Snapper MRP216015B important safety instructions Replacing Bearing In Driven Disc Assembly

Page 15

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

4.3.4.Replacing Rubber Driven Disc (Continued from previous page)

2.Using needle nose pliers, unhook the drive spring and slide the driven disc assembly off the hex shaft. See Figure 4.12.

3.Remove the two retaining rings which secure the rubber driven disc to the driven disc assembly. See Figure 4.13.

4.Install new rubber driven disc onto driven disc assembly with retaining rings.

5.Reverse above procedures for reassembly and installation of driven disc assembly.

4.3.5. Replacing Bearing In Driven Disc Assembly

IMPORTANT: The bearing, on these “M” series Non- Commercial machines, is staked into the thrust plate. The bearing will have to be driven out with a mallet and a large punch. A new bearing with four retaining screws will have to be purchased to replace existing bearing.

If the driven disc bearing fails, remove the driven disc assembly and replace bearing as follows:

1.Using a small flat blade screwdriver, free the clip from the transfer rod. Then remove the transfer rod from the clip and the speed control rod. See Figure

2.Using needle nose pliers, unhook the drive spring and slide the driven disc assembly off the hex shaft. See Figure 4.12.

3.Remove both snap rings that secure rubber driven disc hub to thrust plate. See Figure 4.13.

4.Slide the rubber driven disc hub out of the bearing.

5.Drive out existing bearing.

6.Install new bearing and secure to thrust plate with four retaining screws. Tighten screws securely.

7.Reassemble components in reverse order.

DRIVEN DISC

ASSEMBLY

INSTALL NEW

DRIVEN DISC

SNAP

RINGS

FIGURE 4.12

FIGURE 4.13

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Steel Deck Walk Mowers M Model Series Important Safety Instructions Operation Table of Contents Nomenclature IntroductionStarting & Operation 2.2.1. Engine & Blade PRE-START Check ListHandle Height Adjustment Starting & OperationStopping Recycling Operation Cutting Height AdjustmentService After First 5 Hours 3.2.1. Change Engine OIL Check Grease Level in TransmissionOn Next Check Engine Drive Belt Service AnnuallyStorage Procedure Check Mower BladeMower Blade Replacement 4.1.1. Standard Blade Wear Limit Blade SharpeningNinja Blade Wear Limit Wheel Drive Control Adjustment Driven Disc Adjustment Driven Disc ServiceCleaning Drive Disc & Driven Disc Drive Spring Repair/ReplacementReplacing Rubber Driven Disc Ring Replacing Bearing In Driven Disc Assembly Engine Drive Belt Replacement Stretch Type Belts Belt ServicePulley Position Transmission Poly-V Belt ReplacementProblem Probable Cause Corrective Action Troubleshooting100 Service Performed EachClean Sponge Element Engine Manual MAINTENANCE/REPLACEMENT PartsDisclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Page Page Page Steel Deck Walk Behind Mowers M Model Series

MRP216015B specifications

The Snapper MRP216015B is a versatile and efficient lawn mower designed to provide exceptional performance for both residential and commercial gardening needs. As a part of Snapper’s trusted range of outdoor power equipment, the MRP216015B stands out for its innovative features and user-friendly technology.

One of the primary features of the MRP216015B is its robust 159cc OHV engine, which delivers reliable power and performance. This engine ensures that the mower can tackle various types of grass and terrain, making it suitable for a wide range of mowing conditions. The easy start technology allows users to get going quickly without the frustration of a traditional pull-start mechanism.

Another distinguishing characteristic of the Snapper MRP216015B is its 21-inch cutting deck. This size strikes a great balance between maneuverability and coverage, allowing users to cover large areas efficiently while still being able to navigate tight spaces. The steel construction of the deck provides durability, ensuring that the mower can withstand the rigors of regular use.

Additionally, the MRP216015B features a 3-in-1 mowing capability, enabling users to choose between mulching, bagging, or side discharge. This versatility allows for customization based on the specific needs and preferences of the user, whether they want to mulch for added fertilization or bag clippings for a cleaner finish.

The adjustable cutting height feature is another key technology that makes the Snapper MRP216015B stand out. With a simple lever adjustment, users can select from different cutting heights ranging from 1 to 4 inches. This adaptability ensures that the mower can handle different grass types and adapts to seasonal growth patterns effectively.

Comfort and convenience are paramount in the design of the MRP216015B. The ergonomic handle, equipped with cushioning, allows for extended operation without fatigue. Additionally, the foldable handle makes it easy to store the mower in smaller spaces when not in use.

In summary, the Snapper MRP216015B is a powerful, versatile, and user-friendly lawn mower. With its strong engine, durable cutting deck, and adaptable features, the MRP216015B is an excellent choice for anyone looking to achieve a well-manicured lawn efficiently and effectively.
Top Page Image Contents