Snapper NZM19481KWV important safety instructions Maintenance

Page 4

IMPORTANT SAFETY INSTRUCTIONS

OPERATION

(Continued From Previous Page)

8.Keep hands and feet away from rotating blades underneath deck. DO NOT place foot on ground while BLADES are ON or machine is in motion.

9.DO NOT operate machine without entire grass catcher or guards in place. DO NOT point discharge at people, passing cars, windows or doors.

10.Slow down before turning.

11.Watch out for traffic when near or crossing roadways.

12.STOP engine immediately after striking an object or if an abnormal vibration occurs. Remove key. Remove and disconnect the sparkplug wire. Make necessary repairs before resuming operation.

13.Mow only in daylight or with good artificial light.

14.Move motion control levers SLOWLY to maintain control during speed and directional changes.

15.Exercise CAUTION when pulling loads. DO NOT pull loads greater than 300 pounds. Avoid jack knifing. DO NOT turn sharply. Attach loads to approved hitch point only following manufacturer’s instructions.

16.On slopes, the weight of towed equipment may cause loss of traction and loss of control. When towing travel slowly and allow extra distance to stop.

17.DO NOT operate engine in enclosed areas. Engine exhaust gases contain carbon monoxide, an odorless and deadly poison.

MAINTENANCE

1.DO NOT store machine or fuel container inside where fumes may reach an open flame, spark or pilot light such as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of the reach of children in a well ventilated, unoccupied building. Shut off fuel (when equipped with valve) while storing or transporting machine.

2.Clean grass and debris from engine, mufflers, drives and cutting units to help prevent overheating and fires. Clean up fuel, oil and excess grease.

3.When draining fuel tank, drain fuel into an approved container outdoors and away from open flame.

4.Check brakes frequently; adjust, repair or replace as needed.

5.Keep all bolts, nuts and screws properly tight. Check that all cotter pins are in proper position.

MAINTENANCE

(Continued From Previous Column)

6.Always provide adequate ventilation when running engine. Engine exhaust gases contain carbon monoxide, an odorless and deadly poison.

7.Disconnect battery before performing maintenance or service. Cranking engine could cause injury. Disconnect negative (black) cable from battery first and positive (red) cable last. Reconnect positive first and negative last. Charge battery in an open, well ventilated area away from spark and flames. Unplug charger before connecting or disconnecting from battery. Wear protective clothing and insulated gloves.

8.Park machine on level ground. DO NOT work under machine without safety blocks.

9.Service engine and clean, adjust or repair only when engine and blades are stopped. Remove spark plug wire(s) from spark plug(s) and secure wire(s) away from spark plug(s).

10.DO NOT change engine governor speed settings or overspeed engine. DO NOT make adjustments with the engine running.

11.Lubricate machine at intervals specified in manual to prevent controls from binding.

12.Mower blades are sharp and can cut. Wrap the blades or wear heavy leather gloves and use CAUTION when handling them. Never straighten or weld blades, only replace them.

13.DO NOT test for spark by grounding spark plug next to spark plug hole; spark plug could ignite gas exiting engine.

14.Carefully release pressure from components with stored energy.

15.Have machine serviced by an authorized SNAPPER dealer at least once a year and have the dealer install any new safety devices. Never allow untrained personnel to service machine.

16.Use only genuine SNAPPER replacement parts to assure that original standards are maintained.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents MID Mount Z-RIDER Zero Turning Hydro Drive Series Important Safety Instructions From Previous SnapperMaintenance Table of Contents Introduction NomenclatureSafety Messages and Symbols RUN Operating Instructions PRE-START Check ListStarting & Stopping ENGINE, BLADES, Parking Brake Starting EngineStopping Engine Starting Mower BladesStopping Mower Blades Parking BrakeCutting Height Adjustment OPERATION- Motion Controls Driving MachineStopping Machine Engine Must not Start ifEngine should Start if Engine Must Begin to Stop ifService After First 5 Hours Check Mower BladeAfter Every 25 Operating Hours 4.3.1. Engine Before Operating Machine Riding Mower LubricationAnnually END of Each Season Deck Removal See Figure Adjustments & Repair Neutral Position AdjustmentsNeutral Position Adjustments From Previous Parking Brake Adjustment Highest cutting position and recheck side to sideTraction Belt Replacement Traction Belt TensionBelt Replacement Tracking Adjustment Mower Drive Belt ReplacementBelt Removal Blade Sharpening Battery Installation Battery Battery RemovalBattery Service 1. Remove battery NEW Battery Preparation 1. Remove battery from carton Battery TestingDo not Overfill Bearing Replacement Insert spindle shaft up through the bottomHydraulic SYSTEM, Purging Trouble Shooting on Next Problem Probable CauseCorrective Action Machine Will Not Move Service Performed Each MAINTENANCE/REPLACEMENT Parts100 Number USE HRS SeasonYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page Page MID Mount Z-RIDER Zero Turning Hydro Drive Series

NZM19481KWV specifications

The Snapper NZM19481KWV is a robust and versatile ride-on lawn mower that offers exceptional performance and efficiency for various residential and commercial landscaping needs. Engineered for precision and durability, this model is a popular choice among lawn care enthusiasts looking to maintain their outdoor space with ease.

One of the standout features of the Snapper NZM19481KWV is its powerful engine. Equipped with a reliable Briggs & Stratton engine, the mower delivers ample power to tackle even the toughest grass conditions. The engine's high torque ensures that the mower can handle hilly terrains and thick grass without compromising performance. Additionally, the engine meets stringent emissions standards, making it an environmentally friendly choice.

The cutting deck on the NZM19481KWV is another highlight. It boasts a 48-inch fabricated cutting deck, which provides a wide cutting path for faster mowing. The deck's design ensures superior airflow, resulting in a finer and more consistent cut. Users can easily adjust the cutting height with a simple lever, allowing for a customized mowing experience suited to various grass types and conditions.

This mower employs innovative technologies that add to its appeal. The AutoShift transmission allows for smooth and effortless gear changes, enabling users to maintain optimal speed regardless of terrain. Coupled with responsive steering, the Snapper NZM19481KWV provides excellent maneuverability, making it ideal for navigating tight spaces and complex landscapes.

Comfort is also a priority with the Snapper NZM19481KWV. The mower features an ergonomic seat with ample cushioning and adjustable armrests, ensuring a comfortable mowing experience even during extended use. The user-friendly controls are intuitively placed, allowing for easy operation without taking your focus off the mowing task at hand.

In terms of maintenance, the Snapper NZM19481KWV is designed for convenience. Its accessible engine and easy-to-remove cutting deck simplify routine tasks, such as oil changes and blade sharpening. The molded fender and deck prevent rust, prolonging the lifespan of the mower.

Overall, the Snapper NZM19481KWV combines performance, technology, and comfort, making it a worthwhile investment for anyone seeking to achieve a pristine lawn. Whether for home use or commercial landscaping, this ride-on mower stands out with its comprehensive features designed to deliver exceptional results.
Top Page Image Contents