Cub Cadet LTI050 manual Battery, CuttingDeckRemoval, Jump Starting, Charging

Page 26

Battery

California Proposition 65 Warning: Battery posts, terminals, and related accessories

contain lead and lead compounds, chemicals known to the State of California to cause

cancer and reproductive harm. Wash hands after handling.

The battery is sealed and is maintenance-free. Acid levels cannot be checked and fluid can not be added.

•Always keep the battery cables and terminals clean and free of corrosive build-up.

•After cleaning the battery and terminals, apply a

light coat of petroleum jelly or grease to both terminals

•Always keep the rubber boot positioned over the positive terminal to prevent shorting.

IMPORTANT: If removing the battery, disconnect the NEGATIVE (Black) wire from it'sterminal first, followed by the POSITIVE (Red) wire. When re-installing the battery, always connect the POSITIVE (Red) wire its

terminal first, followed by the NEGATIVE (Black) wire. Be certain that the wires are connected to the correct

terminals; reversing them could change the polarity and cause damage to your engine'salternating system.

Jump Starting

WARNING: Never jump start a damaged or

frozen battery. Be certain the vehicles do not touch, and ignitions are off. Do not allow cable clamps to touch.

•Connect positive (+) cable to positive post (+) of your tractor's discharged battery.

•Connect the other end of the cable to the (positive +) post of the jumper battery.

•Connect the second cable (negative -) to the other post of the jumper battery.

•Make the final connection on the engine block of the tractor, away from the battery. Attach to a unpainted part to assure a good connection.

IMPORTANT: If the jumper battery is installed on a vehicle (i.e. car, truck), do NOT start the vehicle's engine when jump starting your tractor.

•Start the tractor (as instructed on page 13).

•Set the tractor's parking brake before removing the jumper cables, in reverse order of connection.

Charging

WARNING: Batteries give off an explosive gas while charging. Charge the battery in a well ventilated area and keep away from an open flame or pilot light as on a water heater, space heater, furnace, clothes dryer or other gas appliances.

IMPORTANT: When charging your tractor's battery, use only a charger designed for 12V lead-acid batteries. Read your battery charger's Owner's Manual prior to charging your tractor's battery. Always follow its instructions and heed its warnings.

If your tractor has not been put into use for an extended period of time, charge the battery as follows:

1.Set your battery charger to deliver a maximum of 10 amperes.

2.If your battery charger is automatic, charge the battery until the charger indicates that charging is complete. If the charger is not automatic, charge for no fewer than eight hours.

CuttingDeckRemoval

To remove the cutting deck, proceed as follows:

•Place the PTO/Blade Engage knob in the

disengaged (OFF) position and engage the parking brake.

•Lower the deck by moving the deck lift lever into the bottom notch on the right fender.

•Remove the deck belt from around the tractor's electric PTO clutch (refer to Changingthe Beck Belt).

•Looking at the cutting deck from the left side of the

tractor, locate the deck support pin on the rear left side of the deck.

•Rotate the pin slightly toward the rear of the tractor and release it.

•Pull the deck support pin outward to release the deck from the deck lift arm. See Figure 20.

!

Figure 20

•Repeat the above steps on the tractor's right side.

•Move the deck lift lever into the top notch to raise the deck lift arms up and out of the way.

•Gently slide the cutting deck toward the front of the

tractor allowing the hooks on the deck to release themselves from the deck stabilizer rod.

•Gently slide the cutting deck (from the right side) out from underneath the tractor.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Operators Manual Tableofcontents Importantsafeoperationpractices California Proposition 65 WarningDataindicatesthatoperators,age60yearsand Towing MOWiHOIH REVERSEiSHOTHECOMMEHDED Seroljs iNJURY or DeathHEVERCARRYCHILDRENEVENWiTHBLADESOFF Sontsa 15o ShippingBraceRemoval AttachingtheBatteryCablesTRACTORSET-UP Tire PressureKnowyourlawntractor ThrottleControlLever IgnitionSwitchModuleSeatAdjustmentLever ChokeControlBrake BatteryCruiseControl PTOBlade EngageOperatingyourlawntractor SafetyInterlockSwitchesTo use the Reverse Caution Mode ReverseCautionModeStoppingthe Engine SettingtheGaugeWheelsStartingthe Engine DrivingTheTractor SettingTheCruiseControlEngagingtheParkingBrake MovingTheTractorManually UsingtheDeckLiftLeverOperatingtheHeadlights Mowing46-inch Becks MulchingInch Decks Front To Rear MakingadjustmentsLevelingthe Deck Sideto SideSteeringAdjustment ParkingBrakeAdjustmentSeatAdjustment EngineOil Recommendations MaintainingyourlawntractorEngine EngineOil TypeRe-fillingtheCrankcasewith Oil ChangingtheEngine011Changingthe Oil Filter AirFilter SmartJetTM Cleaningthe EngineAndDeckPaper ElementTwin Cylinder Engine Lubrication Carburetor AdjustmentTroubleshooting CuttingBlades TiresFuse Jump Starting BatteryCuttingDeckRemoval ChargingChangingTheTransmissionDriveBelt HydrostaticTransmission Changingthe DeckBeltAll Models LT1045& LT1046 Maintenanceschedule OFF-SEASONSTORAGEMaintenancelog Date Hour Meter Maintenance Performed byTroubleshooting Possible CausesATTACHMENTS& Accessories Attachment AccessoryReplacementparts IT1046 IT1050LTI050 SpecificationsLT1042 LT1045 CapacitiesManufacturers Warranty Coverage Kohlerco Page Cubcadet LLC, P.O. BOX361131CLEVELAND,OHIO44136-0019

LTI050 specifications

The Cub Cadet LTI050 is a standout lawn care solution designed for both residential and commercial users who value efficiency and durability. With its powerful engine and innovative features, this riding lawn mower is built to tackle a variety of terrains while ensuring a high-quality cut.

At the heart of the LTI050 is a robust engine that delivers exceptional performance. Its reliable horsepower allows it to handle tough grass conditions with ease. This makes it suitable for larger lawns and properties where efficiency is key. The engine is designed for fuel efficiency, reducing the need for frequent refueling and providing longer operating times on a single tank.

One of the most notable features of the LTI050 is its cutting deck. The mower comes equipped with a high-performance cutting deck that offers precise results. Available in various cutting widths, it allows users to choose the best size for their mowing needs. The deck is engineered to enhance airflow and grass flow for a superior cut, resulting in a clean lawn appearance.

The Cub Cadet LTI050 also incorporates advanced technology that enhances the user experience. With its easy-to-use control panel, operators can easily adjust the mower settings, including cutting height and speed, with just a few simple steps. The inclusion of a hydrostatic transmission ensures smooth acceleration and deceleration, providing a more enjoyable mowing experience.

Comfort is a top priority in the LTI050 design. It features an ergonomic seat, adjustable steering, and strategically placed controls to minimize operator fatigue during extended use. The overall layout of the controls is intuitive, making it accessible for users of all experience levels.

Durability is another hallmark of the Cub Cadet brand, and the LTI050 is no exception. Constructed with high-quality materials and components, this mower is built to withstand the rigors of regular use. Its rugged frame and reinforced deck ensure it can handle challenging terrains without compromising performance.

Overall, the Cub Cadet LTI050 is a versatile and reliable choice for anyone looking to maintain a pristine lawn. With its high-performance engine, superior cutting technology, and user-friendly design, it represents a perfect blend of power and convenience, making lawn care a more efficient and pleasurable task. Whether for personal use or commercial landscaping, the LTI050 stands out as a top contender in its class.
Top Page Image Contents