Craftsman 919.76235 Service Air Cleaner, Pre-Cleaner, Carburetor, Multi-Reg Wand/Lance

Page 13

Service Air Cleaner

Your engine is equipped with an oval dual element.

•To service element: loosen screws and lift cover. Then carefully remove pre-cleanerand cartridge assembly.

•After servicing pre-cleaner and cartridge, place pre-cleaner on cartridge.

•Install air cleaner assembly in base. Then install

cover on air cleaner and tighten screws securely to base.

sc-s Z

PRE-CLEANER _

CARTRIDGE

Pre-Cleaner

To service pre-cleaner, wash in liquid detergent and water. Allow to dry thoroughly before using. Do not oil pre-cleaner. Replace if very dirty or damaged.

NOTE: Do not use petroleum solvents, e.g., kerosene, which will cause the cartridge to deteriorate. Do not use pressurized air to clean cartridge. Pressurized air can

damage the cartridge.

Keep engine and parts cleanl

Carburetor

The carburetor of your high pressure washer is pre-setat the factory. The carburetor should not be tampered with. If your pressure washer is used at an altitude in excess of 5000 feet consult with your nearest Sears Service Center regarding high altitude set changes.

_, CAUTION: Engine speed was properly adjusted at the factory and should require no additional adjustment. Do not attempt to change engine speed. If you believe the engine is running too fast or too slow, take your pressure washer to a Sears Authorized Service Center for repair and adjustment.

increase the risk of personal injury or damage to

I A WARNING:equipment, High engine speeds are dangerous and

•Do not clean engine with a forceful spray of

water because water could contaminate fuel system.

With a brush or cloth, clean finger guard after every use to prevent engine damage caused by overheating.

CLEAN

CLEAN_

•Before running engine, clean muffler area.

CLEAN

Clean and Replace Spark Plug

Change the spark plug every 100 hours of operation or once each year, whichever comes first. This will help

your engine to start easier and run better.

.030" (0,76 MM)

WIRE GAGE

RESISTOR

I

•, CAUTION: Low engine speeds impose a heavy I load on the engine and when sufficient engine I power is not available could shorten engine life.

Nozzle cleaning:

If the nozzle becomes clogged with foreign materials, such as dirt, excessive pressure may develop. If the nozzle becomes partially clogged or restricted, the pump pressure will pulsate. Clean the nozzle immedi-

ately using the nozzle kit supplied and the following instructions:

Multi-Reg Wand/Lance:

1.Shut off the pressure washer and turn off the water supply.

2.Disconnect spark plug wire.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A IRItFTSMnNTable of Contents Hazard Risk of Explosion Or Fire HOW to Prevent ITWhat can Happen Breathing exhaust fumes will cause serious injury or deathNever point wand at, or spray people or animals HazardOwnersManual Nozzle Cleaning Kit and Replacement O-Rings Carton ContentsHazard Risk of HOT Surfaces What can Happen Bag ContainingTools Required for Assembly Adjustablewrench GAS HoseChoke Before Starting the Engine Not smoke or have open flame when tilting fuelTo operate the engine you will need to do Gasoline Your pressure washer engine is 4 cycle. Use freshRUN position To Start Your Pressure Washer High Pressure LOW Pressure How To Use Your Pressure Washer FAN Spray Stream Spray RPM TaskAIR Cleaner Pre-Cleaner Service Air CleanerCarburetor Multi-Reg Wand/LancePreparing Pressure Washer for Storage Engine Preparation Solution SymptomCause REF NO. Part no Craftsman 2350 PSi High Pressure WasherDescription REF NO. Part NO. DescriptionPage =KIT PER Part Description QTY307 11si 525 116A 987 108 127 130A 534 l Part 3os Part Description 373 6899560 855 51Length of Coverage Strattongasoline stabilizer,Part No Briggs&StrattonwelcomeswarrantyrepairandapologizesPage Page Part Crafisman Alta Presion Garanta Limitada DE UN AiO Para Lavadoras Craftsman DEGaranta Limitada DE UN Aiio DEL Motor Craftsman Sears, Roebuck and Co,, D/817 WA, Hoffman Estates, ILQuepuedesuceder RiesgoRiesgo DE INYEC¢ION DE Lquido Como PrevenirloLeere.jitl Manual IL/Prende r DetenerCduetlble Operad6n Riesgo QUE Puede Suceder Como PrevenirloImportante Preparaci6n de la Lavadora de Presi6n pare el Primer Uso Herramlentas Requeridas part= el EnsamblajeInterruptor Para Choke Palanquita de cebado para arrancar la unidadApagado de la Lavadora de Presi6n Hacer 1osiguiente para hacer que el motor funcioneAceite del Motor Mds fifo i-----4C/40F Mas caliente Sinttico 5W-30 SAESeguro PRESl6N Alta PRESl6N Baja Como user la Lavadora de Presi6nChorro EN Abanico Chorro Concentrado Luego enjuagadaResponsabilidades DEL Propietario En agua y sifonear agua por 1 a 2 minutosRecomendaciones Generales Especificaciones del Equipo Seguir estos pasos para eliminar ef aire de la bomba Carburador Filtro de Aire de Doble ElementoLimpiar y Reemplazar la Buja Limpieza de la BoquillaPreparaci6n Del Motor De ia Bomba Antes de almacenar la unidad por 30 dfas o ms. NuncaCausa SntomaSOLUCI6N VEA LA Pagina Version EN Ingles 052 Para Liste DE Partes VEA LA Pagina Version EN Ingles Para Liste DE VEA LA Pagina Version EN Ingles Page Page Sears
Top Page Image Contents