Cub Cadet 48-inch Fabricated Deck service manual Changing a Blade, Changing the Blade Drive Belts

Page 15

Linch Pins

Linch Pins

Figure. 6

d.Detach the mower drive belt.

e.Remove six linchpins (See Fig. 6) (4) from the deck and (2) from the front of the mower. Remove the linchpins on the left and right rear side of the cutter deck (2); remove the linchpins on the left and right front side of the cutter deck (2); and remove the linchpins on the front of the mower (2).

f.Turn front caster wheels outward.

g.Shift the deck toward the operator’s left side of the mower and remove.

h.To install reverse the process.

2.Changing a Blade:

a.Remove the Key from the ignition and dis- connect the spark plug.

b.Jack up the front of the mowing deck about one foot and block it in that position.

c.Wrap a rag around one end of the blade and grasp it to prevent it from turning, or secure the blade by placing a block of wood between the blade and the deck housing.

d.Use a 1-1/8" socket wrench on the pulley side of the spindle to secure.

e.Remove the hex nut using a 1-1/8" wrench.

f.Remove the hex nut.

g.To replace the blade reverse the above process and tighten nut to 100-120 lb ft.

WARNING:

Never mow with dull blades! Blades that are bent should be replaced! The cutting blades are sharp and can cause severe injury. Wrap the cutting surface of the blade with a rag to avoid injury.

Height of Cut Clevis Pin

a.Set the parking brake.

b.Clean any debris from the blades. Keep blades sharp and free of build up at all times.

c.Sharpen blades evenly at the original 30° angle to maintain balanced cutting blades. Do not sharpen the underside of the blades. Use a electric blade sharpener, a conventional electric grinder or a hand file to sharpen the blades.

d.Replace any blade with severe nicks or dents that cannot be removed by filing.

e.Check the balance of the blade after sharpening by placing it on a blade bal- ancer. Do not use un-balanced blades.

f.If the blade dips on one end, file stock off of the cutting surface on that end.

Note: Blades that cannot be easily bal- anced—REPLACE.

3.Changing the Blade Drive Belts:

a.Set the parking brake. Remove ignition key and both spark plug caps.

b.Unscrew the wing nuts from the deck cov- ers and remove both covers.

c.Using a 1/2" socket breaker bar or socket rachet insert the male end into the 1/2" opening in the lower idler arm assembly and pull the idler arm clockwise. While holding the idler arm back, loosen the blade drive belt from the pulley and slide the belt away from the pulley.

d.Remove tension of the PTO belt by moving the belt tensioning rod. Loosen the belt retaining bolt.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Hydrostatic Zero-Turn Commercial Riding Mower Table of Contents Models Listed in this Manual ForwardGeneral Safety Operations Safety PrecautionsGeneral Related to Fuel When MowingShield Missing do not Operate Safety Decals and LabelsSpecifications When Mowing Safety Awareness when MowingOperating Instructions To Mow Grass and Produce a Striped Pat- tern Figure Fuel Shutoff Valve Check the fluid levels and tires Initial AdjustmentsInitial Operation Zero Turn Break-In And Operating ProceduresLubricate all fittings listed in the mainte- nance section OrientationStart the Engine Removing the Mower Deck Maintenance ServiceMower Deck Parking the MowerChanging the Blade Drive Belts Changing a BladeAdding Hydraulic Oil use SAE20W Changing the Spindle AssemblyStop the engine and remove the key from the ignition switch Hydraulic OilSpecific Gravity Freezing Temp F Battery RemovalInstalling the Battery Electrical CircuitPage Inflation Pressure TiresBrakes Hydraulic SystemHydraulic Oil Tank and Filter Storage Maintenance Schedule If Mower is so equipped OIL ChartEnginge RPM Check and Adjustment High Speed Tracking AdjustmentDeck Corner Ball Wheel Roller Settings Deck Center Anti-Scalp Roller SettingsLap Bar Adjustment Deck leveling Procedure Wiring Diagram MANUFACTURER’S Limited Warranty Turf Equipment

48-inch Fabricated Deck specifications

The Cub Cadet 48-inch Fabricated Deck is a top-quality mowing solution designed for both residential and commercial users seeking durability and performance. This innovative mower deck stands out for its robust construction and versatile capabilities, providing an ideal balance for those who prioritize both efficiency and performance in their lawn care routine.

One of the standout features of the Cub Cadet 48-inch Fabricated Deck is its heavy-duty, 11-gauge steel construction. This not only enhances the deck's durability but also ensures that it can withstand the rigors of frequent use in various mowing conditions. The fabricated design contributes to a more solid and resilient structure compared to stamped decks, which often compromise performance over time.

Another key characteristic of this deck is its superior cutting performance. The 48-inch cutting width allows for efficient mowing in larger areas while enabling the user to navigate around obstacles with ease. The design incorporates precision-engineered blades, which facilitate a clean and uniform cut. The high-lift blades are particularly beneficial for discharging grass clippings effectively, ensuring a well-manicured appearance on any lawn.

The deck also features adjustable cutting heights, ranging anywhere from 1.5 inches to 4 inches, allowing users to customize their mowing experience based on the specific needs of their grass type and the current season. This adaptability ensures optimal results all year round.

Further enhancing the mowing experience, the Cub Cadet 48-inch Fabricated Deck integrates technologies that contribute to ease of use. The deck’s design allows for seamless attachment and detachment, making it easy to switch between mowing and other tasks. Additionally, the deck includes a maintenance-free spindle system, which reduces the need for regular upkeep and extends the overall life span of the mower.

The versatility of the deck also makes it compatible with several Cub Cadet riding mowers and lawn tractors, expanding its usability for a wide range of customers. Whether for tackling large yards or managing commercial properties, the Cub Cadet 48-inch Fabricated Deck proves to be an exceptional tool that combines strength, efficiency, and user-friendly features. Overall, this fabricated deck is an investment in quality lawn care, guaranteed to deliver outstanding performance and satisfaction for years to come.
Top Page Image Contents