Snapper MR216015T important safety instructions Wheel Drive Control Adjustment

Page 12

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

4.Sharpen blade on a grinding wheel at an angle of

22to 28 degrees. DO NOT sharpen blade beyond original cutting edge. See Figure 4.4.

DO NOT SHARPEN

BEYOND ORIGINAL

CUTTING EDGE

22 TO 28º

BLADE TIP

END VIEW OF

BLADE ASSEMBLY

ORIGINAL CUTTING EDGE

FIGURE 4.4

5.Check blade for balance. If necessary, correct balance by grinding heavy end of blade.

6.Reinstall blade. See Figure 4.3. Check torque of blade retaining cap screw. Recommended torque should be 30 to 40 ft. lbs.

NOTE: The following sections 4.2 through 4.4 are for self-propelled models only.

4.2WHEEL DRIVE CONTROL ADJUSTMENT

1. The wheel drive control is properly adjusted when there is 1/16” to 1/8” clearance between the inside of the spring hook and the inside of the clutch cable eye with the wheel drive control released. See Figure 4.5.

CLUTCH CABLE

 

VINYL SPRING COVER

 

1/16” TO 1/8”

CLUTCH

CABLE EYE

CLEARANCE

 

UPPER

SPRING HOOK

SPRING

LOWER

 

SPRING

 

CABLE

CLUTCH CABLE EYE

SPRING

FIGURE 4.5

2.To adjust, unhook upper spring from cable eye and rotate spring in direction required to extend or shorten spring length.

3.Rehook upper spring to cable eye and check clearance. Repeat procedure if required.

NOTE: The vinyl spring cover should be kept over the spring at all times except for adjustments.

4.If the wheel drive control fails to return quickly to the “OFF” position when released, check for binding at the cable holdings located on the side of the right handle. The upper clip should be located 2” below the upper knob; the lower clip should be 4” above the lower knob. The cable should slide freely with the clips installed at these locations.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Steel Deck Walk Mowers M Model Series Important Safety Instructions Operation Table of Contents Introduction NomenclaturePRE-START Check List Starting & Operation 2.2.1. Engine & BladePrimer Models Push & Non Commercial Self-Propelled Handle Height Adjustment Starting & Operation 2.2.2. Engine & BladeChoke ModelsCommercial Only Propelling MowerCutting Height Adjustment Recycling OperationService After First 5 Hours 3.2.1. Change Engine OIL Check Grease Level in TransmissionOn Next Service Annually Storage ProcedureCheck Mower Blade Check Engine Drive BeltMower Blade Replacement 4.1.1. Standard Blade Wear Limit Blade SharpeningNinja Blade Wear Limit Wheel Drive Control Adjustment Driven Disc Service Cleaning Drive Disc & Driven DiscDrive Spring Repair/Replacement Driven Disc AdjustmentReplacing Rubber Driven Disc Ring Replacing Bearing In Driven Disc Assembly Belt Service Engine Drive Belt Replacement Stretch Type BeltsTransmission Poly-V Belt Replacement Pulley PositionTroubleshooting Problem Probable Cause Corrective ActionService Performed Each Clean Sponge Element Engine ManualMAINTENANCE/REPLACEMENT Parts 100Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Page Page Page Steel Deck Walk Behind Mowers M Model Series

MR216015T specifications

The Snapper MR216015T is a versatile and powerful lawn mower designed for residential and commercial use. Renowned for its durability and performance, this model appeals to those seeking efficiency and dependability in lawn maintenance.

One of the standout features of the Snapper MR216015T is its robust 159cc Briggs & Stratton engine, which delivers reliable power for a variety of mowing tasks. This engine is designed for longevity and requires minimal maintenance, making it an appealing choice for those who prioritize ease of use.

The mower incorporates a 21-inch steel cutting deck, which not only ensures a wide cutting swath but also contributes to a professional-looking finish. The deck is engineered for durability and is complemented by a 3-in-1 cutting system, allowing users to choose from side discharge, mulching, or bagging options. This versatility ensures that mowing can be tailored to different lawn types and conditions, making it ideal for various outdoor spaces.

Another key feature of the Snapper MR216015T is its adjustable cutting height system. With six different height settings, users can easily adapt the mower to achieve the desired grass length, enhancing user control and lawn health. This feature is particularly beneficial for those with varying grass types or uneven terrains.

Ergonomics is also a focus in the design of this mower. The handle is adjustable and designed for comfort, allowing operators of different heights to operate the mower without strain. Additionally, the foldable design of the handle facilitates easy storage and transportation, which is an essential consideration for those with limited garage space.

The Snapper MR216015T is equipped with a reliable starting system, which enhances user convenience. Its easy pull-start mechanism ensures that the mower is ready to go when needed, eliminating the frustration of difficult starts often encountered with other models.

Lastly, the Snapper MR216015T has a reputation for being environmentally friendly due to its efficient design that optimizes fuel consumption while minimizing emissions. This makes it a responsible choice for environmentally conscious consumers.

In summary, the Snapper MR216015T lawn mower boasts a powerful engine, a durable cutting deck, adjustable height controls, user-friendly ergonomics, and an efficient starting system, making it a leading choice for anyone looking for reliability and performance in lawn care.
Top Page Image Contents