Craftsman 919.76235 owner manual To Start Your Pressure Washer, RUN position

Page 9

Use clean, fresh, regular unleaded gasoline with a minimum of 85 octane. Do not mix oil with gasoline. If unleaded fuel is unavailable leaded fuel may be used.

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as the carburetor, fuel filter hose or tank during storage. Also, experience indicates that alcohol-blendedfuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Never use engine or carburetor cleaner products in the fuel tank or perma- nent damage may occur.

NOTE: Never start pressure washer without water source turned on and connected to pressure washer.

To Start Your Pressure Washer

•Remove gas cap

•Add unleaded gasoline, slowIy, to fuel tank.

•Do not overfill.

•Connect garden hose to the water inlet on the

pressure washer. Tighten by turning water inlet counter clockwise.

•Connect high pressure hose to discharge on pump.

•Connect the garden hose to the water spout and turn water supply on.

•Squeeze trigger on pressure washer wand to relieve air pressure caused by turning on the water. Water will spew out of the gun in a thin stream. This will make it easier to start the engine.

•Engage the safety latch on the spray gun. This locks the trigger in place and keeps you from accidentally spraying a high pressure stream.

_LAAFETY

TCH

•On the engine there is a choke/run lever. Place lever to the choke position.

•On the engine there is a throttle control lever. Place throttle to the rabbit position. Always start engine with throttle in the rabbit (high speed) position.

CHOKE

•Grasp the starter grip and pull slowly until resistance is felt;, then pull firmly to start engine.

NOTE: If engine does not start right away, squeeze the trigger on the gun to relieve water pressure caused by turning on the water. Water will spew out of the gun in a thin stream. This will make it easier to pull start the engine. If more than five pulls are required, place choke lever back to run position.

•When engine starts, gradually move choke lever to

RUN position.

•For hot engine restarts, make sure throttle is in the rabbit (High speed) position and the choke lever is in the RUN position.

•Grasp the starter grip and pull slowly until resistance is felt; then pull firmly to start engine.

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A IRItFTSMnNTable of Contents Hazard Risk of Explosion Or Fire HOW to Prevent ITWhat can Happen Breathing exhaust fumes will cause serious injury or deathNever point wand at, or spray people or animals HazardOwnersManual Nozzle Cleaning Kit and Replacement O-Rings Carton ContentsHazard Risk of HOT Surfaces What can Happen Bag ContainingTools Required for Assembly Adjustablewrench Hose GASChoke Before Starting the Engine Not smoke or have open flame when tilting fuelTo operate the engine you will need to do Gasoline Your pressure washer engine is 4 cycle. Use freshRUN position To Start Your Pressure WasherHow To Use Your Pressure Washer High Pressure LOW PressureFAN Spray Stream Spray RPM TaskAIR Cleaner Pre-Cleaner Service Air CleanerCarburetor Multi-Reg Wand/LancePreparing Pressure Washer for Storage Engine Preparation Symptom SolutionCause REF NO. Part no Craftsman 2350 PSi High Pressure WasherDescription REF NO. Part NO. DescriptionPage =KIT PER Part Description QTY307 11si 525 116A 987 108 127 130A 534 l Part 3os Part Description 373 6899560 855 51Length of Coverage Strattongasoline stabilizer,Part No Briggs&StrattonwelcomeswarrantyrepairandapologizesPage Page Part Crafisman Alta Presion Garanta Limitada DE UN AiO Para Lavadoras Craftsman DEGaranta Limitada DE UN Aiio DEL Motor Craftsman Sears, Roebuck and Co,, D/817 WA, Hoffman Estates, ILQuepuedesuceder RiesgoRiesgo DE INYEC¢ION DE Lquido Como PrevenirloRiesgo QUE Puede Suceder Como Prevenirlo Leere.jitl Manual IL/Prende r DetenerCduetlble Operad6nImportante Preparaci6n de la Lavadora de Presi6n pare el Primer Uso Herramlentas Requeridas part= el EnsamblajeInterruptor Para Choke Palanquita de cebado para arrancar la unidadApagado de la Lavadora de Presi6n Hacer 1osiguiente para hacer que el motor funcioneAceite del Motor Mds fifo i-----4C/40F Mas caliente Sinttico 5W-30 SAESeguro PRESl6N Alta PRESl6N Baja Como user la Lavadora de Presi6nChorro EN Abanico Chorro Concentrado Luego enjuagadaEn agua y sifonear agua por 1 a 2 minutos Responsabilidades DEL PropietarioRecomendaciones Generales Especificaciones del Equipo Seguir estos pasos para eliminar ef aire de la bomba Carburador Filtro de Aire de Doble ElementoLimpiar y Reemplazar la Buja Limpieza de la BoquillaPreparaci6n Del Motor De ia Bomba Antes de almacenar la unidad por 30 dfas o ms. NuncaSntoma CausaSOLUCI6N VEA LA Pagina Version EN Ingles 052 Para Liste DE Partes VEA LA Pagina Version EN Ingles Para Liste DE VEA LA Pagina Version EN Ingles Page Page Sears

919.76235 specifications

The Craftsman 919.76235 is a high-performance air compressor designed for both professional and DIY enthusiasts. This versatile machine stands out in the market due to its robust build quality, efficient operation, and user-friendly design.

One of the main features of the Craftsman 919.76235 is its powerful motor. With a horsepower rating that drives a reliable pump, this air compressor is capable of delivering a consistent airflow that can handle a wide range of tasks, from inflating tires to powering pneumatic tools. The compressor has a substantial tank capacity, which allows for extended usage without frequent refilling, a significant advantage for those who require continuous air supply for their projects.

This air compressor operates at a maximum pressure of 135 PSI, which is suitable for most home and professional applications. The quick recovery time ensures that the compressor is back up to pressure shortly after pressure drops, allowing for uninterrupted work. The compressor also features a gauge that provides real-time feedback on the air pressure, enabling users to monitor their operations effectively.

Another standout characteristic is its portability. The Craftsman 919.76235 is designed with built-in wheels and a handle, making it easy to transport from one job site to another. This feature is particularly beneficial for contractors who work in various locations or for users who may need to move the unit around their workshop.

In terms of safety and maintenance, the Craftsman 919.76235 incorporates several thoughtful features. An automatic shut-off function prevents the compressor from over-pressurizing, which can lead to potential hazards. Additionally, the oil-free pump design means that users do not need to worry about regular oil changes, significantly reducing maintenance requirements and enhancing the machine's overall reliability.

The Craftsman 919.76235 is compatible with a variety of air tools, making it an excellent investment for both home use and professional applications. Whether it involves painting, nailing, or using impact wrenches, this air compressor meets diverse needs with ease.

In conclusion, the Craftsman 919.76235 air compressor delivers an impressive array of features, including a powerful motor, high maximum pressure, portability, and user-friendly operation. Its design prioritizes both efficiency and safety, making it an ideal choice for those seeking a dependable and versatile air compressor for various tasks.
Top Page Image Contents