Snapper FRP216016 important safety instructions Wheel Drive Control Adjustment

Page 12

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

4.Sharpen blade on a grinding wheel at an angle of

22to 28 degrees. DO NOT sharpen blade beyond original cutting edge. See Figure 4.3.

DO NOT SHARPEN

BEYOND ORIGINAL

CUTTING EDGE

22-28º

BLADE TIP

END VIEW OF

BLADE ASSEMBLY

ORIGINAL CUTTING EDGE

FIGURE 4.4

5.Check blade for balance. If necessary, correct balance by grinding heavy end of blade.

6.Reinstall blade. See Figure 4.1. Check torque of blade retaining cap screw. Recommended torque should be 30 to 40 ft. lbs.

CLUTCH CABLE

 

VINYL SPRING

 

1/16” TO 1/8”

CLUTCH CABLE

CLEARANCE

EYE

UPPER

 

SPRING

SPRING HOOK

 

LOWER

 

SPRING

 

CABLE

CLUTCH CABLE EYE

SPRING

FIGURE 4.4

2.To adjust, unhook upper spring from cable eye and rotate spring in direction required to extend or shorten spring length.

3.Rehook upper spring to cable eye and check clearance. Repeat procedure if required.

NOTE: The vinyl spring cover should be kept over the spring at all times except for adjustments.

NOTE: The following sections 4.2 through 4.4 are for self-propelled models only.

4.2WHEEL DRIVE CONTROL ADJUSTMENT

1. The wheel drive control is properly adjusted when there is 1/16” to 1/8” clearance between the inside of the spring hook and the inside of the clutch cable eye with the wheel drive control released. See Figure 4.4.

4.If the wheel drive control fails to return quickly to the “OFF” position when released, check for binding at the cable holdings located on the side of the right handle. The upper clip should be located 2” below the upper knob; the lower clip should be 4” above the lower knob. The cable should slide freely with the clips installed at these locations.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Steel Deck Walk Mowers Series Important Safety Instructions Operation Table of Contents Introduction NomenclaturePRE-START Check List Starting & Operation 2.2.1. Engine & BladePrimer Models Cutting Height Adjustment Handle Height AdjustmentPropelling Mower StoppingAdjusting Front Deck Baffle Installation of Grass CatcherRecycling Operation Models with an F prefix in model numberService After First 5 Hours 3.2.1. Change Engine OIL On NextService Annually Storage ProcedureCheck Mower Blade Check Engine Drive BeltMower Blade Replacement 4.1.1. Standard Blade Wear Limit Blade Sharpening1A. Ninja Blade Wear Limit Wheel Drive Control Adjustment Driven Disc Service Driven Disc AdjustmentCleaning Drive Disc & Driven Disc Drive Spring Repair/ReplacementReplacing Rubber Driven Disc Ring Replacing Rubber Driven Disc Ring From Previous Belt Service Drive Idler Pulley Differential Bracket Troubleshooting Problem Probable Cause Corrective ActionService Performed Each Clean Sponge Element Engine ManualMAINTENANCE/REPLACEMENT Parts 100Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Page Page Page Steel Deck Walk Behind Mowers Series

FRP216016 specifications

The Snapper FRP216016 is a versatile and innovative lawn mower designed to enhance the efficiency of lawn care for both residential and commercial users. One of its standout features is the powerful 21-inch cutting deck, which is engineered to deliver a clean and precise cut across various types of grass and terrain. This size allows for optimum maneuverability, making it ideal for small to medium-sized lawns while still having the capacity to manage larger spaces effectively.

Equipped with a reliable 160cc engine, the FRP216016 ensures robust performance, enabling it to handle tough mowing conditions without compromising on power. This engine features advanced technology that not only provides ample torque but also promotes fuel efficiency, translating to longer run times and reduced operational costs.

The Snapper FRP216016 also incorporates the innovative SureCut technology, which enhances the cutting experience by preventing grass clumping, resulting in a well-manicured lawn. This unique design helps to disperse clippings more evenly, minimizing the need for additional clean-up after mowing.

Another key characteristic of the FRP216016 is its height adjustment feature, allowing users to customize the cut to their preference with ease. The mower offers multiple cutting height positions, accommodating various grass types and seasonal preferences. This flexibility is crucial for achieving the perfect lawn look while ensuring optimal health of the grass.

Additionally, the ergonomic handle design contributes to user comfort during operation. This mower is lightweight and easy to maneuver, reducing fatigue during longer mowing sessions. Snapper also focuses on user-friendly features, including an easy-start system that enables users to begin mowing with minimal effort.

The snapper FRP216016 is also designed with durability in mind, featuring high-quality materials that resist wear and tear over time. This durability ensures that the mower remains a reliable tool in your lawn care arsenal for years to come.

In conclusion, the Snapper FRP216016 lawn mower is an excellent choice for individuals seeking power, efficiency, and ease of use in their lawn care routines. With features tailored to meet the demands of various mowing conditions, it stands out as a top contender in the realm of residential and light commercial mowing equipment. Whether you're maintaining your yard or managing a small golf course, the Snapper FRP216016 is engineered to exceed expectations.
Top Page Image Contents