Snapper LT145H33FBV, LT145H38FBV Introduction, Service After First 5 Hours, Change Engine OIL

Page 11

Section 3 - MAINTENANCE

3.1 INTRODUCTION

To retain the quality of the Tractor, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular Tractor, always mention the model and serial number. SNAPPER recommends returning the Tractor to an authorized SNAPPER dealer annually for inspection and addition of any new devices, which might upgrade the safety of the Tractor. For the nearest SNAPPER dealer in your area, check the yellow pages under the heading LAWN MOWERS. For engine parts and service, look for the engine manufacturer’s dealers under the heading, ENGINES - gasoline.

3.2 SERVICE - AFTER FIRST 5 HOURS

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blades running. STOP blades. STOP engine. Set park brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

3.2.1. CHANGE ENGINE OIL

These model tractors are equipped Fastex™ oil drains.

1.Rotate drain body counterclockwise and pull out to open drain. See Figure 3.1.

2.Drain oil into a 2 quart container placed beneath end of oil drain.

3.After all oil has drained, push drain body "IN" and rotate clockwise to close.

4.Fill engine with new motor oil as specified in engine owner's manual.

4.Check blade for straightness. Refer to Section

“ADJUSTING MOWER BLADE”.

5.Check torque of blade mounting bolts. Torque to: 33” deck – 30 to 40 ft. lbs. See Figure 3.2.

38” deck – 70 to 80 ft. lbs. See Figure 3.3.

OIL

FILLER

TUBE

FASTEX™

OIL DRAIN

ROTATE COUNTER-

CLOCKWISE AND PULL

OUT TO OPEN.

PUSH IN AND ROTATE

CLOCKWISE TO CLOSE.

FIGURE 3.1

WARNING

The following procedure requires the engine and blades to be operated. Exercise extreme caution. Clear area of loose parts & tools first. Only operate blades when seated in the operator’s seat.

3.2.2. CHECK BLADE BRAKE

1.Check blade brake for proper function. Blades should stop rotating in 5 seconds or less after moving the blade engagement lever down to the OFF position.

2.If blades continue to rotate longer than 5 seconds do not operate machine. Refer to Section “BLADE BRAKE ADJUSTMENT” or contact your SNAPPER dealer for assistance.

3.2.3. CHECK MOWER BLADE

1.Remove deck from tractor.

2.Carefully position deck to access blade.

3.Check blade for sharpness, wear and damage. Refer to Section “BLADE WEAR LIMITS”.

11

TORQUE 33” BLADE TO 30 TO 40 FT. LBS.

FIGURE 3.2

WARNING

Blades must stop rotating in 5 seconds or less after blades have been turned off. DO NOT operate machine until blade brake has been adjusted and functioning properly. Contact your SNAPPER dealer for assistance.

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model Number Explanation Lawn Tractor Hydrostatic Drive Series FImportant Safety Instructions Operation Table of Contents Controls ComponentsOPERATOR’S Seat Adjustment Front to Rear Adjustment PRE-START ChecklistOFF Starting & Operation Starting EngineStopping Wheel Drive Starting & Operation 2.3.2. Starting Wheel DriveStarting Mower Blade Stopping ENGINE, BLADE, Wheel Drive 2.4.1 Stopping EngineReleasing Park Brake Setting Park BrakeCutting Height Adjustment Stopping Stopping Mower BladeRolling Tractor with Engine OFF Rolling Hydro Models Check Blade Brake Service After First 5 HoursIntroduction Change Engine OILCheck 38 Deck Drive Belt Service Every 25 Operating HoursCheck Engine Check 33 Deck Drive BeltTractor Lubrication Fuel Filter Service AnnuallySpark Plug Hydrostatic Transmission OIL Service Annually 3.4.2. Fuel FilterFrom Previous Deck Blade Brake Adjustment Engine Adjustments & RepairBlade Brake Adjustment On next Blade Belt Adjustment 33 DeckBlade Belt Adjustment 38 Deck Side View of Deck Adjusting Mower Blade 33 Deck from previousDeck Level Adjustment Front to Rear Front Lift ROD Deck Level Adjustment Side to SideDeck Level Adjustment Front to Rear Sector Plates Front of Tractor Rear to Front View of Deck Deck Level Adjustment Front to RearTractor Drive Components 4.3.1. Brake Adjustment Shifter Adjustment Steering AdjustmentAdjustment & Repair Ninja Blade Sharpening Mower Blade Service Standard Blade Wear LimitsNinja Blade Wear Limits Standard Blade SharpeningTraction Drive Belt Replacement Mower Deck Removal Mower Blade ReplacementTraction drive belt removal View from Underneath Tractor Traction drive belt replacementDeck Drive Belt Battery Storage Battery Battery RemovalBattery Installation Battery ServiceNEW Battery Preparation Battery TestingAvailable Accessories Harness Routing Electrical SystemSchematics Troubleshooting Guide Troubleshooting Guide LT145H38FBV Tractor Drive Belts Mower BladesNinja LT145H33FBVYear Limited Warranty Primary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Lawn Tractor Hydrostatic Drive Series F

LT145H38FBV, LT145H33FBV, LT145H33FBV, LT145H38FBV specifications

The Snapper LT145H33FBV and LT145H38FBV are part of Snapper's renowned line of riding mowers, designed for homeowners seeking performance, efficiency, and reliability in lawn care. These models are characterized by a range of features and technologies that cater to both novice and experienced users.

One of the most prominent features of the LT145H series is its powerful engine. The LT145H33FBV is equipped with a robust 33-inch cutting deck, while the LT145H38FBV boasts a slightly larger 38-inch cutting deck, allowing users to optimize their mowing efficiency across various lawn sizes. These engines are designed with efficiency in mind, ensuring that grass is cut cleanly and evenly, while also minimizing fuel consumption.

The Snapper LT145H series utilizes a hydrostatic transmission system, which provides a smooth driving experience. This technology allows users to adjust the speed of the mower easily without the need for shifting gears, making it simpler to navigate around obstacles and tight spaces in the yard. The intuitive controls are user-friendly, ensuring that even those unfamiliar with riding mowers can operate them comfortably.

Comfort plays an essential role in the design of the LT145H series. Both models come with an ergonomic seat that provides support and reduces fatigue during extended mowing sessions. Additionally, adjustable seats allow users to customize their riding position for maximum comfort. The steering wheel is designed to be accessible and easy to maneuver, enhancing the overall user experience.

Each model also features a durable steel frame, providing stability and longevity. The cutting decks are constructed to withstand the challenges of regular use, ensuring consistent performance over time. Features such as easy-to-access maintenance points make it simpler for users to perform routine upkeep, prolonging the mower's lifespan.

Moreover, the Snapper LT145H series is equipped with a mulching capability as an option. This allows for finely chopping grass clippings, which can be left on the lawn to decompose and nourish the soil, promoting a healthier lawn. In addition, both models come with the option of attaching grass catchers for those who prefer a clean finish.

In conclusion, the Snapper LT145H33FBV and LT145H38FBV are excellent choices for anyone seeking a reliable, efficient, and comfortable riding mower. With their powerful engines, advanced technologies, and user-oriented design, these models stand out as top contenders in the lawn care market. Whether you have a small yard or a larger property, the LT145H series caters to various needs, making lawn maintenance a more enjoyable task.
Top Page Image Contents