Snapper LT150H33IBV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV Battery Testing

Page 31

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT OVERFILL! DO NOT attempt to service or charge the battery while it is installed on the machine. DO NOT use “BOOST” chargers on the battery.

4.5.5.BATTERY TESTING

There are two types of battery tests: Unloaded and Loaded. The unloaded test is the procedure that will be discussed. It’s the simplest and most commonly used. An unloaded test is made on a battery without discharging current. To perform unloaded testing, check charge condition using either a hydrometer or voltmeter.

1.Using a voltmeter, voltage readings appear instantly to show the state of charge. Remember to hook the positive lead to the battery’s positive terminal, and the negative lead to the negative terminal.

2.A hydrometer measures the specific gravity of each cell. The specific gravity tells the degree of charge; generally, a specific gravity of about 1.265 to 1.280 indicates full charge. A reading of 1.230 to 1.260 indicates the battery should be charged. The Battery Condition chart below shows the charge level as measured by syringe float hydrometer, digital voltmeter and five ball hydrometer.

4.5.6NEW BATTERY PREPARATION

1.Remove battery from carton.

2.Place battery in a well ventilated area on a level non- concrete surface.

3.Remove battery cell caps. Fill cells as required with electrolyte (purchased separately) to proper level. Fill to 3/16” above cell plates. Filling battery with electrolyte will bring the battery to 80% charged state.

4.With cell caps removed, connect battery charger to battery terminals; RED to positive (+) and BLACK to negative (-) terminal.

IMPORTANT: 3/16” above cell plates is the recommended level. However do not try to measure this dimension. Never place anything in battery other than specified electrolyte.

5.Slow charge the battery at 1 amp for 2 hours to bring the battery to full charge.

6.After charging, check level of electrolyte and add as needed to bring level to 3/16” above cell plates.

7.Reinstall cell caps.

8.Slide battery partially into battery housing.

9.Connect positive (+) cable (red) first, from wiring harness to the positive terminal (+) on battery using bolt and nut provided in hardware bag. Connect negative (-) cable (black) last, to negative terminal (-) on battery using bolt and nut. Apply a small amount of grease over terminals to prevent corrosion.

10.Insert battery completely into battery housing.

11.Reinstall seat assembly.

WARNING

Shield the positive terminal with terminal cover located on battery harness. This prevents metal from touching the positive terminal, which could cause sparks. Cables must be connected to battery terminals in the proper position. RED (Positive) cable must go to the ( + ) terminal. BLACK (Negative) cable must go to the ( - ) terminal.

Battery Condition Chart

 

State of Charge

Syringe Hydrometer

Digital Voltmeter

Five Ball Hydrometer

100%

Charged w/ Sulfate Stop

1.280

12.80v

Five Balls Floating

100%

Charged

1.265

12.60v

Four Balls Floating

75% Charged

1.210

12.40v

Three Balls Floating

50% Charged

1.160

12.10v

Two Balls Floating

25% Charged

1.120

11.90v

One Ball Floating

0% Charged

Less than 1.100

Less than 11.80v

Zero Balls Floating

32

Image 31
Contents 150 Model Number ExplanationProtection Against Tipovers Protection for ChildrenPreparation Operation MaintenanceTable of Contents Controls ComponentsOPERATOR’S Seat Adjustment Front to Rear Adjustment PRE-START ChecklistOFF Starting & Operation Starting EngineStarting Mower Blade Starting & Operation 2.3.2. Starting Wheel DriveStopping Wheel Drive Releasing Park Brake Setting Park BrakeCutting Height Adjustment Stopping Stopping Mower BladeRolling Tractor with Engine OFF 2.6.1. Rolling Hydro Models Reverse Lockout Mechanism Override Reverse Lockout MechanismCheck Blade Brake Service After First 5 HoursIntroduction Change Engine OILCheck 38 Deck Drive Belt Service Every 25 Operating Hours Check EngineCheck Mower Blade Check 33 Deck Drive BeltTractor Lubrication Mower ComponentsService Annually Service Annually 3.4.2. Fuel Filter From Previous Service Annually 3.4.2. Fuel FilterSpark Plug Hydrostatic Transmission OIL Blade Brake Adjustment Engine Adjustments & RepairDeck Blade Brake Adjustment Blade Belt Adjustment 38 Deck Blade Belt Adjustment 33 DeckOn next Side View of Deck Adjusting Mower Blade 33 Deck from previousFrom previous Deck Level Adjustment Side to SideDeck Level Adjustment Front to Rear Sector Plates Deck Level Adjustment Front to Rear Front Lift RODFront of Tractor Tractor Drive Components Brake Adjustment Deck Level Adjustment Front to RearRear to Front View of Deck Shifter Adjustment Steering AdjustmentMounting Ninja Blade Sharpening Mower Blade Service Standard Blade Wear LimitsNinja Blade Wear Limits Standard Blade SharpeningTraction Drive Belt Replacement Mower Deck Removal Mower Blade ReplacementTraction drive belt removal View from Underneath Tractor Traction drive belt replacementDeck Drive Belt Battery Storage Battery Battery RemovalBattery Installation Battery ServiceNEW Battery Preparation Battery TestingAvailable LT150H33IBV LT150H38IBV Accessories Available AccessoriesSchematic Wiring Harness P.N LT150H38HKV Schematic Wiring Harness P.NLT150H33IBV & LT150H38IBV Problem Probable Cause Corrective Action Troubleshooting GuideTroubleshooting Guide WLT170H38IBV Tractor Drive Belts Mower BladesNinja WLT150H38IBVDisclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Service Notes Lawn Tractor Hydrostatic Drive Series

LT150H33IBV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV, LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV specifications

The Snapper LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV, LT150H33IBV, and WLT170H38IBV are part of Snapper's robust lineup of lawn tractors designed for residential and commercial landscaping needs. These models are engineered for efficiency, durability, and comfort, making them perfect for tackling various mowing tasks.

One of the standout features across these models is the powerful engine options. Equipped with reliable Briggs & Stratton engines, these tractors provide ample horsepower to handle tough mowing conditions. The LT150H331BV and LT150H38IBV boast a 150cc engine that delivers dependable performance, while the WLT170H38IBV features a more powerful 170cc engine, allowing for increased cutting speeds and improved overall efficiency.

The cutting deck on these models varies, with sizes generally around 38 inches to 42 inches, offering a balance between maneuverability and cutting capacity. The mulching capability is another significant advantage, allowing homeowners to recycle grass clippings, which promotes healthier lawns. Many of these tractors also feature adjustable cutting height settings, providing versatility for different grass types and mowing conditions.

Ergonomics play a crucial role in user satisfaction, and Snapper has designed these models with comfortable padded seats and easy-to-reach controls. The availability of hydrostatic transmission in models like the WLT150H38IBV allows for smooth speed adjustments, enhancing the user experience during operation.

In terms of technology, these Snapper lawn tractors often incorporate smart cut technology, which automatically adjusts the engine speed based on the mowing conditions. This feature not only results in a cleaner cut but also aids in fuel efficiency. The compact design of these tractors ensures easier storage and maneuverability around landscaping obstacles.

Durability is at the forefront of Snapper’s construction, with heavy-duty steel frames and reinforced decks designed to withstand regular use. These models are also backed by Snapper's reputation for quality, ensuring users can rely on their performance for many seasons.

In summary, the Snapper LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV, LT150H33IBV, LT150H38IBV, and WLT170H38IBV offer a blend of power, comfort, and innovative features. Whether you are maintaining a small residential lawn or a larger area, these tractors provide the reliability and efficiency needed for effective lawn care.