Snapper MR216015T important safety instructions Replacing Rubber Driven Disc Ring

Page 14

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

4.3.3.DRIVEN DISC ADJUSTMENT (Continued From Previous Page)

2.Remove driven disc spring from driven disc assembly. Loosen connector hex nut. See Figure 4.9.

DRIVEN DISC ASSEMBLY

DRIVE

DISC

DRIVEN

DISC

SPRING

TRANSFER

ROD

CONNECTOR

CONNECTOR

HEX NUT

FIGURE 4.9

3.Slide driven disc assembly over to 1/8” from outside edge of drive disc. Maintaining the 1/8” measurement, remove any looseness from the linkage. This can be done by holding the transfer rod and applying pressure to the left (as viewed from operators position). Then retighten the connector hex nut securely. See Figure

4.10.Move ground speed control to the first speed position, then back to the sixth speed position. Recheck the 1/8” measurement described previously. Reinstall driven disc spring to driven disc assembly.

1/8” MEASUREMENT TO

SLIDE DRIVEN

OUTSIDE EDGE OF

DISC ASSEMBLY

DRIVE DISC

TOWARD

 

OUTSIDE EDGE

DRIVE

 

DISC

TRANSFER

ROD

CONNECTOR HEX NUT

 

OUTSIDE

CONNECTOR

EDGE

 

FIGURE 4.10

4.3.4. Replacing Rubber Driven Disc Ring

If the rubber ring is badly chunked or worn down to within 1/16” of the metal rim of the driven disc hub, it must be replaced. Install new rubber ring as follows:

1.Using a small flat blade screwdriver, free the clip from the transfer rod. Then remove the transfer rod from the clip and the speed control rod. See Figure

CONNECTOR

CLIP

TRANSFER ROD

SPEED CONTROL

ROD

FIGURE 4.11

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Steel Deck Walk Mowers M Model Series Important Safety Instructions Operation Table of Contents Introduction NomenclaturePrimer Models Push & Non Commercial Self-Propelled PRE-START Check ListStarting & Operation 2.2.1. Engine & Blade Choke ModelsCommercial Only Handle Height AdjustmentStarting & Operation 2.2.2. Engine & Blade Propelling MowerCutting Height Adjustment Recycling OperationOn Next Service After First 5 Hours 3.2.1. Change Engine OILCheck Grease Level in Transmission Check Mower Blade Service AnnuallyStorage Procedure Check Engine Drive BeltNinja Blade Wear Limit Mower Blade Replacement 4.1.1. Standard Blade Wear LimitBlade Sharpening Wheel Drive Control Adjustment Drive Spring Repair/Replacement Driven Disc ServiceCleaning Drive Disc & Driven Disc Driven Disc AdjustmentReplacing Rubber Driven Disc Ring Replacing Bearing In Driven Disc Assembly Belt Service Engine Drive Belt Replacement Stretch Type BeltsTransmission Poly-V Belt Replacement Pulley PositionTroubleshooting Problem Probable Cause Corrective ActionMAINTENANCE/REPLACEMENT Parts Service Performed EachClean Sponge Element Engine Manual 100Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Page Page Page Steel Deck Walk Behind Mowers M Model Series

MR216015T specifications

The Snapper MR216015T is a versatile and powerful lawn mower designed for residential and commercial use. Renowned for its durability and performance, this model appeals to those seeking efficiency and dependability in lawn maintenance.

One of the standout features of the Snapper MR216015T is its robust 159cc Briggs & Stratton engine, which delivers reliable power for a variety of mowing tasks. This engine is designed for longevity and requires minimal maintenance, making it an appealing choice for those who prioritize ease of use.

The mower incorporates a 21-inch steel cutting deck, which not only ensures a wide cutting swath but also contributes to a professional-looking finish. The deck is engineered for durability and is complemented by a 3-in-1 cutting system, allowing users to choose from side discharge, mulching, or bagging options. This versatility ensures that mowing can be tailored to different lawn types and conditions, making it ideal for various outdoor spaces.

Another key feature of the Snapper MR216015T is its adjustable cutting height system. With six different height settings, users can easily adapt the mower to achieve the desired grass length, enhancing user control and lawn health. This feature is particularly beneficial for those with varying grass types or uneven terrains.

Ergonomics is also a focus in the design of this mower. The handle is adjustable and designed for comfort, allowing operators of different heights to operate the mower without strain. Additionally, the foldable design of the handle facilitates easy storage and transportation, which is an essential consideration for those with limited garage space.

The Snapper MR216015T is equipped with a reliable starting system, which enhances user convenience. Its easy pull-start mechanism ensures that the mower is ready to go when needed, eliminating the frustration of difficult starts often encountered with other models.

Lastly, the Snapper MR216015T has a reputation for being environmentally friendly due to its efficient design that optimizes fuel consumption while minimizing emissions. This makes it a responsible choice for environmentally conscious consumers.

In summary, the Snapper MR216015T lawn mower boasts a powerful engine, a durable cutting deck, adjustable height controls, user-friendly ergonomics, and an efficient starting system, making it a leading choice for anyone looking for reliability and performance in lawn care.
Top Page Image Contents