Snapper EP2167517BV, ERP2167517BV Drive Disc Assembly Install NEW Driven Disc Snap Rings

Page 16

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

4.3.4.Replacing Rubber Driven Disc (Continued from previous page)

2.Using needle nose pliers, unhook the drive spring and slide the driven disc assembly off the hex shaft. See Figure 4.12.

3.Remove the two snap rings which secure the rubber driven disc to the driven disc assembly. See Figure 4.13.

4.Install new rubber driven disc onto driven disc assembly with retaining rings.

5.Reverse above procedures for reassembly and installation of driven disc assembly.

4.3.5.Replacing Bearing In Driven Disc Assembly IMPORTANT: The bearing, on these “M” series machines, is staked into the thrust plate. The bearing will have to be driven out with a mallet and a large punch. A new bearing with four retaining screws will have to be purchased to replace existing bearing.

If the driven disc bearing requires replacement, remove the driven disc assembly and replace bearing as follows:

1. Using a small flat blade screwdriver, free the clip from the transfer rod. Then remove the transfer rod from the clip and the speed control rod. See Figure 4.11.

2. Using needle nose pliers, unhook the drive spring and slide the driven disc assembly off the hex shaft. See Figure 4.12.

3. Remove both snap rings that secure rubber driven disc hub to thrust plate. See Figure 4.13.

4. Slide the rubber driven disc hub out of the bearing.

5. Drive out existing bearing.

6. Install new bearing and secure to thrust plate with four retaining screws. Tighten screws securely. 7. Reassemble components in reverse order.

DRIVE DISC

ASSEMBLY

INSTALL NEW

DRIVEN DISC

SNAP

RINGS

FIGURE 4.12

FIGURE 4.13

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents European 21 Steel Deck Walk Mowers Series Model Number ExplanationSlope Operation Protection for ChildrenPreparation Maintenance and Storage OperationTable of Contents Familiarization Introduction NomenclaturePRE-START Check List Operating InstructionsStarting & Operation 2.2.1. Engine & Blade Primer Models Cutting Height Adjustment Handle Height AdjustmentPropelling Mower Self Propelled Models OnlySecure Adapter To Deck with Nuts Nuts Maintenance Service After First 5 HoursIntroduction Check Grease Level in Transmission Change Engine OILService Annually Storage ProcedureCheck Mower Blade Check Engine Drive BeltRepair & Adjustments Mower Blade Replacement 4.1.1. Standard Blade Wear LimitBlade Sharpening 1.A. Ninja Blade Wear LimitWheel Drive Control Adjustment Driven and Drive Disc Service Driven Disc AdjustmentCleaning Drive Disc & Driven Disc Drive Spring Repair/ReplacementReplacing Rubber Driven Disc Drive Disc Assembly Install NEW Driven Disc Snap Rings Belt Service Pulley Position Troubleshooting Problem Probable Cause Corrective ActionService Performed Each Clean Sponge Element Engine ManualMAINTENANCE/REPLACEMENT Parts 100Decal Identification European Performance Year Limited Warranty Disclaimer of WarrantyEuropean Steel Deck Walk Behind Mowers Series

EP2167517BV, ERP2167517BV specifications

The Snapper EP2167517BV, also known as ERP2167517BV, is a powerful and reliable product designed for efficiency and durability in various applications. Engineered with precision, this model stands out for its assortment of features, innovative technologies, and robust characteristics.

One of the primary features of the Snapper EP2167517BV is its advanced engine technology. This model is equipped with a high-performance engine that provides optimal power output, enabling smooth operation even under heavy loads. The engine's efficiency not only contributes to a reduction in fuel consumption but also ensures minimal emissions, making it environmentally friendly.

The Snapper EP2167517BV also boasts a user-friendly design, combining ergonomics with functionality. The control panel is intuitively laid out, allowing operators to easily navigate through various functions. Adjustable handles provide users with enhanced comfort during operation, reducing fatigue during extended periods of use. The overall construction of the equipment is robust, built to withstand the rigors of demanding work environments.

Another noteworthy technology incorporated in the Snapper EP2167517BV is the advanced cutting system. This system allows for precise and uniform cutting, ensuring that tasks are completed efficiently and effectively. The sharp blades are crafted from high-quality materials, promoting longevity and performance over time. The model’s cutting height can be easily adjusted to accommodate different grass lengths, providing versatility for various landscaping tasks.

Durability is a cornerstone of the Snapper EP2167517BV’s design. Constructed from premium materials, this model is designed to endure harsh conditions and heavy usage. The robust frame reinforces its stability, while the rust-resistant components ensure longevity, reducing the need for frequent replacements or repairs.

In terms of maintenance, the Snapper EP2167517BV simplifies the upkeep process. Its easily accessible components allow for straightforward servicing, promoting optimal performance and extending the lifespan of the product. Additionally, the manufacturer provides comprehensive support and guidance, making it easier for users to maintain their equipment in peak condition.

In summary, the Snapper EP2167517BV, or ERP2167517BV, is a high-performance product characterized by its advanced engine technology, user-friendly design, efficient cutting system, and durable construction. These features collectively elevate its capability, making it an ideal choice for both professional landscapers and homeowners alike. Whether tackling tough jobs or maintaining aesthetics, this model delivers exceptional results and reliability.
Top Page Image Contents