Snapper 1807-1 owner manual HOW to USE Your Pressure Washer, Checklist Before Starting Engine

Page 8

Snapper 2300 PSI Pressure Washer

Checklist Before Starting Engine

Review the unit’s assembly to confirm you have performed all of the following:

1.Make sure handle is in place and secure.

2.Check that oil has been added to proper level in engine crankcase.

3.Add proper fuel to fuel tank.

4.Check for properly attached hose connections.

5.Check to make sure there are no kinks, cuts, or damage to high pressure hose.

6.Provide a proper water supply at an adequate flow.

7.Be sure to read “Safety Rules” and “How To Use Your Pressure Washer” before using pressure washer.

6.Attach nozzle extension to spray gun (Figure 7). Tighten by hand.

Figure 7 — Connect Nozzle Extension to Spray Gun

7.Position nozzle in low pressure mode (slide nozzle forward) and squeeze trigger on spray gun to relieve pressure caused by turning ON water.Water will flow out of gun in a thin stream. Continue to hold trigger until there is a steady stream of water and no air remains in system. Release trigger.

8.Engage safety latch to spray gun trigger (Figure 8).

HOW TO USE YOUR PRESSURE WASHER

If you have any problems operating your pressure washer, please call the pressure washer helpline at 1-800-317-7833.

How to Start Your Pressure Washer

To start your pressure washer for the first time, follow these instructions step-by-step.This starting information also applies if you have let the pressure washer sit idle for at least a day.

1.Place pressure washer near an outside water source capable of supplying water at a flow rate greater than 3.0 gallons per minute and no less than 20 PSI at pressure washer end of garden hose.

2.Check that high pressure hose is connected to spray gun and pump. See “Preparing Pressure Washer for Use” for illustrations.

Figure 8 — Spray Gun with Safety Latch Engaged

Safety Latch

9.Start engine according to instructions given in engine owner’s manual.

NOTE: If the recoil starter is hard to pull, it may be necessary to squeeze the gun trigger to relieve internal pump pressure.

CAUTION

Avoid injury from kickback.

•Squeeze trigger on spray gun each time recoil starter is pulled and engine fails to start.

3.Make sure unit is in a level position.

4.Connect garden hose to water inlet on pressure washer pump. Turn ON the water.

5.Squeeze trigger on gun until you have a steady stream of water.This purges the pump of air and impurities.

CAUTION

DO NOT run the pump without the water supply connected and turned on.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

How to Stop Your Pressure Washer

•Let the engine idle for two minutes.

•Turn engine off according to instructions given in the engine owner’s manual.

•Squeeze trigger on the spray gun to relieve pressure in the hose.

NOTE: A small amount of water will squirt out when you release the pressure.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents 2300PSI Equipment Description Table of ContentsSafety Rules When Transporting or Repairing Equipment Fire or severe burns can occur Unintentional sparking can result in fire or electric shockKnow Your Pressure Washer Assembly Carton ContentsPreparing Pressure Washer for USE Remove Pressure Washer from CartonAdd Engine Oil and Fuel Connect Hose and Water Supply to PumpHOW to USE Your Pressure Washer Checklist Before Starting EngineHow to Start Your Pressure Washer How to Stop Your Pressure WasherHow to Use Adjustable Nozzle Applying Detergent with the Adjustable NozzleYou must attach all hoses before you start the engine To apply detergent, follow these stepsPressure Washer Rinsing Automatic Cool Down SystemFor Rinsing Discharging the warm water onto the groundPressure Washer Maintenance SpecificationsGeneral Maintenance Recommendations Cleaning Detergent Siphoning Tube Nozzle MaintenanceCheck In-Line Filter To remove contaminants from the pump, follow these stepsEngine Maintenance Ring MaintenancePump Maintenance Changing Pump OilYou must protect your unit from freezing temperatures Preparing the Unit for StorageStoring the Engine Protecting the PumpSnapper 2300 PSI Pressure Washer Snapper 2300 PSI Pressure Washer Troubleshooting Items Not Illustrated Description Exploded View and Parts List Main UnitDescription Exploded View and Parts List Pump Include all parts shown within the boxEquipment Consumer Use Commercial Use Snapper Owner Warranty Policy Effective January 1About your equipment warranty

1807-1 specifications

The Snapper 1807-1 is a sophisticated piece of equipment that caters primarily to landscaping and lawn care enthusiasts and professionals. This versatile machine combines power and efficiency, making it an essential tool for maintaining large areas of turf. Its design and functionality offer robust features that stand out in the current market.

One of the key features of the Snapper 1807-1 is its reliable engine. Powered by a 180 cc OHV engine, this mower is designed for optimal performance, ensuring durability and long-lasting use. The engine not only provides ample power but also enhances fuel efficiency, allowing users to cover larger areas without the need for frequent refueling. The self-propelling mechanism further complements this power by reducing the physical strain on the operator, making it easier to navigate various terrains.

The cutting deck of the Snapper 1807-1 is another highlight. With a 21-inch width, it is perfect for maneuvering through tight spaces while still delivering a professional finish. The deck is designed for superior grass clipping collection, helping maintain a neat and tidy lawn. Additionally, the adjustable height settings allow users to customize the cutting height based on their specific lawn care needs, making it suitable for different grass types and preferences.

The Snapper 1807-1 also incorporates advanced technologies that enhance its usability. The lawn mower features a robust gear drive system, which offers smoother operation and increased control over speed settings. This means that whether you are tackling tall grass or mowing a manicured lawn, you can adjust the speed to your liking, ensuring a seamless mowing experience.

Moreover, the ergonomic design of the controls provides ease of use, allowing operators to engage and adjust functions intuitively even while on the move. The foldable handle enhances storage capabilities, making it space-saving for users with limited storage options.

Finally, maintenance is simplified in the Snapper 1807-1. The machine comes equipped with easily accessible components, allowing for quick checks and servicing. This attention to maintenance needs ensures that the mower remains in top condition, extending its lifespan and reliability. Overall, the Snapper 1807-1 is a powerful, user-friendly machine that meets the demands of both amateur and professional landscapers alike. Its thoughtful design and innovative features make it a standout choice in the lawn care equipment market.
Top Page Image Contents