Snapper LT145H33FBV, LT145H38FBV Deck Level Adjustment Front to Rear, Rear to Front View of Deck

Page 21

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

4.2.9.38" DECK LEVEL ADJUSTMENT (FRONT TO REAR)

1.Position the blades as shown. See Figure 4.16.

FRONT OF TRACTOR

LEFT FRONT

BLADE TIP

RIGHT REAR BLADE TIP

FIGURE 4.16

2.Measure the distance from the left front blade tip to the ground and from the right rear blade tip to the ground. The front left blade tip should be between 1/8" and 3/8" higher than the right rear (factory setting). If it is between 1/8" and 3/8" you are finished with adjustment.

3.If it is not within specifications, adjust by raising or lowering the front of the deck using the swivel on the front lift rod. Turning the swivel clockwise will raise the front of the deck. Turning the swivel counterclockwise will lower the front of the deck.

NOTE: The deck should be set so that the rear of the deck is 1/4" lower than the front. See Figure 4.17.

REAR TO FRONT VIEW OF DECK

 

X

X - 1/8”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ANGLE IRON

FIGURE 4.17

4.3TRACTOR DRIVE COMPONENTS 4.3.1. BRAKE ADJUSTMENT

1.To be properly adjusted, the brake should stop the tractor in approximately 6 feet or less from top speed when the clutch/brake pedal is fully depressed.

2.Adjust brake when necessary as follows:

3.Turn engine “OFF”. Remove key.

4.Locate brake adjustment nut underneath the rear of tractor. See Figure 4.18.

5.Turn nut clockwise to increase braking action or counterclockwise to decrease braking action.

6.Start engine and test brake.

7.Continue adjustment as described above until proper adjustment is achieved.

ROTATE ADJUSTING NUT CLOCKWISE TO

INCREASE BRAKING OR COUNTER

CLOCKWISE TO DECREASE BRAKING

FIGURE 4.18

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model Number Explanation Lawn Tractor Hydrostatic Drive Series FImportant Safety Instructions Operation Table of Contents Controls ComponentsOPERATOR’S Seat Adjustment Front to Rear Adjustment PRE-START ChecklistOFF Starting & Operation Starting EngineStarting Mower Blade Starting & Operation 2.3.2. Starting Wheel DriveStopping ENGINE, BLADE, Wheel Drive 2.4.1 Stopping Engine Stopping Wheel DriveCutting Height Adjustment Setting Park BrakeStopping Stopping Mower Blade Releasing Park BrakeRolling Tractor with Engine OFF Rolling Hydro Models Introduction Service After First 5 HoursChange Engine OIL Check Blade BrakeCheck Engine Service Every 25 Operating HoursCheck 33 Deck Drive Belt Check 38 Deck Drive BeltTractor Lubrication Fuel Filter Service AnnuallyService Annually 3.4.2. Fuel Filter From PreviousSpark Plug Hydrostatic Transmission OIL Engine Adjustments & Repair Blade Brake AdjustmentDeck Blade Brake Adjustment Blade Belt Adjustment 33 Deck Blade Belt Adjustment 38 DeckOn next Side View of Deck Adjusting Mower Blade 33 Deck from previousDeck Level Adjustment Side to Side Deck Level Adjustment Front to Rear Sector PlatesDeck Level Adjustment Front to Rear Front Lift ROD Front of Tractor Deck Level Adjustment Front to Rear Tractor Drive Components 4.3.1. Brake AdjustmentRear to Front View of Deck Shifter Adjustment Steering AdjustmentAdjustment & Repair Ninja Blade Wear Limits Mower Blade Service Standard Blade Wear LimitsStandard Blade Sharpening Ninja Blade SharpeningTraction Drive Belt Replacement Mower Deck Removal Mower Blade ReplacementTraction drive belt removal View from Underneath Tractor Traction drive belt replacementDeck Drive Belt Battery Installation Battery Battery RemovalBattery Service Battery StorageNEW Battery Preparation Battery TestingAvailable Accessories Harness Routing Electrical SystemSchematics Troubleshooting Guide Troubleshooting Guide Ninja Tractor Drive Belts Mower BladesLT145H33FBV LT145H38FBVYear Limited Warranty Primary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Lawn Tractor Hydrostatic Drive Series F

LT145H38FBV, LT145H33FBV, LT145H33FBV, LT145H38FBV specifications

The Snapper LT145H33FBV and LT145H38FBV are part of Snapper's renowned line of riding mowers, designed for homeowners seeking performance, efficiency, and reliability in lawn care. These models are characterized by a range of features and technologies that cater to both novice and experienced users.

One of the most prominent features of the LT145H series is its powerful engine. The LT145H33FBV is equipped with a robust 33-inch cutting deck, while the LT145H38FBV boasts a slightly larger 38-inch cutting deck, allowing users to optimize their mowing efficiency across various lawn sizes. These engines are designed with efficiency in mind, ensuring that grass is cut cleanly and evenly, while also minimizing fuel consumption.

The Snapper LT145H series utilizes a hydrostatic transmission system, which provides a smooth driving experience. This technology allows users to adjust the speed of the mower easily without the need for shifting gears, making it simpler to navigate around obstacles and tight spaces in the yard. The intuitive controls are user-friendly, ensuring that even those unfamiliar with riding mowers can operate them comfortably.

Comfort plays an essential role in the design of the LT145H series. Both models come with an ergonomic seat that provides support and reduces fatigue during extended mowing sessions. Additionally, adjustable seats allow users to customize their riding position for maximum comfort. The steering wheel is designed to be accessible and easy to maneuver, enhancing the overall user experience.

Each model also features a durable steel frame, providing stability and longevity. The cutting decks are constructed to withstand the challenges of regular use, ensuring consistent performance over time. Features such as easy-to-access maintenance points make it simpler for users to perform routine upkeep, prolonging the mower's lifespan.

Moreover, the Snapper LT145H series is equipped with a mulching capability as an option. This allows for finely chopping grass clippings, which can be left on the lawn to decompose and nourish the soil, promoting a healthier lawn. In addition, both models come with the option of attaching grass catchers for those who prefer a clean finish.

In conclusion, the Snapper LT145H33FBV and LT145H38FBV are excellent choices for anyone seeking a reliable, efficient, and comfortable riding mower. With their powerful engines, advanced technologies, and user-oriented design, these models stand out as top contenders in the lawn care market. Whether you have a small yard or a larger property, the LT145H series caters to various needs, making lawn maintenance a more enjoyable task.
Top Page Image Contents