Mulching, Inch Decks, Inch Becks | Cub Cadet LTI050 instruction

•For best results it is recommended that the first two laps be cut with the discharge thrown towards the center. After the first two laps, reverse the direction to throw the discharge to the outside for the balance of cutting. This will give a better appearance to the lawn.

•Under heavy conditions it may be necessary to go over the cut area a second time to get a clean cut.

•Do NOT attempt to mow heavy brush and weeds or extremely tall grass. Your tractor is designed to mow lawns, NOT clear brush.

•Keep the blades sharp and replace the blades when worn. Refer to CuttingBladeson page 25 of this manual for proper blade sharpening instructions.

Mulching

Cub Cadet Series 1000 tractors are equipped with a mulch kit which incorporates special blades, already standard on your tractor, in a process of recirculating grass clippings repeatedly beneath the cutting deck. The ultra-fine clippings are then forced back into the lawn where they act as a natural fertilizer. Observe the following points for the best results when mulching.

•Never attempt to mulch if the lawn is damp. Wet grass tends to stick to the underside of the cutting deck preventing proper mulching of the clippings.

•Do NOT attempt to mulch more than 1/3 the total height of the grass or approximately 1-1/2 inches. Doing so will cause the clippings to clump up beneath the deck and not be mulched effectively.

•Maintain a slow ground speed to allow the grass clippings more time to effectively be mulched.

•Always keep the throttle control lever in the FAST (rabbit) position while mowing. Failing to keep the engine at full throttle places strain on the tractor's engine and does not allow the blades to properly mulch grass.

NOTE: It is not necessary to remove the discharge chute to operate the mower with the mulch kit installed.

Carriage Screw

Plastic Wing Nut	Mulch Plug
NOTE:42-inch Deck Shown.

Figure 8

50-inch Decks

On model LTI050, the mulch kit is installed at the factory. To operate the cutting deck without mulching, simply remove the mulch plug by pivoting the discharge chute up and pulling the plug outward. To reinstall plug:

Locate two rectangular holes on the cutting deck surface.

•Pivot the discharge chute up to access the deck opening. See Figure 9.

•Insert the mulch plug, aligning the top edge of the plug with the deck as shown in the Figure 9. Make sure the notches on the plug are in the slots on the deck opening.

•Lightly tap on the plug with your hand to assure that the notches fit snugly under the chute tabs.

mulch plug while the engine is running.

_,ARNING: Never install or remove the

42- and 46-inch Becks

On model LT1042, LT1045 and LT1046 the mulch kit is installed at the factory. To operate the cutting deck without mulching, simply remove the mulch plug by unthreading the plastic wing nut which fastens it to the cutting deck. This will allow the clippings to discharge out the side. See Figure 8.

Mulch Plug

Figure 9

LTI050 specifications

The Cub Cadet LTI050 is a standout lawn care solution designed for both residential and commercial users who value efficiency and durability. With its powerful engine and innovative features, this riding lawn mower is built to tackle a variety of terrains while ensuring a high-quality cut.

At the heart of the LTI050 is a robust engine that delivers exceptional performance. Its reliable horsepower allows it to handle tough grass conditions with ease. This makes it suitable for larger lawns and properties where efficiency is key. The engine is designed for fuel efficiency, reducing the need for frequent refueling and providing longer operating times on a single tank.

One of the most notable features of the LTI050 is its cutting deck. The mower comes equipped with a high-performance cutting deck that offers precise results. Available in various cutting widths, it allows users to choose the best size for their mowing needs. The deck is engineered to enhance airflow and grass flow for a superior cut, resulting in a clean lawn appearance.

The Cub Cadet LTI050 also incorporates advanced technology that enhances the user experience. With its easy-to-use control panel, operators can easily adjust the mower settings, including cutting height and speed, with just a few simple steps. The inclusion of a hydrostatic transmission ensures smooth acceleration and deceleration, providing a more enjoyable mowing experience.

Comfort is a top priority in the LTI050 design. It features an ergonomic seat, adjustable steering, and strategically placed controls to minimize operator fatigue during extended use. The overall layout of the controls is intuitive, making it accessible for users of all experience levels.

Durability is another hallmark of the Cub Cadet brand, and the LTI050 is no exception. Constructed with high-quality materials and components, this mower is built to withstand the rigors of regular use. Its rugged frame and reinforced deck ensure it can handle challenging terrains without compromising performance.

Overall, the Cub Cadet LTI050 is a versatile and reliable choice for anyone looking to maintain a pristine lawn. With its high-performance engine, superior cutting technology, and user-friendly design, it represents a perfect blend of power and convenience, making lawn care a more efficient and pleasurable task. Whether for personal use or commercial landscaping, the LTI050 stands out as a top contender in its class.