SettingtheGaugeWheels, Startingthe Engine

SettingtheGaugeWheels

Select the height position of the cutting deck by placing the deck lift lever in any of the six different cutting height notches on the right fender.

Adjust the deck wheels so that they are between l_-inch and _/2-inchabove the ground as follows.

from the discharge opening of the cutting

WARNING: Keep hands and feet away deck.

Place the tractor on a firm and level surface, preferably pavement. Refer to Figure 4, and proceed as follows:

•Place the tractor's deck lift handle in the normally desired mowing height setting, then check the

gauge wheels for contact or excessive clearance with the surface below.

ShoulderScrew

LockNut

ShoulderScrew

,ocelot\

Figure 4

If the wheels contact the surface adjust as follows:

a.Raise the deck lift handle to its highest setting.

b.Remove the rear gauge wheels by removing the lock nuts and shoulder screws which

secure them to the deck.

c.Remove the lock nuts and shoulder screws

which secure the front gauge wheels to the deck.

d.Place the deck lift handle in the desired mowing height setting.

e.Insert the shoulder screw with the rear gauge wheel into the index hole that leaves

approximately 1/2" between the bottom of the wheel and the pavement.

f.Note the position of the index hole used; then install the other rear gauge wheel and the front ball wheels into the corresponding index hole of the other gauge wheel brackets.

•If the gauge wheels have excessive clearance with the surface below, lower the wheels to the index

hole that provides the approximate 1/2" clearance as described above.

Refer to Levelingthe Deckon page 17 of this manual for more detailed instructions regarding various deck adjustments.

Startingthe Engine

interlock system is malfunctioning. This

WARNING: Do not operate the tractor if the system was designed for your safety and

protection.

NOTE: Refer to the TRACTORSET-UPon page 8 of this manual for Gasoline and Oil fill-up instructions.

•Insert the tractor key into the ignition switch module.

•Place the PTO (Blade Engage) knob in the disengaged (OFF) position.

•Engage the tractor's parking brake.

•Activate the choke control.

•Turn the ignition key clockwise to the START position. After the engine starts, release the key. It will return to the NORMAL MOWING position.

IMPORTANT: Do NOT hold the key in the START position for longer than ten seconds at a time. Doing so may cause damage to your engine'selectric starter.

•After the engine starts, deactivate the choke control.

NOTE: Do NOT leave the choke control on while operating the tractor. Doing so will result in a "rich" fuel mixture and cause the engine to run poorly.

Stoppingthe Engine

WARNING:		If you	strike	a	foreign	object,
stop the	engine	and disconnect			the spark plug
wire(s).	Thoroughly		inspect	the machine for
any damage.		Repair the		damage		before
restarting and operating

•If the blades are engaged, place the PTO/Blade Engage knob in the disengaged (OFF) position.

•Place the throttle control near the FAST position

•Turn the ignition key counterclockwise to the STOP position.

•Remove the key from the ignition switch to prevent unintended starting.

LTI050 specifications

The Cub Cadet LTI050 is a standout lawn care solution designed for both residential and commercial users who value efficiency and durability. With its powerful engine and innovative features, this riding lawn mower is built to tackle a variety of terrains while ensuring a high-quality cut.

At the heart of the LTI050 is a robust engine that delivers exceptional performance. Its reliable horsepower allows it to handle tough grass conditions with ease. This makes it suitable for larger lawns and properties where efficiency is key. The engine is designed for fuel efficiency, reducing the need for frequent refueling and providing longer operating times on a single tank.

One of the most notable features of the LTI050 is its cutting deck. The mower comes equipped with a high-performance cutting deck that offers precise results. Available in various cutting widths, it allows users to choose the best size for their mowing needs. The deck is engineered to enhance airflow and grass flow for a superior cut, resulting in a clean lawn appearance.

The Cub Cadet LTI050 also incorporates advanced technology that enhances the user experience. With its easy-to-use control panel, operators can easily adjust the mower settings, including cutting height and speed, with just a few simple steps. The inclusion of a hydrostatic transmission ensures smooth acceleration and deceleration, providing a more enjoyable mowing experience.

Comfort is a top priority in the LTI050 design. It features an ergonomic seat, adjustable steering, and strategically placed controls to minimize operator fatigue during extended use. The overall layout of the controls is intuitive, making it accessible for users of all experience levels.

Durability is another hallmark of the Cub Cadet brand, and the LTI050 is no exception. Constructed with high-quality materials and components, this mower is built to withstand the rigors of regular use. Its rugged frame and reinforced deck ensure it can handle challenging terrains without compromising performance.

Overall, the Cub Cadet LTI050 is a versatile and reliable choice for anyone looking to maintain a pristine lawn. With its high-performance engine, superior cutting technology, and user-friendly design, it represents a perfect blend of power and convenience, making lawn care a more efficient and pleasurable task. Whether for personal use or commercial landscaping, the LTI050 stands out as a top contender in its class.