Snapper 1807-1 owner manual Add Engine Oil and Fuel, Connect Hose and Water Supply to Pump

Page 7

Snapper 2300 PSI Pressure Washer

4.Insert other “L” hook through hole just above billboard on right side of handle (viewing from rear of unit). Hold hook in place with pliers and attach locknut with 7/16” wrench (Figure 3).

Add Engine Oil and Fuel

• Place pressure washer on a level surface.

CAUTION

Any attempt to crank or start the engine before it has been properly filled with the recommended oil will result in equipment failure.

•Refer to engine manual for oil and fuel fill information.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

•Refer to engine owner’s manual and follow oil and fuel recommendations and instructions.

NOTE: Check oil often during engine break–in. Refer to engine owner’s manual for recommendations.

3.Before connecting garden hose to water inlet, inspect inlet screen (Figure 6). Clean screen if it contains debris or have it replaced if damaged. DO NOT RUN PRESSURE WASHER IF SCREEN IS DAMAGED.

Figure 6 — Connect the Garden Hose to Water Inlet

Inspect inlet

screen, DO NOT use if damaged;

clean if dirty.

4.Run water through garden hose for 30 seconds to clean out any debris.Turn off water.

IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 100°F).

5.Connect garden hose (not to exceed 50 feet in length) to water inlet.Tighten by hand (Figure 6).

Connect Hose and Water Supply to Pump

IMPORTANT: To avoid pump damage, you must assemble the nozzle extension to the spray gun and attach all hoses before you start the engine.

1.Uncoil high pressure hose and attach one end of hose to base of spray gun (Figure 4).Tighten by hand.

Figure 4 — Connect High Pressure Hose to Spray Gun

Connect high pressure hose here

2.Attach other end of high pressure hose to high pressure outlet on pump (Figure 5).Tighten by hand.

Figure 5 — Connect High Pressure Hose to Pump

CAUTION

There MUST be at least ten feet of unrestricted garden hose between the pressure washer inlet and any flow shut off device, such as a ‘Y’ shut-off connector or other convenience-type water shut-off valve.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

6.Turn ON water and squeeze trigger on spray gun to purge pump system of air and impurities.

WARNING

High pressure spray can cause paint chips or other particles to become airborne.

•Always wear eye protection when using this equipment or in vicinity of where equipment is in use.

•Before starting the pressure washer, be sure you are wearing adequate eye protection.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 2300PSI Safety Rules Table of ContentsEquipment Description When Transporting or Repairing Equipment Unintentional sparking can result in fire or electric shock Fire or severe burns can occurKnow Your Pressure Washer Remove Pressure Washer from Carton AssemblyCarton Contents Preparing Pressure Washer for USEConnect Hose and Water Supply to Pump Add Engine Oil and FuelHow to Stop Your Pressure Washer HOW to USE Your Pressure WasherChecklist Before Starting Engine How to Start Your Pressure WasherTo apply detergent, follow these steps How to Use Adjustable NozzleApplying Detergent with the Adjustable Nozzle You must attach all hoses before you start the engineDischarging the warm water onto the ground Pressure Washer RinsingAutomatic Cool Down System For RinsingGeneral Maintenance Recommendations SpecificationsPressure Washer Maintenance To remove contaminants from the pump, follow these steps Cleaning Detergent Siphoning TubeNozzle Maintenance Check In-Line FilterChanging Pump Oil Engine MaintenanceRing Maintenance Pump MaintenanceProtecting the Pump You must protect your unit from freezing temperaturesPreparing the Unit for Storage Storing the EngineSnapper 2300 PSI Pressure Washer Snapper 2300 PSI Pressure Washer Troubleshooting Description Exploded View and Parts List Main UnitItems Not Illustrated Description Include all parts shown within the box Exploded View and Parts List PumpAbout your equipment warranty Snapper Owner Warranty Policy Effective January 1Equipment Consumer Use Commercial Use

1807-1 specifications

The Snapper 1807-1 is a sophisticated piece of equipment that caters primarily to landscaping and lawn care enthusiasts and professionals. This versatile machine combines power and efficiency, making it an essential tool for maintaining large areas of turf. Its design and functionality offer robust features that stand out in the current market.

One of the key features of the Snapper 1807-1 is its reliable engine. Powered by a 180 cc OHV engine, this mower is designed for optimal performance, ensuring durability and long-lasting use. The engine not only provides ample power but also enhances fuel efficiency, allowing users to cover larger areas without the need for frequent refueling. The self-propelling mechanism further complements this power by reducing the physical strain on the operator, making it easier to navigate various terrains.

The cutting deck of the Snapper 1807-1 is another highlight. With a 21-inch width, it is perfect for maneuvering through tight spaces while still delivering a professional finish. The deck is designed for superior grass clipping collection, helping maintain a neat and tidy lawn. Additionally, the adjustable height settings allow users to customize the cutting height based on their specific lawn care needs, making it suitable for different grass types and preferences.

The Snapper 1807-1 also incorporates advanced technologies that enhance its usability. The lawn mower features a robust gear drive system, which offers smoother operation and increased control over speed settings. This means that whether you are tackling tall grass or mowing a manicured lawn, you can adjust the speed to your liking, ensuring a seamless mowing experience.

Moreover, the ergonomic design of the controls provides ease of use, allowing operators to engage and adjust functions intuitively even while on the move. The foldable handle enhances storage capabilities, making it space-saving for users with limited storage options.

Finally, maintenance is simplified in the Snapper 1807-1. The machine comes equipped with easily accessible components, allowing for quick checks and servicing. This attention to maintenance needs ensures that the mower remains in top condition, extending its lifespan and reliability. Overall, the Snapper 1807-1 is a powerful, user-friendly machine that meets the demands of both amateur and professional landscapers alike. Its thoughtful design and innovative features make it a standout choice in the lawn care equipment market.
Top Page Image Contents