Snapper EP2167517BV, ERP2167517BV Check Mower Blade, Check Engine Drive Belt, Service Annually

Page 11

Section 3 – MAINTENANCE

3.2.2.CHECK GREASE LEVEL IN TRANSMISSION (Continued from previous page)

NOTE: Do not spill grease or oil on surface of drive disc. See Figure 3.3.

3.Reinstall transmission plug.

4.Check grease level after each 25 hours of operation.

KEEP DRIVE DISC CLEAN !

FIGURE 3.3

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

IMPORTANT: DO NOT tip machine with carburetor or spark plug down. Oil from crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occur, the air filter will have to be replaced.

3.2.3. CHECK MOWER BLADE

1.Disconnect spark plug wire and secure end away from plug.

2.Tilt mower up on its rear wheels for access to the blade cap screw. Do not tilt mower with spark plug or carburetor down. See Figure 3.4.

3.Check torque of blade retaining cap screw. Recommended torque should be 40 ft. lbs. See Figure 3.4.

4.Check blade for sharpness, wear and damage. Refer to Section “Blade Wear Limits”.

3.2.4. CHECK ENGINE DRIVE BELT

1.Visually check engine drive belt for cracking, fraying, severed or belt strands exposed. If worn or damaged, replace belt before operating mower.

3.2.5. CHECK TRANSMISSION POLY-V BELT

1.Visually check poly-v belt for cracking, fraying, severed or belt strands exposed. If worn or damaged, replace belt before operating mower.

RECOMMENDED BLADE RETAINING CAP SCREW TORQUE VALUE SHOULD BE

40 FT. LBS.

FIGURE 3.4

3.3 SERVICE - ANNUALLY

Perform all maintenance as described in the “Service Schedule” section of this manual.

3.3.1. Engine

Service engine according to engine owner’s manual.

3.3.2. Air Filter

Refer to engine owner’s manual for service instructions.

3.3.3. Engine Oil

Refer to engine owner’s manual for service instructions.

3.4 STORAGE PROCEDURE

Refer to the Engine Owner’s Manual for directions regarding engine storage preparations. Prepare the mower for “end of season” storage as follows:

1.Drain fuel from fuel tank and let engine run until all fuel is out of the carburetor.

2.Disconnect and remove the spark plug wire away from spark plug before any other preparations are made!

3.Tape all openings closed to prevent spraying water into exhaust or air intakes during washing.

4.Tilt mower up on its rear wheels and thoroughly clean the underside of the deck. Do not tilt mower with spark plug or carburetor down. Scrape away any accumulation of grass with a putty knife and or wire brush.

5.Lubricate all exposed metal with a light coating of oil to prevent corrosion.

6.On self-propelled models disconnect transfer rod clip and remove ground speed control rod before folding handles.

7.Loosen handle knobs. Carefully fold the handles forward, “flexing” the control cables to prevent cable damage.

8.Store the mower in a shed or other dry area, protected from weather.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model Number Explanation European 21 Steel Deck Walk Mowers SeriesPreparation Protection for ChildrenSlope Operation Operation Maintenance and StorageTable of Contents Introduction Nomenclature FamiliarizationStarting & Operation 2.2.1. Engine & Blade Primer Models Operating InstructionsPRE-START Check List Self Propelled Models Only Cutting Height AdjustmentHandle Height Adjustment Propelling MowerSecure Adapter To Deck with Nuts Nuts Change Engine OIL MaintenanceService After First 5 Hours Introduction Check Grease Level in TransmissionCheck Engine Drive Belt Service AnnuallyStorage Procedure Check Mower Blade1.A. Ninja Blade Wear Limit Repair & AdjustmentsMower Blade Replacement 4.1.1. Standard Blade Wear Limit Blade SharpeningWheel Drive Control Adjustment Drive Spring Repair/Replacement Driven and Drive Disc ServiceDriven Disc Adjustment Cleaning Drive Disc & Driven DiscReplacing Rubber Driven Disc Drive Disc Assembly Install NEW Driven Disc Snap Rings Belt Service Pulley Position Problem Probable Cause Corrective Action Troubleshooting100 Service Performed EachClean Sponge Element Engine Manual MAINTENANCE/REPLACEMENT PartsDecal Identification European Performance Disclaimer of Warranty Year Limited WarrantyEuropean Steel Deck Walk Behind Mowers Series

EP2167517BV, ERP2167517BV specifications

The Snapper EP2167517BV, also known as ERP2167517BV, is a powerful and reliable product designed for efficiency and durability in various applications. Engineered with precision, this model stands out for its assortment of features, innovative technologies, and robust characteristics.

One of the primary features of the Snapper EP2167517BV is its advanced engine technology. This model is equipped with a high-performance engine that provides optimal power output, enabling smooth operation even under heavy loads. The engine's efficiency not only contributes to a reduction in fuel consumption but also ensures minimal emissions, making it environmentally friendly.

The Snapper EP2167517BV also boasts a user-friendly design, combining ergonomics with functionality. The control panel is intuitively laid out, allowing operators to easily navigate through various functions. Adjustable handles provide users with enhanced comfort during operation, reducing fatigue during extended periods of use. The overall construction of the equipment is robust, built to withstand the rigors of demanding work environments.

Another noteworthy technology incorporated in the Snapper EP2167517BV is the advanced cutting system. This system allows for precise and uniform cutting, ensuring that tasks are completed efficiently and effectively. The sharp blades are crafted from high-quality materials, promoting longevity and performance over time. The model’s cutting height can be easily adjusted to accommodate different grass lengths, providing versatility for various landscaping tasks.

Durability is a cornerstone of the Snapper EP2167517BV’s design. Constructed from premium materials, this model is designed to endure harsh conditions and heavy usage. The robust frame reinforces its stability, while the rust-resistant components ensure longevity, reducing the need for frequent replacements or repairs.

In terms of maintenance, the Snapper EP2167517BV simplifies the upkeep process. Its easily accessible components allow for straightforward servicing, promoting optimal performance and extending the lifespan of the product. Additionally, the manufacturer provides comprehensive support and guidance, making it easier for users to maintain their equipment in peak condition.

In summary, the Snapper EP2167517BV, or ERP2167517BV, is a high-performance product characterized by its advanced engine technology, user-friendly design, efficient cutting system, and durable construction. These features collectively elevate its capability, making it an ideal choice for both professional landscapers and homeowners alike. Whether tackling tough jobs or maintaining aesthetics, this model delivers exceptional results and reliability.
Top Page Image Contents