Snapper MR216015T important safety instructions Operation

Page 3

IMPORTANT SAFETY INSTRUCTIONS

OPERATION

1.DO NOT put hands or feet near or under rotating parts. Keep clear of discharge area while engine is running.

2.STOP engine when crossing gravel drives, walks, or roads, and under any conditions where thrown objects might be a hazard.

3.Mow only in daylight or good artificial light.

4.DO NOT operate mower while under the influence of alcohol or drugs.

5.After striking a foreign object or if mower vibrates abnormally, STOP the engine, disconnect and secure spark plug wire. Inspect the mower for any damage and repair the damage.

6.DO NOT mow near drop offs, ditches or embankments. Operator could lose footing or balance.

7.STAY ALERT for holes and other hidden hazards. Tall grass can hide obstacles. Keep away from ditches, washouts, culverts, fences and protruding objects.

8.DO NOT mow on wet grass. Always be sure of your footing. Keep a firm hold on the handle and walk, never run. Slipping could cause injury.

9.DO NOT leave the machine with the engine running. STOP BLADE and STOP ENGINE before leaving the operators position for any reason.

10.Before cleaning, repairing or inspecting make certain engine, blade and all moving parts have STOPPED. Disconnect and secure spark plug wire away from plug to prevent accidental starting.

11.STOP engine and wait until the blade comes to complete STOP before removing grass bag and/or clearing grass.

12.DO NOT operate mower without the entire grass catcher or guards in place. DO NOT point discharge at people, passing cars, windows or doors.

13.Slow down before turning.

14.Watch out for traffic when near or crossing roadways.

15.DO NOT operate engine in enclosed areas. Engine exhaust gases contain carbon monoxide, a deadly poison.

3

MAINTENANCE AND STORAGE

1.DO NOT store mower or fuel container inside where fumes may reach an open flame, spark or pilot light such as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of reach of children in a well ventilated, unoccupied building.

2.Keep mower and engine free of grass, leaves or excess grease to reduce fire hazard and engine overheating.

3.When draining fuel tank, drain fuel into an approved container outdoors and away from open flame.

4.Keep all bolts, especially blade bolts, nuts and screws properly tight. Check that all cotter pins are in proper position.

5.Always provide adequate ventilation when running engine. Engine exhaust gases contain carbon monoxide, a deadly poison.

6.Service engine and make adjustments only when engine is stopped. Removed spark plug wire from spark plug and secure wire away from spark plug to prevent accidental starting.

7.DO NOT change engine governor speed settings or overspeed engine.

8.Check grass bag assembly frequently for wear or deterioration to avoid thrown objects and exposure to moving parts. Replace with new bag if loose seams or tears are evident. Replace slider or bag adapter if broken or cracked.

9.Mower blades are sharp and can cut. Wrap the blades or wear heavy leather gloves and use CAUTION when handling them.

10.DO NOT test for spark by grounding spark plug next to spark plug hole; spark plug could ignite gas exiting engine.

11.Have machine serviced by an authorized SNAPPER dealer at least once a year and have the dealer install any new safety devices.

12.Use only genuine SNAPPER replacement parts to assure that original standards are maintained.

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Steel Deck Walk Mowers M Model Series Important Safety Instructions Operation Table of Contents Nomenclature IntroductionPRE-START Check List Starting & Operation 2.2.1. Engine & BladePrimer Models Push & Non Commercial Self-Propelled Propelling Mower Handle Height AdjustmentStarting & Operation 2.2.2. Engine & Blade Choke ModelsCommercial OnlyRecycling Operation Cutting Height AdjustmentService After First 5 Hours 3.2.1. Change Engine OIL Check Grease Level in TransmissionOn Next Check Engine Drive Belt Service AnnuallyStorage Procedure Check Mower BladeMower Blade Replacement 4.1.1. Standard Blade Wear Limit Blade SharpeningNinja Blade Wear Limit Wheel Drive Control Adjustment Driven Disc Adjustment Driven Disc ServiceCleaning Drive Disc & Driven Disc Drive Spring Repair/ReplacementReplacing Rubber Driven Disc Ring Replacing Bearing In Driven Disc Assembly Engine Drive Belt Replacement Stretch Type Belts Belt ServicePulley Position Transmission Poly-V Belt ReplacementProblem Probable Cause Corrective Action Troubleshooting100 Service Performed EachClean Sponge Element Engine Manual MAINTENANCE/REPLACEMENT PartsDisclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Page Page Page Steel Deck Walk Behind Mowers M Model Series

MR216015T specifications

The Snapper MR216015T is a versatile and powerful lawn mower designed for residential and commercial use. Renowned for its durability and performance, this model appeals to those seeking efficiency and dependability in lawn maintenance.

One of the standout features of the Snapper MR216015T is its robust 159cc Briggs & Stratton engine, which delivers reliable power for a variety of mowing tasks. This engine is designed for longevity and requires minimal maintenance, making it an appealing choice for those who prioritize ease of use.

The mower incorporates a 21-inch steel cutting deck, which not only ensures a wide cutting swath but also contributes to a professional-looking finish. The deck is engineered for durability and is complemented by a 3-in-1 cutting system, allowing users to choose from side discharge, mulching, or bagging options. This versatility ensures that mowing can be tailored to different lawn types and conditions, making it ideal for various outdoor spaces.

Another key feature of the Snapper MR216015T is its adjustable cutting height system. With six different height settings, users can easily adapt the mower to achieve the desired grass length, enhancing user control and lawn health. This feature is particularly beneficial for those with varying grass types or uneven terrains.

Ergonomics is also a focus in the design of this mower. The handle is adjustable and designed for comfort, allowing operators of different heights to operate the mower without strain. Additionally, the foldable design of the handle facilitates easy storage and transportation, which is an essential consideration for those with limited garage space.

The Snapper MR216015T is equipped with a reliable starting system, which enhances user convenience. Its easy pull-start mechanism ensures that the mower is ready to go when needed, eliminating the frustration of difficult starts often encountered with other models.

Lastly, the Snapper MR216015T has a reputation for being environmentally friendly due to its efficient design that optimizes fuel consumption while minimizing emissions. This makes it a responsible choice for environmentally conscious consumers.

In summary, the Snapper MR216015T lawn mower boasts a powerful engine, a durable cutting deck, adjustable height controls, user-friendly ergonomics, and an efficient starting system, making it a leading choice for anyone looking for reliability and performance in lawn care.
Top Page Image Contents