Snapper LT145H38FBV, LT145H33FBV Mower Blade Service Standard Blade Wear Limits

Page 24

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

4.4 MOWER BLADE SERVICE

4.4.1.(STANDARD) BLADE WEAR LIMITS

All mower blades should be checked for excessive wear and damage before each use. See Figure 4.23.

NOTCH FORMING

NEW

 

BLADE

 

WEAR LIMIT.

 

CUTTING EDGE

 

WORN.

 

DANGEROUS CONDITION! DO

 

NOT USE ON MOWER!

 

 

 

FIGURE 4.23

4.4.2.(NINJA) BLADE WEAR LIMITS

The ninja recycling blade requires more frequent service intervals than standard blades. Check for excessive wear and damage before each use. See Figure 4.24.

NEW

BLADE

WEAR LIMIT. (CRACKS

OR NOTCHES BEGIN

TO APPEAR)

4.4.3.(STANDARD) BLADE SHARPENING

Blades should be kept sharp at all times. When the blades are dull, cut grass will be ragged and lawn will usually turn brown. Sharpen standard blades as follows:

1.Move tractor to a firm, level surface.

2.Turn engine "OFF". Remove key.

3.Remove mowing deck from tractor.

4.Remove mower blade(s).

5.If a blade is in good condition, sharpen cutting edge at an angle of 22 to 28 degrees. DO NOT sharpen beyond existing cutting edge. Replace blades not in good condition. See Figure 4.25.

22º TO 28º

STANDARD BLADE

ORIGINAL CUTTING EDGE

FIGURE 4.25

4.4.4.(NINJA) BLADE SHARPENING

The Ninja recycling blades requires more frequent service intervals than standard blades. When the blades are dull, cut grass will be ragged and lawn will usually turn brown. Sharpen standard blades as follows:

1.Move tractor to a firm, level surface.

2.Turn engine "OFF". Remove key.

3.Remove mowing deck from tractor.

4.Remove mower blade(s).

5.Sharpen all cutting edges of the Ninja recycling blade at an angle of 22 to 28 degrees for optimum performance. See Figure 4.26.

NINJA BLADE

22º TO 28º

DANGEROUS CONDITION!

BLADE TIP

DO NOT USE ON MOWER!

 

FIGURE 4.24

FIGURE 4.26

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Lawn Tractor Hydrostatic Drive Series F Model Number ExplanationImportant Safety Instructions Operation Table of Contents Components ControlsPRE-START Checklist OPERATOR’S Seat Adjustment Front to Rear AdjustmentStarting & Operation Starting Engine OFFStarting & Operation 2.3.2. Starting Wheel Drive Starting Mower BladeStopping ENGINE, BLADE, Wheel Drive 2.4.1 Stopping Engine Stopping Wheel DriveSetting Park Brake Cutting Height AdjustmentStopping Stopping Mower Blade Releasing Park BrakeRolling Tractor with Engine OFF Rolling Hydro Models Service After First 5 Hours IntroductionChange Engine OIL Check Blade BrakeService Every 25 Operating Hours Check EngineCheck 33 Deck Drive Belt Check 38 Deck Drive BeltTractor Lubrication Service Annually Fuel FilterService Annually 3.4.2. Fuel Filter From PreviousSpark Plug Hydrostatic Transmission OIL Engine Adjustments & Repair Blade Brake AdjustmentDeck Blade Brake Adjustment Blade Belt Adjustment 33 Deck Blade Belt Adjustment 38 DeckOn next Adjusting Mower Blade 33 Deck from previous Side View of DeckDeck Level Adjustment Side to Side Deck Level Adjustment Front to Rear Sector PlatesDeck Level Adjustment Front to Rear Front Lift ROD Front of Tractor Deck Level Adjustment Front to Rear Tractor Drive Components 4.3.1. Brake AdjustmentRear to Front View of Deck Steering Adjustment Shifter AdjustmentAdjustment & Repair Mower Blade Service Standard Blade Wear Limits Ninja Blade Wear LimitsStandard Blade Sharpening Ninja Blade SharpeningMower Blade Replacement Traction Drive Belt Replacement Mower Deck RemovalTraction drive belt removal Traction drive belt replacement View from Underneath TractorDeck Drive Belt Battery Battery Removal Battery InstallationBattery Service Battery StorageBattery Testing NEW Battery PreparationAvailable Accessories Electrical System Harness RoutingSchematics Troubleshooting Guide Troubleshooting Guide Tractor Drive Belts Mower Blades NinjaLT145H33FBV LT145H38FBVYear Limited Warranty Primary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Lawn Tractor Hydrostatic Drive Series F

LT145H38FBV, LT145H33FBV, LT145H33FBV, LT145H38FBV specifications

The Snapper LT145H33FBV and LT145H38FBV are part of Snapper's renowned line of riding mowers, designed for homeowners seeking performance, efficiency, and reliability in lawn care. These models are characterized by a range of features and technologies that cater to both novice and experienced users.

One of the most prominent features of the LT145H series is its powerful engine. The LT145H33FBV is equipped with a robust 33-inch cutting deck, while the LT145H38FBV boasts a slightly larger 38-inch cutting deck, allowing users to optimize their mowing efficiency across various lawn sizes. These engines are designed with efficiency in mind, ensuring that grass is cut cleanly and evenly, while also minimizing fuel consumption.

The Snapper LT145H series utilizes a hydrostatic transmission system, which provides a smooth driving experience. This technology allows users to adjust the speed of the mower easily without the need for shifting gears, making it simpler to navigate around obstacles and tight spaces in the yard. The intuitive controls are user-friendly, ensuring that even those unfamiliar with riding mowers can operate them comfortably.

Comfort plays an essential role in the design of the LT145H series. Both models come with an ergonomic seat that provides support and reduces fatigue during extended mowing sessions. Additionally, adjustable seats allow users to customize their riding position for maximum comfort. The steering wheel is designed to be accessible and easy to maneuver, enhancing the overall user experience.

Each model also features a durable steel frame, providing stability and longevity. The cutting decks are constructed to withstand the challenges of regular use, ensuring consistent performance over time. Features such as easy-to-access maintenance points make it simpler for users to perform routine upkeep, prolonging the mower's lifespan.

Moreover, the Snapper LT145H series is equipped with a mulching capability as an option. This allows for finely chopping grass clippings, which can be left on the lawn to decompose and nourish the soil, promoting a healthier lawn. In addition, both models come with the option of attaching grass catchers for those who prefer a clean finish.

In conclusion, the Snapper LT145H33FBV and LT145H38FBV are excellent choices for anyone seeking a reliable, efficient, and comfortable riding mower. With their powerful engines, advanced technologies, and user-oriented design, these models stand out as top contenders in the lawn care market. Whether you have a small yard or a larger property, the LT145H series caters to various needs, making lawn maintenance a more enjoyable task.
Top Page Image Contents