Front of Tractor

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

4.2.8.38" DECK LEVEL ADJUSTMENT (SIDE TO SIDE)

NOTE: Before adjusting deck, bring tire pressure to proper P.S.I.; front 12 P.S.I., rear 12 P.S.I..

1.Move tractor to a firm, level surface.

2.Turn engine “OFF”. Remove key.

3.Place a 2-1/2” tall block under the front of the deck centered between the front lift arms. See Figure 4.13.

2-1/2” TALL BLOCK

SIDE TO SIDE LEVEL CHECK POINTS

1-3/4” TALL BLOCK

FIGURE 4.13

4.Place a 1-3/4" tall block under the rear of the deck in the center. See Figure 4.13.

5.Position blades as shown and lower deck onto blocks. See Figure 4.13.

6.Disconnect the front lift rod and the rear hanger plates. See Figure 4.14.

7.Put the lift lever in the 3rd position from low cut.

8.Measure the distance from each blade tip to the floor. The measurements should be within 1/8" of each other. (Factory setting)

38” DECK

JAM NUT

WASHER

FRONT LIFT

ROD

HAIR PIN

FIGURE 4.14

9.If the difference is less than 1/8", go to next section, Front to rear level. If the difference is more than 1/8", adjust as described in the following steps.

10.Loosen the front adjuster nut until adjuster moves freely. Then tighten the nut until the adjuster moves only when moderate force is applied to one side of the deck. See Figure 4.15.

FRONT OF TRACTOR

ADJUSTER NUT

FIGURE 4.15

11.Adjust the side to side level of the blade tips by moving one side of the deck up or down as needed to obtain 1/8" or less side to side deck level.

12.After leveling deck, retighten the adjuster nut using

30to 40 ft. lbs.

13.Attach the rear hanger plates to the hole that most closely aligns with the pin on the deck lift bracket. Secure with washer and hair pin.

14.Adjust the swivel on the front lift rod until it lines up with the hole in the front lift bracket. (Make sure the lift rod is at the top of the slot in the deck bracket) Secure with hair pin.

LT145H38FBV, LT145H33FBV, LT145H33FBV, LT145H38FBV specifications

The Snapper LT145H33FBV and LT145H38FBV are part of Snapper's renowned line of riding mowers, designed for homeowners seeking performance, efficiency, and reliability in lawn care. These models are characterized by a range of features and technologies that cater to both novice and experienced users.

One of the most prominent features of the LT145H series is its powerful engine. The LT145H33FBV is equipped with a robust 33-inch cutting deck, while the LT145H38FBV boasts a slightly larger 38-inch cutting deck, allowing users to optimize their mowing efficiency across various lawn sizes. These engines are designed with efficiency in mind, ensuring that grass is cut cleanly and evenly, while also minimizing fuel consumption.

The Snapper LT145H series utilizes a hydrostatic transmission system, which provides a smooth driving experience. This technology allows users to adjust the speed of the mower easily without the need for shifting gears, making it simpler to navigate around obstacles and tight spaces in the yard. The intuitive controls are user-friendly, ensuring that even those unfamiliar with riding mowers can operate them comfortably.

Comfort plays an essential role in the design of the LT145H series. Both models come with an ergonomic seat that provides support and reduces fatigue during extended mowing sessions. Additionally, adjustable seats allow users to customize their riding position for maximum comfort. The steering wheel is designed to be accessible and easy to maneuver, enhancing the overall user experience.

Each model also features a durable steel frame, providing stability and longevity. The cutting decks are constructed to withstand the challenges of regular use, ensuring consistent performance over time. Features such as easy-to-access maintenance points make it simpler for users to perform routine upkeep, prolonging the mower's lifespan.

Moreover, the Snapper LT145H series is equipped with a mulching capability as an option. This allows for finely chopping grass clippings, which can be left on the lawn to decompose and nourish the soil, promoting a healthier lawn. In addition, both models come with the option of attaching grass catchers for those who prefer a clean finish.

In conclusion, the Snapper LT145H33FBV and LT145H38FBV are excellent choices for anyone seeking a reliable, efficient, and comfortable riding mower. With their powerful engines, advanced technologies, and user-oriented design, these models stand out as top contenders in the lawn care market. Whether you have a small yard or a larger property, the LT145H series caters to various needs, making lawn maintenance a more enjoyable task.