

9.Loop the belt around the pulley on the bottom of the drive disc.

10.Reinstall drive disc and retaining hardware. IMPORTANT: 1) The square shoulder of the drive disc bolt must fit into the square hole of the bushing. 2) The square end of bushing must fit into the bracket slot.

11.Reinstall belt cover and tighten bolts securely.

12.Reinstall blade hub and cutter blade. Recommended torque for blade cap screw is 40 ft. lbs.

4.4.2.Transmission Poly-V Belt Replacement 1. Remove the driven disc. Refer to Section on “Replacing Driven Disc Rubber Ring” for procedure. 2. Note the routing of the old belt around the three pulleys before removing it. See Figure 4.17.

3. Place new Poly-V Belt over end of hex shaft and onto driven pulley.

4. Work belt onto top of idler pulley.

5. Twist belt sideways and pull it upward between the differential bracket and drive pulley and then down into the pulley groove. Make sure the Poly-V Belt is above belt guide. See Figure 4.17.

position.

5. Hold the slotted end of the drive disc bolt with a

DRIVE

IDLER

PULLEY DIFFERENTIAL BRACKET

screwdriver and remove the nut and internal tooth

lock washer. See Figure 4.16.

6.

Remove the belt cover located under deck.

7.

Lift the drive disc up and remove worn belt.

8.

Loop one end of new belt over engine pulley and

insert the other end through slot in deck. See Figure

4.15.

 

PULLEY POSITION

PULLEYPOLY-V BELT

HEX SHAFT

 

BELT GUIDE

DRIVEN

 

PULLEY

 

DRIVE DISC

 

 

 

 

ROUTING OF POLY-V BELT

SLOT IN END

 

FIGURE 4.17

BUSHING

 

OF DRIVE DISC

 

 

 

BOLT

 

 

BOLT RETAINER

DECK BRACKET (PARTIALLY SHOWN)

INTERNAL TOOTH LOCKWASHER

NUT

FIGURE 4.16

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents European 21 Steel Deck Walk Mowers Series Model Number ExplanationProtection for Children Slope OperationPreparation Maintenance and Storage OperationTable of Contents Familiarization Introduction NomenclatureOperating Instructions PRE-START Check ListStarting & Operation 2.2.1. Engine & Blade Primer Models Propelling Mower Cutting Height AdjustmentHandle Height Adjustment Self Propelled Models OnlySecure Adapter To Deck with Nuts Nuts Introduction Check Grease Level in Transmission MaintenanceService After First 5 Hours Change Engine OILCheck Mower Blade Service AnnuallyStorage Procedure Check Engine Drive BeltBlade Sharpening Repair & AdjustmentsMower Blade Replacement 4.1.1. Standard Blade Wear Limit 1.A. Ninja Blade Wear LimitWheel Drive Control Adjustment Cleaning Drive Disc & Driven Disc Driven and Drive Disc ServiceDriven Disc Adjustment Drive Spring Repair/ReplacementReplacing Rubber Driven Disc Drive Disc Assembly Install NEW Driven Disc Snap Rings Belt Service Pulley Position Troubleshooting Problem Probable Cause Corrective ActionMAINTENANCE/REPLACEMENT Parts Service Performed EachClean Sponge Element Engine Manual 100Decal Identification European Performance Year Limited Warranty Disclaimer of WarrantyEuropean Steel Deck Walk Behind Mowers Series

EP2167517BV, ERP2167517BV specifications

The Snapper EP2167517BV, also known as ERP2167517BV, is a powerful and reliable product designed for efficiency and durability in various applications. Engineered with precision, this model stands out for its assortment of features, innovative technologies, and robust characteristics.

One of the primary features of the Snapper EP2167517BV is its advanced engine technology. This model is equipped with a high-performance engine that provides optimal power output, enabling smooth operation even under heavy loads. The engine's efficiency not only contributes to a reduction in fuel consumption but also ensures minimal emissions, making it environmentally friendly.

The Snapper EP2167517BV also boasts a user-friendly design, combining ergonomics with functionality. The control panel is intuitively laid out, allowing operators to easily navigate through various functions. Adjustable handles provide users with enhanced comfort during operation, reducing fatigue during extended periods of use. The overall construction of the equipment is robust, built to withstand the rigors of demanding work environments.

Another noteworthy technology incorporated in the Snapper EP2167517BV is the advanced cutting system. This system allows for precise and uniform cutting, ensuring that tasks are completed efficiently and effectively. The sharp blades are crafted from high-quality materials, promoting longevity and performance over time. The model’s cutting height can be easily adjusted to accommodate different grass lengths, providing versatility for various landscaping tasks.

Durability is a cornerstone of the Snapper EP2167517BV’s design. Constructed from premium materials, this model is designed to endure harsh conditions and heavy usage. The robust frame reinforces its stability, while the rust-resistant components ensure longevity, reducing the need for frequent replacements or repairs.

In terms of maintenance, the Snapper EP2167517BV simplifies the upkeep process. Its easily accessible components allow for straightforward servicing, promoting optimal performance and extending the lifespan of the product. Additionally, the manufacturer provides comprehensive support and guidance, making it easier for users to maintain their equipment in peak condition.

In summary, the Snapper EP2167517BV, or ERP2167517BV, is a high-performance product characterized by its advanced engine technology, user-friendly design, efficient cutting system, and durable construction. These features collectively elevate its capability, making it an ideal choice for both professional landscapers and homeowners alike. Whether tackling tough jobs or maintaining aesthetics, this model delivers exceptional results and reliability.
Top Page Image Contents