Snapper LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV Deck Level Adjustment Front to Rear

Page 22

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

4.2.9.38" DECK LEVEL ADJUSTMENT (FRONT TO REAR)

1.Position the blades as shown. See Figure 4.16.

FRONT OF TRACTOR

LEFT FRONT

BLADE TIP

RIGHT REAR BLADE TIP

FIGURE 4.16

2.Measure the distance from the left front blade tip to the ground and from the right rear blade tip to the ground. The front left blade tip should be between 1/8" and 3/8" higher than the right rear (factory setting). If it is between 1/8" and 3/8" you are finished with adjustment.

3.If it is not within specifications, adjust by raising or lowering the front of the deck using the swivel on the front lift rod. Turning the swivel clockwise will raise the front of the deck. Turning the swivel counterclockwise will lower the front of the deck.

NOTE: The deck should be set so that the rear of the deck is 1/4" lower than the front. See Figure 4.17.

REAR TO FRONT VIEW OF DECK

 

X

X - 1/8”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ANGLE IRON

FIGURE 4.17

4.3 TRACTOR DRIVE COMPONENTS

4.3.1.BRAKE ADJUSTMENT

When adjusted properly, the brake should stop the tractor in approximately 6 feet or less from top speed. Drive the machine at maximum forward speed and apply the brake. If stopping distance is greater than 6 feet, brake adjustment is required.

1.Turn engine “OFF”. Remove key.

2.Locate brake adjustment nut underneath the left side at the rear of tractor. See Figure 4.18.

3.Turn nut 1 turn clockwise to increase braking action. DO NOT over tighten brake adjustment.

4.Start engine and test brake.

5.Continue adjustment as described above until proper brake function is achieved.

ROTATE ADJUSTING NUT CLOCKWISE TO

INCREASE BRAKING OR COUNTER

CLOCKWISE TO DECREASE BRAKING

FIGURE 4.18

23

Image 22
Contents Model Number Explanation 150Protection Against Tipovers Protection for ChildrenPreparation Maintenance OperationTable of Contents Components ControlsPRE-START Checklist OPERATOR’S Seat Adjustment Front to Rear AdjustmentStarting & Operation Starting Engine OFFStarting Mower Blade Starting & Operation 2.3.2. Starting Wheel DriveStopping Wheel Drive Stopping Stopping Mower Blade Setting Park BrakeCutting Height Adjustment Releasing Park BrakeRolling Tractor with Engine OFF 2.6.1. Rolling Hydro Models Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideChange Engine OIL Service After First 5 HoursIntroduction Check Blade BrakeCheck 33 Deck Drive Belt Service Every 25 Operating Hours Check EngineCheck Mower Blade Check 38 Deck Drive BeltMower Components Tractor LubricationService Annually Service Annually 3.4.2. Fuel Filter From Previous Service Annually 3.4.2. Fuel FilterSpark Plug Hydrostatic Transmission OIL Blade Brake Adjustment Engine Adjustments & RepairDeck Blade Brake Adjustment Blade Belt Adjustment 38 Deck Blade Belt Adjustment 33 DeckOn next Adjusting Mower Blade 33 Deck from previous Side View of DeckDeck Level Adjustment Front to Rear Front Lift ROD Deck Level Adjustment Side to SideDeck Level Adjustment Front to Rear Sector Plates From previousFront of Tractor Tractor Drive Components Brake Adjustment Deck Level Adjustment Front to RearRear to Front View of Deck Steering Adjustment Shifter AdjustmentMounting Standard Blade Sharpening Mower Blade Service Standard Blade Wear LimitsNinja Blade Wear Limits Ninja Blade SharpeningMower Blade Replacement Traction Drive Belt Replacement Mower Deck RemovalTraction drive belt removal Traction drive belt replacement View from Underneath TractorDeck Drive Belt Battery Service Battery Battery RemovalBattery Installation Battery StorageBattery Testing NEW Battery PreparationAvailable Accessories Available LT150H33IBV LT150H38IBV AccessoriesSchematic Wiring Harness P.N LT150H38HKV Schematic Wiring Harness P.NLT150H33IBV & LT150H38IBV Troubleshooting Guide Problem Probable Cause Corrective ActionTroubleshooting Guide WLT150H38IBV Tractor Drive Belts Mower BladesNinja WLT170H38IBVYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Service Notes Lawn Tractor Hydrostatic Drive Series

LT150H33IBV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV, LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV specifications

The Snapper LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV, LT150H33IBV, and WLT170H38IBV are part of Snapper's robust lineup of lawn tractors designed for residential and commercial landscaping needs. These models are engineered for efficiency, durability, and comfort, making them perfect for tackling various mowing tasks.

One of the standout features across these models is the powerful engine options. Equipped with reliable Briggs & Stratton engines, these tractors provide ample horsepower to handle tough mowing conditions. The LT150H331BV and LT150H38IBV boast a 150cc engine that delivers dependable performance, while the WLT170H38IBV features a more powerful 170cc engine, allowing for increased cutting speeds and improved overall efficiency.

The cutting deck on these models varies, with sizes generally around 38 inches to 42 inches, offering a balance between maneuverability and cutting capacity. The mulching capability is another significant advantage, allowing homeowners to recycle grass clippings, which promotes healthier lawns. Many of these tractors also feature adjustable cutting height settings, providing versatility for different grass types and mowing conditions.

Ergonomics play a crucial role in user satisfaction, and Snapper has designed these models with comfortable padded seats and easy-to-reach controls. The availability of hydrostatic transmission in models like the WLT150H38IBV allows for smooth speed adjustments, enhancing the user experience during operation.

In terms of technology, these Snapper lawn tractors often incorporate smart cut technology, which automatically adjusts the engine speed based on the mowing conditions. This feature not only results in a cleaner cut but also aids in fuel efficiency. The compact design of these tractors ensures easier storage and maneuverability around landscaping obstacles.

Durability is at the forefront of Snapper’s construction, with heavy-duty steel frames and reinforced decks designed to withstand regular use. These models are also backed by Snapper's reputation for quality, ensuring users can rely on their performance for many seasons.

In summary, the Snapper LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV, LT150H33IBV, LT150H38IBV, and WLT170H38IBV offer a blend of power, comfort, and innovative features. Whether you are maintaining a small residential lawn or a larger area, these tractors provide the reliability and efficiency needed for effective lawn care.