Harman-Kardon Complete Guide to Configuring the Harman Kardon AVR 445 Remote Control

CONFIGURING THE REMOTE

The AVR 445 remote is factory-programmed for all functions needed to operate the unit. In addition, it is also preprogrammed to operate most recent Harman Kardon DVD players and changers, CD players and changers, CD recorders and cassette decks. The codes for other brand devices may be programmed into the AVR 445 remote using its extensive library of remote codes or a head-to-head learning process for codes not in the internal library.

As an alternative to the AVR remote, consider purchasing Harman Kardon’s TC 30 activity-based remote, which uses Web setup wizards to custom configure your remote. For more information visit www.harmankardon.com.

Thanks to the remote’s advanced technology and two-line LCD, it is no longer necessary to look up cumbersome codes when programming the remote; following the steps outlined below, you simply search for the brand name from the remote’s memory. We recommend that you first try the preprogrammed code entry method. If that procedure is not successful, then try the code-learning method.

Preprogrammed Code Entry

The easiest way to program the remote for operation with a source device from another brand is to follow these steps:

1.Turn on the power to the device you wish to pro- gram into the AVR remote. This is important, as in a later step you will need to see whether the device turns off to determine whether the remote has been programmed for the proper remote codes.

2.Press and hold the Program Button y for about 3 seconds while the message shown in Figure 25 appears in the remote’s LCD Information Display c. Release the button when the red light under the Set Button F appears.

H O L D P R O G B U T T O N

F O R 3 S E C O N D S

Figure 25

3.The remote’s MAIN MENU message (Figure 26), will appear in the LCD and the Set Button Fwill remain illuminated in red. Press the Set Button Fto begin the process of selecting a device and locating the proper remote codes.

M A I N M E N U

P R O G R A M D E V I C E

Figure 26

4.SELECT A DEVICE will appear in the LCD (Figure 27). Press the ⁄/ ¤ Navigation Button Dto scroll through the list of device categories and press the Set Button Fwhen the device

you wish to set the codes for appears. For this example, we will select “TV” to enter the codes needed to operate your TV.

S E L E C T A D E V I C E

T V

Figure 27

NOTE: The codes for hard-drive recorder products (DVR) such as TiVo® are programmed by selecting VCR as the device. For satellite-based TiVo products, check under the brand name of the product.

5.At the next menu screen on the remote (Figure 28), press the Set Button Fto enter the Manual mode, which means that you will select the brand name of the device from the list pro- grammed into the remote’s memory.

P R O G R A M D E V I C E

M A N U A L

Figure 28

6.The next menu screen on the remote (Figure 29) will show the start of the list of available brands. Press the ⁄/ ¤ Navigation Buttons Duntil the brand name of the device you are program- ming into the remote appears on the lower line of the display and then press the Set Button F.

S E L E C T B R A N D

R C A

Figure 29

NOTE: If the brand name for the product you wish to program does not appear in the list, the codes may still be available, as some manufacturers share codes. If the desired brand is not listed, press the Clear Button j to exit the programming process, and skip to the instructions shown on page 47 for the “Automatic” method of programming the remote. If desired, or if the codes for your brand are not part of the remote’s library at all, you may still use the remote to program most infrared-controlled products by “learning” the commands from the product’s original remote into the AVR remote. The instructions for Learning Commands are on page 47.

7.The next step is important, as it determines which codes will operate the source device or display. Point the AVR remote at the device being pro- grammed and, following the instructions shown in the remote’s LCD Information Display c, press and release the Numeric Keys cshown on the menu screen (Figure 30) one at a time, starting with the “1” button. After you press the “1” Button c, the remote’s LCD screen will briefly go blank as the code is being transmitted,

but you will see the “transmit” icon in the upper right corner of the display to serve as confirmation that the remote is sending out commands.

P R E S S A N U M B E R

C O D E 1 O F 1 0

Figure 30

8.After you press and release the number key, watch the device being programmed to see whether it turns off. As shown in the instructions that will appear on the next menu screen (Figure 31), if your device has turned off, press the Set Button F, and then skip to Step 10. If the unit does not turn off, proceed to the next step.

P O W E R O F F ? Y : S E T

N : N E X T # O R C L R

Figure 31

9.If the device being programmed into the AVR remote does not turn off after you have pressed the “1” Button c, repeat Steps 7 and 8 by pressing the available numeric keys shown until the device turns off. If the device still does not turn off after all choices have been tried, or if there is only one number key shown as available to try, the code for this specific device is not in the AVR remote library under that brand name. If that is the case, press the Clear Button j to exit the manual programming mode. Remember that the codes may still be stored in the AVR remote’s library under another brand, and you can have the remote control search for them by following the instructions below for automatic programming. You may also manually “learn” the codes for most devices into the AVR remote by following the Learning Commands instructions on page 47.

10.When the device being programmed does turn off after a numeric key has been pressed, you must press the Set Button Fwithin 5 seconds to enter the setting into the remote’s memory. After you press the Set Button F, the top line of the LCD will read SAVING… and then the word SAVED will flash four times in the center of

the bottom line.

11.When the codes are saved, the remote will return to normal operation, and whenever you press the Input Selector Button d that was just programmed, the codes for the new device will be used. If no further buttons are pressed, the remote will revert back to the default setting for AVR commands.

NOTE: Some brands share a common remote control code for “Power Off” for many models. For that rea- son, it is possible that even though the remote appears to be properly programmed, you may find that some buttons do not appear to issue the correct command. If this is the case, repeat the procedure outlined above, but if more than one numeric key selec- tion is suggested in Step 7, try a different number to

46 CONFIGURING THE REMOTE