Snapper LT145H38FBV, LT145H33FBV Adjusting Mower Blade 33 Deck from previous, Side View of Deck

Page 18

Section 4 - ADJUSTMENT & REPAIR

4.2.4.ADJUSTING MOWER BLADE – 33” DECK (Continued from previous page)

MEASURE THE DISTANCE

BETWEEN DECK LIP AND

BLADE TIP

FIGURE 4.5

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

NOTE: On 33” decks, the measurement between the blade tip and deck lip should be 5/16".

5.Repeat steps 2 and 3 with blade tip “B”.

6.If measurement between blade tips and deck are different and there is more than 1/16” difference between blade tip measurements, adjust blade as follows:

a.Loosen jam-nuts on blade bar.

b.Adjust jack screws “IN” or “OUT” until blade tip measurements are within 1/16” of each other. See Figure 4.6.

c.Tighten jam-nuts.

LOOSEN JAM NUTS, ADJUST

JACK SCREWS “IN” OR “OUT”

TO LEVEL BLADE WITH DECK

JACK SCREW

JAM NUT

4.2.5.33" DECK LEVEL ADJUSTMENT (SIDE TO SIDE) NOTE: Adjust tire pressure, 12 P.S.I. front and rear, before adjusting deck.

1.Move tractor to a firm, level surface.

2.Turn engine "OFF". Remove key.

3.Place a piece of angle iron under center rear of deck.

4.Remove hair pins and washers securing rear of deck to sector plates. See Figure 4.7.

5.Slide sector off of pins and carefully lower deck onto angle iron.

6.Rotate blade(s) until blade tips are at each side of deck.

7.Measure distance from blade tip to floor on each side of deck. Blade tips should be within 1/8" of each other for the deck to be considered level. See Figure 4.8.

SECTOR PLATE

REMOVE

HAIRPIN &

WASHER

FIGURE 4.7

33” DECK SHOWN SIDE TO SIDE VIEW

MEASURE

ANGLE IRON

FROM BLADE

 

TIPS TO FLOOR

 

FIGURE 4.8

8.If measurement differs more than 1/8", adjust as follows:

a.Loosen front lift arm pivot bolt on front of right side rail. See Figure 4.9.

LOOSEN PIVOT BOLT

LOOSEN SHOULDER

BOLT

SIDE VIEW OF DECK

FIGURE 4.6

TURN ECCENTRIC

 

AS REQUIRED

 

FIGURE 4.9

 

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Lawn Tractor Hydrostatic Drive Series F Model Number ExplanationImportant Safety Instructions Operation Table of Contents Components ControlsPRE-START Checklist OPERATOR’S Seat Adjustment Front to Rear AdjustmentStarting & Operation Starting Engine OFFStopping ENGINE, BLADE, Wheel Drive 2.4.1 Stopping Engine Starting & Operation 2.3.2. Starting Wheel DriveStarting Mower Blade Stopping Wheel DriveStopping Stopping Mower Blade Setting Park BrakeCutting Height Adjustment Releasing Park BrakeRolling Tractor with Engine OFF Rolling Hydro Models Change Engine OIL Service After First 5 HoursIntroduction Check Blade BrakeCheck 33 Deck Drive Belt Service Every 25 Operating HoursCheck Engine Check 38 Deck Drive BeltTractor Lubrication Service Annually Fuel FilterService Annually 3.4.2. Fuel Filter From PreviousSpark Plug Hydrostatic Transmission OIL Engine Adjustments & Repair Blade Brake AdjustmentDeck Blade Brake Adjustment Blade Belt Adjustment 33 Deck Blade Belt Adjustment 38 DeckOn next Adjusting Mower Blade 33 Deck from previous Side View of DeckDeck Level Adjustment Side to Side Deck Level Adjustment Front to Rear Sector PlatesDeck Level Adjustment Front to Rear Front Lift ROD Front of Tractor Deck Level Adjustment Front to Rear Tractor Drive Components 4.3.1. Brake AdjustmentRear to Front View of Deck Steering Adjustment Shifter AdjustmentAdjustment & Repair Standard Blade Sharpening Mower Blade Service Standard Blade Wear LimitsNinja Blade Wear Limits Ninja Blade SharpeningMower Blade Replacement Traction Drive Belt Replacement Mower Deck RemovalTraction drive belt removal Traction drive belt replacement View from Underneath TractorDeck Drive Belt Battery Service Battery Battery RemovalBattery Installation Battery StorageBattery Testing NEW Battery PreparationAvailable Accessories Electrical System Harness RoutingSchematics Troubleshooting Guide Troubleshooting Guide LT145H33FBV Tractor Drive Belts Mower BladesNinja LT145H38FBVYear Limited Warranty Primary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Lawn Tractor Hydrostatic Drive Series F

LT145H38FBV, LT145H33FBV, LT145H33FBV, LT145H38FBV specifications

The Snapper LT145H33FBV and LT145H38FBV are part of Snapper's renowned line of riding mowers, designed for homeowners seeking performance, efficiency, and reliability in lawn care. These models are characterized by a range of features and technologies that cater to both novice and experienced users.

One of the most prominent features of the LT145H series is its powerful engine. The LT145H33FBV is equipped with a robust 33-inch cutting deck, while the LT145H38FBV boasts a slightly larger 38-inch cutting deck, allowing users to optimize their mowing efficiency across various lawn sizes. These engines are designed with efficiency in mind, ensuring that grass is cut cleanly and evenly, while also minimizing fuel consumption.

The Snapper LT145H series utilizes a hydrostatic transmission system, which provides a smooth driving experience. This technology allows users to adjust the speed of the mower easily without the need for shifting gears, making it simpler to navigate around obstacles and tight spaces in the yard. The intuitive controls are user-friendly, ensuring that even those unfamiliar with riding mowers can operate them comfortably.

Comfort plays an essential role in the design of the LT145H series. Both models come with an ergonomic seat that provides support and reduces fatigue during extended mowing sessions. Additionally, adjustable seats allow users to customize their riding position for maximum comfort. The steering wheel is designed to be accessible and easy to maneuver, enhancing the overall user experience.

Each model also features a durable steel frame, providing stability and longevity. The cutting decks are constructed to withstand the challenges of regular use, ensuring consistent performance over time. Features such as easy-to-access maintenance points make it simpler for users to perform routine upkeep, prolonging the mower's lifespan.

Moreover, the Snapper LT145H series is equipped with a mulching capability as an option. This allows for finely chopping grass clippings, which can be left on the lawn to decompose and nourish the soil, promoting a healthier lawn. In addition, both models come with the option of attaching grass catchers for those who prefer a clean finish.

In conclusion, the Snapper LT145H33FBV and LT145H38FBV are excellent choices for anyone seeking a reliable, efficient, and comfortable riding mower. With their powerful engines, advanced technologies, and user-oriented design, these models stand out as top contenders in the lawn care market. Whether you have a small yard or a larger property, the LT145H series caters to various needs, making lawn maintenance a more enjoyable task.
Top Page Image Contents