Snapper LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV Introduction, Change Engine OIL

Page 12

Section 3 - MAINTENANCE

3.1 INTRODUCTION

To retain the quality of the Tractor, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular Tractor, always mention the model and serial number. SNAPPER recommends returning the Tractor to an authorized SNAPPER dealer annually for inspection

“ADJUSTING MOWER BLADE”.

5.Check torque of blade mounting bolts. Torque to: 33” deck – 30 to 40 ft. lbs. See Figure 3.2.

38” deck – 70 to 80 ft. lbs. See Figure 3.3.

and addition of any new devices, which might upgrade the safety of the Tractor. For the nearest SNAPPER dealer in your area, check the yellow pages under the heading LAWN MOWERS. For engine parts and service, look for the engine manufacturer’s dealers under the heading, ENGINES - gasoline.

3.2 SERVICE - AFTER FIRST 5 HOURS

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blades running. STOP blades. STOP engine. Set park brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

3.2.1. CHANGE ENGINE OIL

The engine is equipped with a Fastex™ oil drain.

ROTATE COUNTER- CLOCKWISE AND PULL OUT TO OPEN.

PUSH IN AND ROTATE CLOCKWISE TO CLOSE.

OIL

FILLER

TUBE

FASTEX™

OIL DRAIN

NOTE: BRIGGS & STRATTON ENGINE PICTURED

1.Rotate drain body counterclockwise and pull out to open drain. See Figure 3.1.

2.Drain oil into a 2 quart container placed beneath end of oil drain.

3.After all oil has drained, push drain body "IN" and rotate clockwise to close.

4.Fill engine with new motor oil as specified in engine owner's manual.

WARNING

The following procedure requires the engine and blades to be operated. Exercise extreme caution. Clear area of loose parts & tools first. Only operate blades when seated in the operator’s seat.

3.2.2. CHECK BLADE BRAKE

1.Check blade brake for proper function. Blades should stop rotating in 5 seconds or less after moving the blade engagement lever down to the OFF position.

2.If blades continue to rotate longer than 5 seconds do not operate machine. Refer to Section “BLADE BRAKE ADJUSTMENT” or contact your SNAPPER dealer for assistance.

3.2.3. CHECK MOWER BLADE

1.Remove deck from tractor.

2.Carefully position deck to access blade.

3.Check blade for sharpness, wear and damage. Refer to Section “BLADE WEAR LIMITS”.

4.Check blade for straightness. Refer to Section

FIGURE 3.1

TORQUE 33” BLADE TO 30 TO 40 FT. LBS.

FIGURE 3.2

WARNING

Blades must stop rotating in 5 seconds or less after blades have been turned off. DO NOT operate machine until blade brake has been adjusted and functioning properly. Contact your SNAPPER dealer for assistance.

13

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model Number Explanation 150Protection for Children Protection Against TipoversPreparation Maintenance OperationTable of Contents Components ControlsPRE-START Checklist OPERATOR’S Seat Adjustment Front to Rear AdjustmentStarting & Operation Starting Engine OFFStarting & Operation 2.3.2. Starting Wheel Drive Starting Mower BladeStopping Wheel Drive Setting Park Brake Cutting Height AdjustmentStopping Stopping Mower Blade Releasing Park BrakeRolling Tractor with Engine OFF 2.6.1. Rolling Hydro Models Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideService After First 5 Hours IntroductionChange Engine OIL Check Blade BrakeService Every 25 Operating Hours Check Engine Check Mower BladeCheck 33 Deck Drive Belt Check 38 Deck Drive BeltMower Components Tractor LubricationService Annually Service Annually 3.4.2. Fuel Filter Service Annually 3.4.2. Fuel Filter From PreviousSpark Plug Hydrostatic Transmission OIL Engine Adjustments & Repair Blade Brake AdjustmentDeck Blade Brake Adjustment Blade Belt Adjustment 33 Deck Blade Belt Adjustment 38 DeckOn next Adjusting Mower Blade 33 Deck from previous Side View of DeckDeck Level Adjustment Side to Side Deck Level Adjustment Front to Rear Sector PlatesDeck Level Adjustment Front to Rear Front Lift ROD From previousFront of Tractor Deck Level Adjustment Front to Rear Tractor Drive Components Brake AdjustmentRear to Front View of Deck Steering Adjustment Shifter AdjustmentMounting Mower Blade Service Standard Blade Wear Limits Ninja Blade Wear LimitsStandard Blade Sharpening Ninja Blade SharpeningMower Blade Replacement Traction Drive Belt Replacement Mower Deck RemovalTraction drive belt removal Traction drive belt replacement View from Underneath TractorDeck Drive Belt Battery Battery Removal Battery InstallationBattery Service Battery StorageBattery Testing NEW Battery PreparationAvailable Accessories Available LT150H33IBV LT150H38IBV AccessoriesSchematic Wiring Harness P.N Schematic Wiring Harness P.N LT150H38HKVLT150H33IBV & LT150H38IBV Troubleshooting Guide Problem Probable Cause Corrective ActionTroubleshooting Guide Tractor Drive Belts Mower Blades NinjaWLT150H38IBV WLT170H38IBVYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Service Notes Lawn Tractor Hydrostatic Drive Series

LT150H33IBV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV, LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV specifications

The Snapper LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV, LT150H33IBV, and WLT170H38IBV are part of Snapper's robust lineup of lawn tractors designed for residential and commercial landscaping needs. These models are engineered for efficiency, durability, and comfort, making them perfect for tackling various mowing tasks.

One of the standout features across these models is the powerful engine options. Equipped with reliable Briggs & Stratton engines, these tractors provide ample horsepower to handle tough mowing conditions. The LT150H331BV and LT150H38IBV boast a 150cc engine that delivers dependable performance, while the WLT170H38IBV features a more powerful 170cc engine, allowing for increased cutting speeds and improved overall efficiency.

The cutting deck on these models varies, with sizes generally around 38 inches to 42 inches, offering a balance between maneuverability and cutting capacity. The mulching capability is another significant advantage, allowing homeowners to recycle grass clippings, which promotes healthier lawns. Many of these tractors also feature adjustable cutting height settings, providing versatility for different grass types and mowing conditions.

Ergonomics play a crucial role in user satisfaction, and Snapper has designed these models with comfortable padded seats and easy-to-reach controls. The availability of hydrostatic transmission in models like the WLT150H38IBV allows for smooth speed adjustments, enhancing the user experience during operation.

In terms of technology, these Snapper lawn tractors often incorporate smart cut technology, which automatically adjusts the engine speed based on the mowing conditions. This feature not only results in a cleaner cut but also aids in fuel efficiency. The compact design of these tractors ensures easier storage and maneuverability around landscaping obstacles.

Durability is at the forefront of Snapper’s construction, with heavy-duty steel frames and reinforced decks designed to withstand regular use. These models are also backed by Snapper's reputation for quality, ensuring users can rely on their performance for many seasons.

In summary, the Snapper LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV, LT150H33IBV, LT150H38IBV, and WLT170H38IBV offer a blend of power, comfort, and innovative features. Whether you are maintaining a small residential lawn or a larger area, these tractors provide the reliability and efficiency needed for effective lawn care.
Top Page Image Contents