Cub Cadet 48-inch Fabricated Deck service manual Figure Fuel Shutoff Valve

Page 10

Steering Levers

Deck Lift Handle

Brake

Figure. 3

4.Electric Blade Clutch Switch: (See Figure 1.) Located on the right side of the mower beside the ignition switch. This is an “on/off” push pull switch that controls the electric blade clutch which supplies power to the cut- ting blades through the PTO. The switch must be turned off to start the engine and should be turned off for safety any time another per- son approaches the mower or the mowing deck is raised to the transport position. Power to the electric clutch will also be cut off if the operator leaves the operator’s seat.

5.Parking Brake: (See Figure 3.) Located on the left side of the traction unit. The handle is an overcenter lever which applies the drum- type brake on each drive wheel when the han- dle is pulled to the rear. The brake must be engaged in order to start the engine.

6.Deck Lift Handle and Foot Pedal Lift Assist: (See Figure 3.) Located on the right front corner of the mowing deck. Raise the mowing deck to the transport position, by pull- ing the lever to the rear and moving it inward into the stop for transport. To lower the mow- ing deck, pull the deck lift handle and move it outward. This lower’s the deck to the cutting position.The foot pedal lift assist (not pictured above) can provide “lift assist” to the hand lever or with “foot effort only”. To provide assistance to the lift handle: remove the detent pin from the pedal assembly. Fold the pedal down to the horizontal position so the hole in the pedal aligns with the hole in the lever. Re-install the detent pin. Pull on the Lift handle and depress the foot pedal to raise the deck. Lifting with “foot effort only” depress the foot pedal (the hand lever will lock into trans- port position if fully depressed). To release the lift mechanism depress the foot pedal, move the hand lever outward and slowly reduce foot pedal effort to lower the mechanism. To ser- vice the unit: Remove the detent pin from the

Note: The 19hp and 23hp use the 5 gallon fuel tank.

Figure. 4 Fuel Shutoff Valve

pedal assembly. Fold the pedal up to vertical position so the hole in the pedal aligns with the hole in the lever. Reinstall the detent pin. This is the required position for the foot pedal for the foot platform to tilt forward and to access some of the machines components.

7.Fuel Shutoff Valve: (See Figure 4.) Located on top of the fuel tank(s). When turned in a clockwise direction until it stops, it will shut off the flow of fuel to the engine. When turned in a counterclockwise direction it will open and allow fuel to flow to the engine. Close this valve if you are not going to run the mower for a period of 30 minutes or more to prevent flooding the engine.

8.Seat Adjustment Lever: The Seat Adjust- ment Lever is located beneath the seat. The Seat Adjustment Lever is used to move the seat forward and backward. To place the seat in the desired position pull the seat adjust- ment lever to the left then push the seat for- ward or back to the desired position. Release the lever so the seat will lock in place.

9.Digital Tachometer and Hour Meter: (See Figure 1) Located on the right side of the mower in front of the ignition switch. When the machine is running the tachometer displays engine rpm. When the machine is off the tachometer displays running time.

10.Choke Lever: (See Figure 2) The Choke Lever is located on the left instrument panel next to the seat. The Choke Lever is operated manually. Having the Choke Lever in the ON position helps the engine to start during initial start-up. During normal operation the Choke Lever should be in the OFF position.

Note: The Tanks equipped with E.F.I. do not have a choke control.

Note: There will be a flashing “LUBE” for each recommended lubrication interval. There is a flashing “OIL” at each recommended engine oil and filter change.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Hydrostatic Zero-Turn Commercial Riding Mower Table of Contents Forward Models Listed in this ManualSafety Precautions General Safety OperationsGeneral When Mowing Related to FuelSafety Decals and Labels Shield Missing do not OperateSpecifications Safety Awareness when Mowing When MowingOperating Instructions To Mow Grass and Produce a Striped Pat- tern Figure Fuel Shutoff Valve Initial Adjustments Check the fluid levels and tiresOrientation Zero Turn Break-In And Operating ProceduresLubricate all fittings listed in the mainte- nance section Initial OperationStart the Engine Parking the Mower Maintenance ServiceMower Deck Removing the Mower DeckChanging a Blade Changing the Blade Drive BeltsHydraulic Oil Changing the Spindle AssemblyStop the engine and remove the key from the ignition switch Adding Hydraulic Oil use SAE20WElectrical Circuit Battery RemovalInstalling the Battery Specific Gravity Freezing Temp FPage Tires Inflation PressureHydraulic System BrakesHydraulic Oil Tank and Filter Storage Maintenance Schedule OIL Chart If Mower is so equippedHigh Speed Tracking Adjustment Enginge RPM Check and AdjustmentDeck Center Anti-Scalp Roller Settings Deck Corner Ball Wheel Roller SettingsLap Bar Adjustment Deck leveling Procedure Wiring Diagram MANUFACTURER’S Limited Warranty Turf Equipment

48-inch Fabricated Deck specifications

The Cub Cadet 48-inch Fabricated Deck is a top-quality mowing solution designed for both residential and commercial users seeking durability and performance. This innovative mower deck stands out for its robust construction and versatile capabilities, providing an ideal balance for those who prioritize both efficiency and performance in their lawn care routine.

One of the standout features of the Cub Cadet 48-inch Fabricated Deck is its heavy-duty, 11-gauge steel construction. This not only enhances the deck's durability but also ensures that it can withstand the rigors of frequent use in various mowing conditions. The fabricated design contributes to a more solid and resilient structure compared to stamped decks, which often compromise performance over time.

Another key characteristic of this deck is its superior cutting performance. The 48-inch cutting width allows for efficient mowing in larger areas while enabling the user to navigate around obstacles with ease. The design incorporates precision-engineered blades, which facilitate a clean and uniform cut. The high-lift blades are particularly beneficial for discharging grass clippings effectively, ensuring a well-manicured appearance on any lawn.

The deck also features adjustable cutting heights, ranging anywhere from 1.5 inches to 4 inches, allowing users to customize their mowing experience based on the specific needs of their grass type and the current season. This adaptability ensures optimal results all year round.

Further enhancing the mowing experience, the Cub Cadet 48-inch Fabricated Deck integrates technologies that contribute to ease of use. The deck’s design allows for seamless attachment and detachment, making it easy to switch between mowing and other tasks. Additionally, the deck includes a maintenance-free spindle system, which reduces the need for regular upkeep and extends the overall life span of the mower.

The versatility of the deck also makes it compatible with several Cub Cadet riding mowers and lawn tractors, expanding its usability for a wide range of customers. Whether for tackling large yards or managing commercial properties, the Cub Cadet 48-inch Fabricated Deck proves to be an exceptional tool that combines strength, efficiency, and user-friendly features. Overall, this fabricated deck is an investment in quality lawn care, guaranteed to deliver outstanding performance and satisfaction for years to come.
Top Page Image Contents