CONFIGURING THE REMOTE
•When the RENAME DEVICE option is offered by the remote after the code is pro- grammed, you will be changing the name that is shown in the remote’s LCD every time that Input Selector is pressed.
Changing Devices
In the factory default settings, the AVR remote is programmed so that the commands transmitted correspond to the device selected by pressing one of the Input Selectors 3. This is logical, as you want the remote to control the device you have selected. However, in some circumstances you may have con- figured your system so that the devices connected to the AVR 445 do not correspond to the default device settings and the legends printed on the remote. For example, if your system has two VCRs you may con- nect the second VCR to the VID 2 input. There is no problem in doing that, but in normal operation the commands issued after selecting the VID 2 input are for a television, not a VCR.
The AVR remote allows you to correct that situation through the “Changing Devices” process. This enables you to assign the codes from one type of device to a different button. For example, in the steps below, we will explain how to program the VID 2 buttons to provide the commands to operate a VCR. Of course, you may program the remote to have any of the devices take on the code set of any other device, as your system requires. And, with the AVR remote’s “Rename” function, you can even change the way the name of the device appears on the remote’s LCD so that you see exactly which commands are being sent.
To program the buttons normally assigned to one device for the commands of another, please follow these steps:
1.Press and hold the Program Button Ofor about three seconds while the message shown in Figure 25 appears in the remote’s LCD Information Display 2. Release the button when the red light under the Set Button F appears.
2.The remote’s MAIN MENU message (Figure 26), will appear in the LCD and the Set Button Fwill remain illuminated in red. Press the ⁄ Navigation Button Dtwice so that CHANGE DEVICE appears on the bottom line of the LCD screen, as shown in Figure 45. Press the Set Button Fto begin the process of reassigning the commands used for a particular device.
M A I N M E N U
C H A N G E D E V I C E
Figure 45
3.The next menu display is where you select the Input Select, or device, that you wish to change. When the display shown in Figure 46 appears, press the ⁄/ ¤ Navigation Button Dto scroll through the list to find the device you wish to use for another function. In this case we will select “TV,” and show how to change it to take on the codes for operating a VCR. When that device’s name appears, press the Set Button F.
O L D D E V I C E T Y P E
T V
Figure 46
4.Once the “old” device type has been selected, you need to tell the remote which set of remote codes to use as a replacement for the device just selected. When the instructions shown in Figure
47 appear, press the ⁄/ ¤ Navigation Button Dto scroll through the list of device categories to find the name of the device that you wish to use. The old device name will remain on the left side of the LCD screen, while the replacement device list will scroll to its right. For example, press the ⁄ Navigation Button Duntil the display screen reads
N E W D E V I C E T Y P E
T V < - V C R
Figure 47
5.Once the new device is selected, the remainder of the process will select the codes for the specific brand to be used, and for that reason they are identical to the way a device is programmed using manual entry. Continue the process as outlined in the next few steps, remembering that if the codes for your specific device are not found, you may select any brand and then “learn” the proper codes into the AVR remote using the process out- lined on page 49. To begin the process, start by selecting the brand of device, as shown in Fig. 29. Press the ⁄/ ¤ Navigation Button Duntil the brand name of the device you are programming into the remote appears on the lower line of the display and then press the Set Button F.
6.The next step is important, as it determines which codes will operate the source device or display. Point the AVR remote at the device being pro- grammed and, following the instructions shown on the remote’s LCD Information Display 2, press and release the Numeric Keys cone at a time, starting with the “1” Button c. After you press the “1” Button c, the remote’s LCD screen will briefly go blank as the code is
being transmitted, but you will see the “transmit” icon in the upper right corner of the display to serve as confirmation that the remote is sending out commands.
7.After you press and release the number key, watch the device being programmed to see whether it turns off. As shown in the instructions that will appear on the next menu screen (Figure 31), press the Set Button F, and then skip to Step 9. If the unit does not turn off, proceed to the next step.
8.If the device being programmed into the AVR remote does not turn off after you have pressed the “1” Button c, continue Steps 6 and 7 by pressing the available numeric keys shown until the device turns off. If the device still does not turn off after all choices have been tried, the code for this specific device is not in the AVR remote library under that brand name. If that is the case, we suggest that you press the Set Button F to accept the codes from another brand so that the programming is completed, but remember that you will then have to program the remote manually by following the Learning Commands instructions on page 47.
9.When the device being programmed does turn off after a numeric key has been pressed, you must press the Set Button Fwithin five seconds to enter the setting into the remote’s memory. After you press the Set button, the top line of the LCD will read SAVING... and then the word SAVED will flash four times in the center of the bottom line.
10.When the codes are saved the remote will return to normal operation, and whenever you press the Input Selector Button 3that was just programmed, the display will show the original
Macro Programming
Macros enable you to easily repeat frequently used combinations of multiple remote control commands with the touch of a single button. Once a macro is programmed, you may send up to 20 commands with one press of the Power On or Macro buttons. This will greatly simplify the process of turning on your system, changing devices or other common tasks. Thanks
to the remote’s
CONFIGURING THE REMOTE 49
