Harman-Kardon AVR 445 owner manual Front-Panelcontrols, is installed

FRONT-PANEL CONTROLS

4Tuning Selector: Press the left side of the button to tune lower-frequency stations and the right side of the button to tune higher-frequency stations. When the tuner is in the MANUAL/MONO mode, each tap of the Selector will increase or decrease the frequency by one increment. When the tuner receives a signal strong enough for adequate reception, MANUAL TUNED will appear in the Lower Display Line $ and in the on-screen display. When the tuner is in the AUTO/STEREO mode, press the button once, and the tuner will scan for a station with acceptable signal strength. When the next higher- or lower-frequency station is tuned, the frequency scan will stop and the Lower Display Line $ and the on-screen display will indicate AUTO TUNED. When an FM stereo station is tuned, the display will read AUTO ST TUNED. See page 39 for more information on using the tuner. When an XM Ready module is connected and activated, and when there is sufficient signal strength for the XM system to operate, pressing this button will also change the XM Radio channel.

5 Tuner Band Selector: Pressing this button will automatically switch the AVR 445 to the Tuner mode. Pressing it again will select the AM or FM frequency band, or XM Radio. (See page 39 for more informa- tion on the tuner.)

6 Preset Station Selector: Press this button to scroll up or down through the list of stations that have been entered into the preset memory. (See page 39 for more information on tuner programming.)

7 Input Source Selector: Press this button to change the input by scrolling up or down through the list of input sources.

8 Tuning Mode Selector: Press this button to select Auto or Manual tuning. When the button is pressed so that AUTO/STEREO appears in the Upper Display Line #, the tuner will search for the next station with an acceptable signal when the Tuning Selector 4Mπ is pressed. When the button is pressed so that MANUAL/MONO appears in the Upper Display Line #, each press of the Tuning Selector 4Mπ will increase the frequency. (See page 39 for more information on using the tuner.)

This button may also be used to switch between Stereo and Mono modes for FM radio reception. When weak reception is encountered, select the Manual/Mono tuning mode. Press and hold again to switch back to Stereo mode. (See pages 39 for more information on using the tuner.)

When an optional XM Connect & Play module is con- nected and activated, and when there is sufficient sig- nal strength for the XM system to operate, this button has a different set of functions than when traditional AM or FM radio is in use. See page 39 for more infor- mation on XM Radio operation.

9 Front-Panel Door: To open the door so that the front-panel jacks and controls behind this door may be accessed, gently pull the door down and toward you, using either upper corner of the door.

) Volume Control: Turn this knob clockwise to increase the volume, counterclockwise to decrease the volume. If the AVR 445 is muted, adjusting the volume control will automatically release the unit from the silenced condition.

!Input Indicators: One of these indicators will light to identify the currently selected input. Note that the entire list will light briefly each time the unit is turned on, as a test.

@Speaker/Channel Input Indicators: These indi- cators are multipurpose, indicating both the speaker type selected for each channel and the incoming data- signal configuration. The left, center, right, right surround and left surround speaker indicators are composed of three boxes, while the subwoofer is indicated by one box. The center box lights when a “small” speaker is selected, and the two outer boxes light when “large” speakers are selected. When none of the boxes are

lit for the center, surround or subwoofer channels, no speaker has been assigned that position. The letters inside each box display the active input channels. For standard analog inputs, only the L and R will light, indi- cating a stereo input. For a digital source, the indicators will light to display the channels being received at the digital input. When the letters flash, the digital input has been interrupted. (See page 38 for more information on the Channel Indicators.)

#Upper Display Line: Depending on the unit’s status, a variety of messages will appear here. In normal operation, this line will show the current input source and identify whether an analog or digital input is in use. When the tuner is selected as the input, this line will identify the station as AM or FM and show the frequency and preset number, if any.

When an XM Connect & Play module is connected and activated, and when there is sufficient signal strength for the XM system to operate, the XM chan- nel number and signal strength will appear here.

$ Lower Display Line: Depending on the unit’s status, a variety of messages will appear here. In nor- mal operation, the current surround mode will appear on this line. When an XM Ready module is connected and activated, and when there is sufficient signal strength for the XM system to operate, a variety of messages and information, including the XM channel title name, the current artist and track title, the XM Radio channel category and, when available, local traffic and weather information, will appear here.

%Surround Mode Indicators: One of these indicators will light to show the surround mode in use. Depending on the specific combination of input sources and surround mode selected, more than one indicator may light. (See page 36 for more information.)

^Remote Sensor Window: The sensor behind this window receives infrared signals from the remote control. Aim the remote control at this area, and do not block or cover it unless an external remote sensor

is installed.

6 FRONT-PANEL CONTROLS