Cub Cadet 48-inch Fabricated Deck service manual High Speed Tracking Adjustment

Page 24

Performance Adjustments

A. High Speed Tracking Adjustment

If mower tracks to one side with both lap bars in fully forward position:

1.Check air pressure in all four tires:

a.Pressure should be within specified ranges and balanced side-to-side.

b.Rear tires 8-10 psi. recommended (20 psi MAX.)

c.Front tires 20-25 psi. recommended (28 psi MAX.

2.Check hydraulic fluid level (Ref. Engine owner’s manual)

3.Verify that the mower does not creep when the engine is running, the lap bars are in the neutral position and the parking brake is released. (Refer to section D-3 on page 19 of this manual if this condition exists).

4.Recheck the tracking after any adjustments based on the above.

5.If uneven tracking persists, adjust as follows. (see Fig. 10)

a.Unit tracks to the RIGHT, adjust Left lap bar stop bolt to make it longer.

b.Unit tracks to the LEFT, adjust Right lap bar stop bolt to make it longer.

6.Re-check the tracking and make any fine tun- ing adjustments to the lap bar stop bolts as required.

Note: If stop bolt is adjusted too far, track-

ing problem will change sides. Make the fine tuning adjustments by shortening the same bolt.

Figure. 10

Lap Bar Stop Bolt

B. Enginge RPM Check and Adjustment

Description

High RPM Spec.

Low RPM Spec.

 

 

 

 

 

 

19, 23, & 25 Hp Kawasaki

3600 +/-50

1550 +/-100

 

 

 

20 & 24 HP Honda

3600 +/-50

1550 +/-100

 

 

 

25 & 27 HP Kohler

3600 +/-50

1550 +/-100

 

 

 

28HP Kohler E.F.I.

3600 +/-50

1550 +/-100

 

 

 

28 & 33 HP Generac

3600 +/-50

1550 +/-100

 

 

 

NOTE: RPM Specs. are for free running engines under no load.

1.Verify that the lap bars are in the neutral posi- tion, the parking brake is on, and the PTO drive is disengaged.

2.Start the mower and let it run at approximately half throttle for 3-5 minutes to bring the engine up to operating temperature.

3.Locate the Hour Meter/Tachometer/ Service Minder display on the right hand operator con- trol panel. (see Fig.1 on page 8 of the manual) This display defaults to Tachometer mode when engine is running.

4.Move the throttle lever to the high speed posi- tion and note the RPM reading on the display.

5.Move the throttle lever back to the low speed position and again note the displayed RPM’s.

6.Compare these noted RPM readings to the specifications in Table 1, for the engine that is on your mower.

7.If the readings do not correspond to the ranges in the table, refer to the engine owner’s manual for the proper adjustment procedures.

8.If adjustments per the engine operator’s man- ual do not result in proper RPM readings, con- tact your service technician.

9.Note: The throttle cable sheath may shrink or slip over time, changing the relationship between the throttle lever on the left hand operator control panel and the throttle arm on the engine. To readjust the throttle cable:

a.Make sure the engine is off, place lap bars in the neutral position, set the parking brake, and disconnect and ground both of the spark plug wires.

b.Locate and loosen the cable clamp on the engine throttle plate.

c.Place the operator’s throttle lever to the high speed position and then slide the cable through the clamp until the throttle arm is in the full throttle position. (Ref. Engine owner’s manual)

d.Tighten the cable clamp.

e.Move the operator’s throttle lever between high and low speed and verify that the engine throttle arm also moves through it’s full range of motion.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Hydrostatic Zero-Turn Commercial Riding Mower Table of Contents Forward Models Listed in this ManualGeneral Safety Operations Safety PrecautionsGeneral When Mowing Related to FuelSafety Decals and Labels Shield Missing do not OperateSpecifications When Mowing Safety Awareness when MowingOperating Instructions To Mow Grass and Produce a Striped Pat- tern Figure Fuel Shutoff Valve Initial Adjustments Check the fluid levels and tiresZero Turn Break-In And Operating Procedures Lubricate all fittings listed in the mainte- nance sectionOrientation Initial OperationStart the Engine Maintenance Service Mower DeckParking the Mower Removing the Mower DeckChanging a Blade Changing the Blade Drive BeltsChanging the Spindle Assembly Stop the engine and remove the key from the ignition switchHydraulic Oil Adding Hydraulic Oil use SAE20WBattery Removal Installing the BatteryElectrical Circuit Specific Gravity Freezing Temp FPage Tires Inflation PressureBrakes Hydraulic SystemHydraulic Oil Tank and Filter Storage Maintenance Schedule OIL Chart If Mower is so equippedHigh Speed Tracking Adjustment Enginge RPM Check and AdjustmentDeck Corner Ball Wheel Roller Settings Deck Center Anti-Scalp Roller SettingsLap Bar Adjustment Deck leveling Procedure Wiring Diagram MANUFACTURER’S Limited Warranty Turf Equipment

48-inch Fabricated Deck specifications

The Cub Cadet 48-inch Fabricated Deck is a top-quality mowing solution designed for both residential and commercial users seeking durability and performance. This innovative mower deck stands out for its robust construction and versatile capabilities, providing an ideal balance for those who prioritize both efficiency and performance in their lawn care routine.

One of the standout features of the Cub Cadet 48-inch Fabricated Deck is its heavy-duty, 11-gauge steel construction. This not only enhances the deck's durability but also ensures that it can withstand the rigors of frequent use in various mowing conditions. The fabricated design contributes to a more solid and resilient structure compared to stamped decks, which often compromise performance over time.

Another key characteristic of this deck is its superior cutting performance. The 48-inch cutting width allows for efficient mowing in larger areas while enabling the user to navigate around obstacles with ease. The design incorporates precision-engineered blades, which facilitate a clean and uniform cut. The high-lift blades are particularly beneficial for discharging grass clippings effectively, ensuring a well-manicured appearance on any lawn.

The deck also features adjustable cutting heights, ranging anywhere from 1.5 inches to 4 inches, allowing users to customize their mowing experience based on the specific needs of their grass type and the current season. This adaptability ensures optimal results all year round.

Further enhancing the mowing experience, the Cub Cadet 48-inch Fabricated Deck integrates technologies that contribute to ease of use. The deck’s design allows for seamless attachment and detachment, making it easy to switch between mowing and other tasks. Additionally, the deck includes a maintenance-free spindle system, which reduces the need for regular upkeep and extends the overall life span of the mower.

The versatility of the deck also makes it compatible with several Cub Cadet riding mowers and lawn tractors, expanding its usability for a wide range of customers. Whether for tackling large yards or managing commercial properties, the Cub Cadet 48-inch Fabricated Deck proves to be an exceptional tool that combines strength, efficiency, and user-friendly features. Overall, this fabricated deck is an investment in quality lawn care, guaranteed to deliver outstanding performance and satisfaction for years to come.
Top Page Image Contents