Snapper NZM19481KWV important safety instructions Operating Instructions, PRE-START Check List

Page 9

Section 3 - OPERATING INSTRUCTIONS

3.1PRE-START CHECK LIST

Make the following checks and perform the service required before each start-up.

3.1.1.Check tires and add or release air as needed to bring pressure to 12 psi in drive tires. Pressure in front caster wheels should be 25 psi.

3.1.2.Check guards, deflectors and covers to make sure all are in place and securely tightened.

3.1.3.Check engine oil and add oil as needed to bring level up to the FULL mark. Refer to engine owner’s manual for oil specifications. See Figure 3.1.

SAFE LEVEL

AREA

FIGURE 3.1

3.1.4.Check Blade Switch to insure it works freely.

1.Pull the Blade Switch up to the “ON” position to engage or turn “ON” the mower blades.

2.Push Blade Switch down to the “OFF” position to disengage or turn “OFF” the blades.

BLADE SWITCH

FIGURE 3.2

3.1.5.Clean exterior surfaces of cutting deck, engine and pumps of any accumulation of dirt, grass, oil, etc. Keep engine and pump air intake screens and cooling fins clear at all times.

3.1.6.Add fuel to both tanks of the machine outside where fumes can safely dissipate. Make sure both fuel filler caps are tight. Note the fuel tank selector valve. Refer to engine owner’s manual for fuel specifications.

3.1.7.Adjust position of operator’s seat. The seat is mounted on slides. Locate latch lever beneath the seat. Move lever towards the left and slide seat to the desired position. Release latch.

3.1.8.Place mower in desired cutting height setting. Grasp deck lift lever and depress release latch located underneath the lever. Move lever to desired cutting height setting and release latch. Insert stop pin to desired cutting height.

IMPORTANT: There is a foot assist pedal located to the right front side of the footrest. Always use this assist pedal to raise or lower the deck to the desired cutting height. See Figure 3.3.

DECK LIFT

LEVER

RELEASE

LATCH

FOOT

ASSIST PEDAL

INSERT STOP PIN

INTO HOLES FOR

DESIRED CUTTING

HEIGHT

FIGURE 3.3

IMPORTANT: This machine is equipped with hydrostatic drive. The direction of motion and the speed of motion are controlled by the left and right motion control levers. A small movement of these controls can cause the machine to move instantly. DO NOT attempt to operate the machine until you read this manual and become familiar with its operation. Practice with the blades “OFF” disengaged, engine speed at a slow setting and in an open area away from obstacles.

WARNING

DO NOT allow operation of the machine by untrained personnel.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents MID Mount Z-RIDER Zero Turning Hydro Drive Series Important Safety Instructions Snapper From PreviousMaintenance Table of Contents Nomenclature IntroductionSafety Messages and Symbols RUN PRE-START Check List Operating InstructionsStarting Engine Starting & Stopping ENGINE, BLADES, Parking BrakeStarting Mower Blades Stopping EngineStopping Mower Blades Parking BrakeOPERATION- Motion Controls Driving Machine Cutting Height AdjustmentEngine Must not Start if Stopping MachineEngine should Start if Engine Must Begin to Stop ifCheck Mower Blade Service After First 5 HoursAfter Every 25 Operating Hours 4.3.1. Engine Riding Mower Lubrication Before Operating MachineAnnually END of Each Season Deck Removal See Figure Neutral Position Adjustments Adjustments & RepairNeutral Position Adjustments From Previous Highest cutting position and recheck side to side Parking Brake AdjustmentTraction Belt Tension Traction Belt ReplacementTracking Adjustment Mower Drive Belt Replacement Belt ReplacementBelt Removal Blade Sharpening Battery Battery Removal Battery InstallationBattery Service 1. Remove battery Battery Testing NEW Battery Preparation 1. Remove battery from cartonDo not Overfill Insert spindle shaft up through the bottom Bearing ReplacementHydraulic SYSTEM, Purging Problem Probable Cause Trouble Shooting on NextCorrective Action Machine Will Not Move MAINTENANCE/REPLACEMENT Parts Service Performed Each100 Number USE HRS SeasonDisclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page Page MID Mount Z-RIDER Zero Turning Hydro Drive Series

NZM19481KWV specifications

The Snapper NZM19481KWV is a robust and versatile ride-on lawn mower that offers exceptional performance and efficiency for various residential and commercial landscaping needs. Engineered for precision and durability, this model is a popular choice among lawn care enthusiasts looking to maintain their outdoor space with ease.

One of the standout features of the Snapper NZM19481KWV is its powerful engine. Equipped with a reliable Briggs & Stratton engine, the mower delivers ample power to tackle even the toughest grass conditions. The engine's high torque ensures that the mower can handle hilly terrains and thick grass without compromising performance. Additionally, the engine meets stringent emissions standards, making it an environmentally friendly choice.

The cutting deck on the NZM19481KWV is another highlight. It boasts a 48-inch fabricated cutting deck, which provides a wide cutting path for faster mowing. The deck's design ensures superior airflow, resulting in a finer and more consistent cut. Users can easily adjust the cutting height with a simple lever, allowing for a customized mowing experience suited to various grass types and conditions.

This mower employs innovative technologies that add to its appeal. The AutoShift transmission allows for smooth and effortless gear changes, enabling users to maintain optimal speed regardless of terrain. Coupled with responsive steering, the Snapper NZM19481KWV provides excellent maneuverability, making it ideal for navigating tight spaces and complex landscapes.

Comfort is also a priority with the Snapper NZM19481KWV. The mower features an ergonomic seat with ample cushioning and adjustable armrests, ensuring a comfortable mowing experience even during extended use. The user-friendly controls are intuitively placed, allowing for easy operation without taking your focus off the mowing task at hand.

In terms of maintenance, the Snapper NZM19481KWV is designed for convenience. Its accessible engine and easy-to-remove cutting deck simplify routine tasks, such as oil changes and blade sharpening. The molded fender and deck prevent rust, prolonging the lifespan of the mower.

Overall, the Snapper NZM19481KWV combines performance, technology, and comfort, making it a worthwhile investment for anyone seeking to achieve a pristine lawn. Whether for home use or commercial landscaping, this ride-on mower stands out with its comprehensive features designed to deliver exceptional results.
Top Page Image Contents