Snapper NZM19481KWV Cutting Height Adjustment, OPERATION- Motion Controls Driving Machine

Page 12

Section 3 - OPERATING INSTRUCTIONS

3.3CUTTING HEIGHT ADJUSTMENT

1.Adjust cutting height, as desired, to any position, using deck lift lever. The release latch should be pulled up when lowering the deck. When raising the deck, the release latch does not have to be pulled up. IMPORTANT: There is a foot assist pedal located to the right front side of the footrest. Always use this assist pedal to raise or lower the deck to the desired cutting height. See Figure 3.9 & 3.10.

2.If a specific deck height is desired each time the machine is used, insert the stop pin to desired cutting height. See Figure 3.11.

NOTE: The engine does not have to be running to adjust cutting height.

DECK LIFT LEVER

SHOWN IN HIGH

CUTTING HEIGHT

POSITION

PULL RELEASE

LATCH UP WHEN

CHANGING THE

DECK HEIGHT

FIGURE 3.9

DECK LIFT LEVER

SHOWN IN LOW

CUTTING HEIGHT

POSITION

DECK LIFT

ASSIST PEDAL

FIGURE 3.10

WARNING

DO NOT make turns at high speed. Slow machine motion. Move motion control lever gently and with caution. DO NOT make sudden changes in speed or direction.

6 HOLE POSITIONS

FOR STOP PIN

FIGURE 3.11

3.4OPERATION- MOTION CONTROLS

3.4.1.DRIVING MACHINE

1.Start engine. Release parking brake.

2.Move motion control levers gently and with caution in desired direction. See Figure 3.12. FORWARD - Move both control levers forward. REVERSE - Move both control levers rearward. LEFT TURN - Move left control rearward or move right control lever forward.

RIGHT TURN - Move left control forward or move right control lever rearward.

ZERO RADIUS TURN - Move one control lever forward and move the other control lever rearward simultaneously.

REARWARD

MOVEMENT

FORWARD

MOVEMENT

FIGURE 3.12

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents MID Mount Z-RIDER Zero Turning Hydro Drive Series Important Safety Instructions From Previous SnapperMaintenance Table of Contents Introduction NomenclatureSafety Messages and Symbols RUN Operating Instructions PRE-START Check ListStarting & Stopping ENGINE, BLADES, Parking Brake Starting EngineStopping Engine Starting Mower BladesStopping Mower Blades Parking BrakeCutting Height Adjustment OPERATION- Motion Controls Driving MachineStopping Machine Engine Must not Start ifEngine should Start if Engine Must Begin to Stop ifService After First 5 Hours Check Mower BladeAfter Every 25 Operating Hours 4.3.1. Engine Riding Mower Lubrication Before Operating MachineAnnually END of Each Season Deck Removal See Figure Adjustments & Repair Neutral Position AdjustmentsNeutral Position Adjustments From Previous Parking Brake Adjustment Highest cutting position and recheck side to sideTraction Belt Replacement Traction Belt TensionTracking Adjustment Mower Drive Belt Replacement Belt ReplacementBelt Removal Blade Sharpening Battery Battery Removal Battery InstallationBattery Service 1. Remove battery Battery Testing NEW Battery Preparation 1. Remove battery from cartonDo not Overfill Bearing Replacement Insert spindle shaft up through the bottomHydraulic SYSTEM, Purging Problem Probable Cause Trouble Shooting on NextCorrective Action Machine Will Not Move Service Performed Each MAINTENANCE/REPLACEMENT Parts100 Number USE HRS SeasonYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page Page MID Mount Z-RIDER Zero Turning Hydro Drive Series

NZM19481KWV specifications

The Snapper NZM19481KWV is a robust and versatile ride-on lawn mower that offers exceptional performance and efficiency for various residential and commercial landscaping needs. Engineered for precision and durability, this model is a popular choice among lawn care enthusiasts looking to maintain their outdoor space with ease.

One of the standout features of the Snapper NZM19481KWV is its powerful engine. Equipped with a reliable Briggs & Stratton engine, the mower delivers ample power to tackle even the toughest grass conditions. The engine's high torque ensures that the mower can handle hilly terrains and thick grass without compromising performance. Additionally, the engine meets stringent emissions standards, making it an environmentally friendly choice.

The cutting deck on the NZM19481KWV is another highlight. It boasts a 48-inch fabricated cutting deck, which provides a wide cutting path for faster mowing. The deck's design ensures superior airflow, resulting in a finer and more consistent cut. Users can easily adjust the cutting height with a simple lever, allowing for a customized mowing experience suited to various grass types and conditions.

This mower employs innovative technologies that add to its appeal. The AutoShift transmission allows for smooth and effortless gear changes, enabling users to maintain optimal speed regardless of terrain. Coupled with responsive steering, the Snapper NZM19481KWV provides excellent maneuverability, making it ideal for navigating tight spaces and complex landscapes.

Comfort is also a priority with the Snapper NZM19481KWV. The mower features an ergonomic seat with ample cushioning and adjustable armrests, ensuring a comfortable mowing experience even during extended use. The user-friendly controls are intuitively placed, allowing for easy operation without taking your focus off the mowing task at hand.

In terms of maintenance, the Snapper NZM19481KWV is designed for convenience. Its accessible engine and easy-to-remove cutting deck simplify routine tasks, such as oil changes and blade sharpening. The molded fender and deck prevent rust, prolonging the lifespan of the mower.

Overall, the Snapper NZM19481KWV combines performance, technology, and comfort, making it a worthwhile investment for anyone seeking to achieve a pristine lawn. Whether for home use or commercial landscaping, this ride-on mower stands out with its comprehensive features designed to deliver exceptional results.
Top Page Image Contents