Harbor Freight Tools 47761 manual Extension Cords, Symbology, See Table a

Page 9

EXTENSION CORDS

1.Grounded tools require a three wire extension cord.

2.As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. (SeeTable A.)

3.The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.

WARNING! Do not use 16 or 18 AWG extension cords on this product.

4.When using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required. (See Table A.)

5.If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size.

(See Table A.)

6.If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.

7.Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.

Table A

RECOMMENDED MINIMUM WIRE GAUGE FOR POWER CORDS* (120 V)

NAMEPLATE AMPERES

(At Full Load)

POWER CORD LENGTH

 

25

50

OVER 50 FEET

 

Feet

Feet

 

 

 

 

 

 

12.1 - 16.0

14

12

Extension Cords must

 

 

 

16.1 - 20.0

12

10

NOT be used.

 

 

 

 

 

* Based on limiting the line voltage drop to five volts at 150% of the rated amperes.

SYMBOLOGY

Table B

SKU 47761

For technical questions, please call 1-800-444-3353;

PAGE 9

Troubleshooting section at end of manual.

 

 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Pressure Washer with Cart For technical questions or replacement parts, please callContents Safety SpecificationsGeneral Safety Rules Save this ManualPersonal Safety Electrical SafetyTool USE and Care ServiceDo not handle the Gfci Plug 95 with wet hands Specific Safety RulesSKU Grounded Tools Tools with Three Prong Plugs GroundingSymbology Extension CordsSee Table a Assembly Parts Diagrams on pagesSee Figure C, below Controls and Setup Controls and FeaturesAlter or disable the Gfci Power Plug Troubleshooting section at end of manual See Figure EFor technical questions, please call Setup See Figure C, OperationOperatingtips Become Familiar with Your MachineUSE Proper Pressure Washer Operation Techniques Cleaning Recommendations 3a. For a vertical or sloped surface3b. For a flat surface Do not use damaged equipment INSPECTION, MAINTENANCE, and CleaningMain Parts List Parts Lists and DiagramsMain Parts Diagram Parts List and Diagram a Please Read the Following Carefully Assembly Parts List and DiagramWater Leaking from Within the Housing TroubleshootingPressure Washer Stops Suddenly SKU For technical questions, please callTroubleshooting Pressure Washer will not StartPressure Washer does not Build Pressure Pressure Changes During USE Clean tip, using the includedTip CleanerDetergent will not Dispense Check that tip is free from debris and deposits

47761 specifications

Harbor Freight Tools is known for providing high-quality tools at affordable prices, and the 47761 model exemplifies this commitment. The 47761 is a versatile, compact air compressor, designed for various applications, from powering pneumatic tools to inflating tires and sports equipment.

One of the main features of the Harbor Freight Tools 47761 is its powerful 1.5 horsepower motor, which delivers an impressive maximum pressure of 125 psi. This ensures that users have enough power for demanding tasks while maintaining efficiency and performance. The compressor is equipped with a 3-gallon tank, which strikes a balance between portability and capacity, making it suitable for both home and professional use.

The compressor features a direct drive system that allows for low maintenance, as there are fewer moving parts compared to belt-driven models. Its lightweight design makes it easy to transport to job sites or store in tight spaces. Weighing in at just over 50 pounds, the 47761 is user-friendly, which is particularly beneficial during long tasks where convenience matters.

In terms of technologies, the Harbor Freight 47761 utilizes an oil-less pump. This means users do not need to worry about changing oil regularly, which can save time and resources. Additionally, the oil-less design reduces the chances of oil contamination, resulting in cleaner and safer operation.

Another significant characteristic of the 47761 is its noise level. Operating at a sound level of around 68 decibels, it is quieter than many standard compressors, providing a more pleasant working environment. An integrated pressure gauge allows for easy monitoring of the tank's pressure, enabling precision in various tasks.

The 47761 model is also equipped with overheating protection. This safety feature automatically shuts off the compressor if it becomes too hot, extending the lifespan of the unit and ensuring user safety.

Moreover, the compressor comes with a set of essential accessories, including an air hose and quick connect fittings, allowing users to start their projects immediately.

Overall, the Harbor Freight Tools 47761 is a reliable air compressor that combines power, efficiency, and ease of use, making it an excellent choice for DIY enthusiasts and professionals alike.
Top Page Image Contents