Cub Cadet 8354 manual Battery Troubleshooting, Condition of Battery Cause Countermeasures

Page 53

BATTERY TROUBLESHOOTING

Condition of Battery

Cause

Countermeasures

Cause

 

 

 

 

Starter does not function

- Key is not "ON".

- Turn key "ON"

 

 

- Battery is over-used until

- Charge for a long period

- Do not overuse the

 

light becomes dim.

at the normal charging

battery and charge before

 

 

rate until specific gravity

being fully discharged.

 

 

of 1.26 is reached.

 

 

- Defective alternator or

- Repair alternator and

- Check alternator/rectifier.

 

rectifier preventing

replace defective rectifier,

 

 

charging of the battery.

and fully charge the

 

 

 

battery.

 

 

- Dirty or corroded terminal

- Wash terminal with hot

- Keep terminals clean and

 

contacts.

water and tighten well.

well tightened. Coat

 

 

 

terminals with grease to

 

 

 

prevent corrosion.

 

- Bad brushes, armature or

- Replace.

 

 

field in alternator.

 

 

 

- Life of battery expired.

- Replace battery.

 

 

 

 

 

Low electrolyte level

- Battery used with

- Add distilled water and

- Make routine checks of

 

shortage of electrolyte.

charge battery.

electrolyte.

 

- Battery over-used.

- Charge for a long period

- Do not overuse the

 

Charging was neglected.

at the normal charging

battery and charge before

 

(Refrain from over-

rate.

being fully discharged.

 

discharging)

 

 

 

- Defective alternator/

- Check alternator and

- Make routine checks of

 

rectifier, defective

rectifier, and charge for a

terminals to make sure

 

terminal contacts causing

long period at the normal

they are clean and tight

 

corrosion of electrodes.

charging rate.

 

 

 

 

 

Battery cannot be charged

- The current of the

- Decrease the charging

- Check charging current at

 

alternator during

current of alternator.

alternator.

 

operation is too high,

- Replaced damaged

 

 

causing plates to drop,

 

 

battery.

 

 

warp, or short circuit.

 

 

 

 

 

- Lift of battery expired

- Exchange battery.

 

 

 

 

 

Corrosion of terminals is

- Current of the alternator

- Clean corrosion from

- Keep terminals clean and

severe

during operation is too

terminals and tighten well.

well tightened.

 

high.

 

- Apply a coat of grease to

 

 

 

 

 

 

terminals to prevent

 

 

 

corrosion.

 

 

- Adjust charging current of

- Check charging current of

 

 

alternator.

alternator.

 

 

 

 

Electrolyte decreases

- Over heating due to over

- Check charging output.

 

rapidly

charging.

 

 

 

- Battery cracked or has

- Replace battery.

- Secure battery in tractor

 

small holes.

 

so it cannot move.

 

 

 

 

53

Image 53
Contents Operator’s Manual Important Read Safety Rules and Instructions CarefullyTo the Owner Table of ContentsCalling Service Information Plate Engine Serial no Recording Model and Serial Number InformationTractor General Operation Important Safe Operation PracticesPage Page Do not Slope OperationChildren Operating the PTO Safety Frame RopsService Page Safety Labels Safety Labels Ignition Switch Controls and FeaturesSwitches and Dash Mounted Controls Turn Signal Switch Light SwitchHazard Lamp Switch PTO SwitchInstrument Panel Forward/Reverse Shift LeverHand Throttle Lever Tachometer Hourmeter Brake Pedals Right and Left Floor Board and Fender Mounted ControlsClutch Pedal Main Shift Lever Foot ThrottleHi-Lo Range Shift Lever Auxiliary Hydraulics Lever OptionalBrake Pedal Lock Differential Lock PedalHydraulic Control Levers Mid PTO Lever Seat Adjustment LeverRollover Protective Structure Rops OperationPRE-STARTING Checks Fueling the TractorStarting the Engine NEW Tractor BREAK-IN ProceduresDriving the Tractor Stopping the EngineStopping the Tractor Driving on Roadways Turning the TractorDriving on Slopes Travel Speeds Check While OperatingUsing the Position Control and Draft Control Levers Using the Differential LockUsing the Front Wheel Drive Using the Drawbar Using the MID PTOGround Penetration w/Draft Control and Position Surface Penetration w/Draft Control OnlyTop Link Using the Three Point HitchLifting Rods Check LinksTractor Weighting Using Remote Hydraulics OptionalAdjusting the Seat AdjustmentsAdjusting Front Wheel TOE-IN Adjusting Front AxleBrake Adjustment Adjusting the FAN Belt TensionClutch Adjustment To Adjust Adjusting the Micro Switch HeightAdjusting Rear Wheel Tread Width Checking Steering Wheel General Information MaintenanceLubrication Table Service Intervals Operation to Lubrication and Maintenance ChartFuel System Accessing the Engine CompartmentChecking the Fuel Lines Bleeding the Fuel SystemServicing the Fuel Filter Adding Engine Oil Engine OIL and OIL FilterChecking the Engine Oil Level Changing Engine Oil and Filter Changing the Transmission Oil and Filter Transmission OIL and OIL FilterChecking the Transmission Oil Level Checking the Front Axle Oil Lever Servicing the Front AxleAdding Front Axle Oil Changing the Front Axle OilDraining the Clutch Housing Servicing the AIR CleanerChecking and Adding Coolant Checking and Cleaning Radiator ScreenServicing the Cooling System Lubricating the Tractor Changing the CoolantChecking the Radiator Hoses Brake pedal shaft both sides. See Figure General Battery Information Servicing the BatteryBattery Removal Battery MaintenanceBattery Storage Re-charging the BatteryServicing the Electrical System Fuses Fuse BoxMain Slow Blow Fuse Tire MaintenanceTractor Storage When Engine is Difficult To Start TroubleshootingEngine Troubleshooting When Color of Exhaust Is Especially Bad When Output Is InsufficientWhen the Engine Must Be Stopped Immediately When Engine Suddenly StopsTractor Troubleshooting When Tractor Does Not Move While Engine Is RunningCondition of Battery Cause Countermeasures Battery TroubleshootingModel SpecificationsPTO CLEVELAND, Ohio CUB Cadet LLC Post Office BOX